The functions to detect the state of the ready / busy signal is already
available but only used in the SPL case. Lets use it always, also for the
main U-Boot. As all boards should have this HW connection.
Testing on Siemens Draco (am335x) showed a small perfomance gain by using
this ready pin to detect the NAND chip state. Here the values tested on
Draco with Hynix 4GBit NAND:
Without NAND ready pin:
U-Boot# time nand read 80400000 0 400000
NAND read: device 0 offset 0x0, size 0x400000
4194304 bytes read: OK
time: 2.947 seconds, 2947 ticks
With NAND ready pin:
U-Boot# time nand read 80400000 0 400000
NAND read: device 0 offset 0x0, size 0x400000
4194304 bytes read: OK
time: 2.795 seconds, 2795 ticks
So an increase of approx. 5%.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Re-map NAND&I2C boot-device to the "normal" NAND boot-device.
Otherwise the SPL boot IF can't handle this device correctly.
Somehow booting with Hynix 4GBit NAND H27U4G8 on Siemens
Draco leads to this boot-device passed to SPL from the BootROM.
With this change, Draco boots just fine into main U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
The comments on the QSPI pad assignments erronously swapped
the qspi1_d0 and qspi1_d1 functionality and could cause
confusion. QSPI1_D[0] is in fact muxed on pad U1 (gpmc_a16),
and QSPI1_D[1] - on pad P3 (gpmc_a17). Fixing comments.
Signed-off-by: Lubomir Popov <l-popov@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Boards using the TWL4030 regulator may not all use the LDOs the same way
(e.g. MMC2 power can be controlled by another LDO than VMMC2).
This delegates TWL4030 MMC power initializations to board-specific functions,
that may still call twl4030_power_mmc_init for the default behavior.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Fix omap3_evm warning, add twl4030.h]
Signed-off-by: Tom Rini <trini@ti.com>
Not every device has multiple MMC slots available, so it makes sense to enable
only the required LDOs for the available slots. Generic code in omap_hsmmc will
enable both VMMC1 and VMMC2, in doubt.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
Some devices may use non-standard combinations of regulators to power MMC:
this allows these devices to provide a board-specific MMC power init function
to set everything up in their own way.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
BeagleBoard-X15 is the next generation Open Source
Hardware BeagleBoard based on TI's AM5728 SoC
featuring dual core 1.5GHZ A15 processor. The
platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x108@60),
separate LCD port, video In port, 4GB eMMC, uSD,
Analog audio in/out, dual 1G Ethernet.
For more information, refer to:
http://www.elinux.org/Beagleboard:BeagleBoard-X15
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
just add a few ifdefs around because this
device is very similar to dra7xxx.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
expose those two definitions so they can be
used by another board which we're adding in upcoming
patches.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
this will allow for boards to overwrite those
in case memory setup is different.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
* Since the emmc isn't always programed trying to load the fs from the
emmc causes boot failures/kernel panic.
* The current bootcmd is set to:
bootcmd=run findfdt; run mmcboot;setenv mmcdev 1; setenv bootpart 1:2; \
setenv mmcroot /dev/mmcblk0p2 rw; run mmcboot;
My guess is the env variables should be set so that sd card boot
(dt,kernel,fs) is the default and then fallback to emmc if it fails (no
sd card detected)
The current bootcmd attempts to set mmcroot to the sd card rootfs but
that code doesn't run due to mmcboot being ran early on.
Signed-off-by: Franklin Cooper Jr. <fcooper@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
If we want to have two sections, one on each EMIF, without
interleaving, current code wouldn't enable emif2. Fix that
problem.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
there's no such function usb3_phy_power(),
it's likely that author meant to call,
usb_phy_power() instead, but that's already
called properly from xhci-omap.c.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
some boards might want to use USB1 for host,
without fiddling those registers it'll be
impossible.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Those regulators don't have any coupling with
what they supply, so remove the suffixes in order
to not confuse anybody.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Out of all OMAP5-like boards, only one of them
needs CONFIG_MISC_INIT_R, so it's best to enable
that for that particular board only, instead of
enabling for all boards unconditionally.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
It has been found that this change breaks the case of an appended device
tree file, so for the problem in question some other solution must be
found.
This reverts commit c6150aaf2f.
