Starting with PCB revision 3 we can safely make use of higher RAM
frequency again. Make use of the EEPROM detection to determine the
revision and use the updated RAM timings for new SoMs.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Add EEPROM detection initialisation for phyCORE-i.MX8MM and
print SoM information during boot when successful.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Due to PCB layout constraints in PCB revisions until including 1549.2,
a RAM frequency of 2 GHz can cause rare instabilities. Set the RAM
frequency to 1.5 GHz to achieve a stable system under all conditions.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
pinctrl_wdog already marked u-boot,dm-spl, so clean up board code.
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Enable CONFIG_DM_SERIAL. uart and its pinmux was already
marked with u-boot,dm-spl.
Move preloader_console_init after spl_early_init to make sure driver
model work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This is supposed to be a build-system flag. Move it there so we can
define it before linux/kconfig.h is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
binman conversion made flashing flash.bin
and u-boot.itb necessary. Update binman config
to create a single flash.bin image again.
This updates imx8mp_evk and phyCORE-i.MX8MP as they share the
same binman config.
Updated also imx8mp_evk documentation.
Tested on phyCORE-i.MX8MP.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
- Provide a default Kconfig value of the default script
- Largely continue to define this via the board Kconfig file
- For the boards that select a script based on defconfig rather than
TARGET, keep this within the defconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Increase VDD_ARM to prevent timing issues as VDD_SOC is
used in OD mode. Also increase GIC clock.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable support for the fec ethernet on phyCORE-i.MX8MP.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Currently PCA9450 might have address 0x25 or 0x35, so let user
choose the address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