Reported-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Reported-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Confirmed-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Tom Rini <trini@ti.com>
The changes to introduce loff_t into filesize means that we need to do
64bit math on 32bit platforms. Make sure we use the right wrappers for
these operations.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Suriyan Ramasami <suriyan.r@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Pierre Aubert <p.aubert@staubli.com>
After commit 933cdbb479: "fdt: Try to use fdt_address_cells()/fdt_size_cells()"
I noticed that allwinner boards would no longer boot.
Switching to fdt_address_cells / fdt_size_cells changes the result from
bytes to 32 bit words, so when we increment pointers into the blob, we must
do so by 32 bit words now.
This commit makes allwinner boards boot again.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Vince Hsu <vinceh@nvidia.com>
If CONFIG_OF_CONTROL is defined, search device tree nodes that are
compatible with "panasonic,uniphier-ehci" and take the base address
from their "reg" property.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Marek Vasut <marex@denx.de>
This commit implements the ofdata_to_platdata handler for the UniPhier
serial driver and adds serial device nodes to the device tree sources.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled.
It includes <asm/gpio.h> and then <asm/gpio.h> includes
<asm/arch/gpio.h>. Consequently, all the SoCs that enable
CONFIG_OF_CONTROL must have <asm/arch/gpio.h> even if they do not
support GPIO.
In the first place, GPIO has nothing to do with OF_CONTROL.
It is wrong that lib/fdtdec.c includes GPIO functions; it should
be split into two files, FDT-common things and GPIO things.
It is, however, a pretty big work to fix that correctly.
This is a compromised commit to add a dummy <asm/arch/gpio.h>
to support OF_CONTROL for UniPhier platform. This dummy header
will be removed after FDT-GPIO stuff is fixed correctly.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_path_offset() checks an alias too.
fdtdec_get_alias_node(blob, "foo") is equivalent to
fdt_path_offset(blob, "foo").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
The initramfs is currently only relocated if the user calls
the bootm ramdisk subcommand. If bootm should be used without
subcommands, the arch-specific bootm code needs to implement
the relocation.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
After all MIPS boards are switched to generic-board, the
MIPS specific board.c can be removed.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
To get correct stack walking and backtrace functionality in gdb,
registers fp and ra should be initialized before calling board_init_f
or board_init_r. Thus allocating stack space and zeroing it as it is
currently done in board.c becomes obsolete.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Merge struct s3c2410_nand and struct s3c2440_nand into one unified
struct s3c24x0_nand. While at it, fix up and rename the functions
to retrieve the NAND base address and fix up the s3c NAND driver to
reflect this change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
This patch disables subpage writes for vf610_nfc nand
driver. This is required, as without this fix, writing
unaligned u-boot images with DFU results in a hang.
Trying to write unalgined binary images also results
in a hang, without disabling subpage writes.
Patch has been tested on a Colibri VF61 module.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Some but not all of implementations of the Denali NAND controller
have hardware circuits to detect the device parameters such as
page_size, erase_size, etc. Even on those SoCs with such hardware
supported, the hardware is known to detect wrong parameters for some
nasty (almost buggy) NAND devices. The device parameters detected
during nand_scan_ident() are more trustworthy.
This commit sets some hardware registers to mtd->pagesize,
mtd->oobsize, etc. in the code between nand_scan_ident() and
nand_scan_tail().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Chin Liang See <clsee@altera.com>
Some variants of the Denali NAND controller need some registers
set up based on the device information that has been detected during
nand_scan_ident().
CONFIG_SYS_NAND_SELF_INIT has to be defined to insert code between
nand_scan_ident() and nand_scan_tail(). It is also helpful to reduce
the difference between this driver and its Linux counterpart because
this driver was ported from Linux. Moreover, doc/README.nand recommends
to use CONFIG_SYS_NAND_SELF_INIT.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Chin Liang See <clsee@altera.com>
Commit ff94bc40af
("mtd, ubi, ubifs: resync with Linux-3.14")
accidentally reverted part of the commit
13f0fd94e3
("NAND: Scan bad blocks lazily.").
Reinstate the change as by commit
fb49454b1b
("nand: reinstate lazy bad block scanning")
Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
Acked-by: Heiko Schocher <hs@denx.de>
Commit 9f12cd0e06 has broken SPL EXT support.
This patch update error code check to get SPL EXT support working again.
Tested on a Pandaboard (rev. A3).
Reviewed-by: Suriyan Ramasami <suriyan.r@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@ti.com>
