Add power domain nodes to DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
The fsl,usbphy DT property is deprecated, replace it with phys DT
property and specify #phy-cells, so that the generic PHY framework
can parse the PHY bindings without any extra hacking.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
The fsl,usbphy DT property is deprecated, replace it with phys DT
property and specify #phy-cells, so that the generic PHY framework
can parse the PHY bindings without any extra hacking.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
The standard compatible string is "usb-nop-xceiv", use it.
Note that keystone-k2g.dtsi already uses the aforementioned
compat string, so this patch can only remove the override.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
The USB no-op PHY uses "usb-nop-xceiv" compatible string. This driver is
compatible with USB no-op PHY, so add the compatible string.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Variable "final" will have SHA512 digest, but currently
the array size is not sufficient. Let's fix it.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If realloc() fails, we should free the old buffer.
Fixes: c74cd8bd08: ("efi_loader: capsule: add capsule_on_disk support")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Remove function invocations using the EFI_CALL macro for those
functions that do not have an EFI_ENTRY call in their definition. Such
functions can use u-boot api's which rely on u-boot global data(gd)
pointer. The Arm and RiscV architectures maintain a separate gd
pointer, one for u-boot, and a separate gd for the efi application.
Calling a function through the EFI_CALL macro changes the gd pointer
to that used for the efi application, with u-boot gd being
unavailable. Any function then trying to dereference u-boot's gd will
result in an abort.
Fix this issue by removing the EFI_CALL macro for all of such
functions which do not begin by an EFI_ENTRY function call.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Two external references cannot have the same name:
doc/chromium/overview.rst:5:
WARNING: Duplicate explicit target name: "youtube"
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
In reStructured text footnotes are referenced like [1]_.
Add missing underscores.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Marek Vasut <marex@denx.de>
The length of an underline must match the length of the header.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
As the the SPI flash is probed and is released in each ENV sf function
the env_flash no more need to be static.
This patch move this device handle as local variable of each function and
simplify the associated code (env_flash is never == NULL when
setup_flash_device is called).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Free the SPI resources by calling spi_flash_free() in each env sf
function to avoid issue for other SPI users.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add support of opts erase for env in SPI flash;
this opts is used by command 'env erase'.
This command only fills the env offset by 0x0 (bit flip to 0) and
the saved environment becomes invalid (with bad CRC).
It doesn't erase the sector here to avoid issue when the sector
is larger than the env (i.e. embedded when
CONFIG_ENV_SECT_SIZE > CONFIG_ENV_SIZE).
The needed sector erase will be managed in the next "env save" command,
using the opt ".save", before to update the environment in SPI flash.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add ENV_ERASE_PTR macro to handle erase opts and remove the associated
ifdef.
This patch is a extension of previous commit 82b2f41357 ("env_internal.h:
add alternative ENV_SAVE_PTR macro").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This fixes the case where there are multiple environment drivers, one of
them is the default environment one, and it is followed by an environment
driver which does not implement .init() callback. The default environment
driver sets gd->env_valid to ENV_INVALID and returns 0 from its .init()
callback implementation, which is valid behavior for default environment.
Since the subsequent environment driver does not implement .init(), it
also does not modify the $ret variable in the loop. Therefore, the loop
is exited with gd->env_valid=ENV_INVALID and ret=0, which means that the
code further down in env_init() will not reset the environment to the
default one, which is incorrect.
This patch sets the $ret variable back to -ENOENT in case the env_valid
is set to ENV_INVALID by an environment driver, so that the environment
would be correctly reset back to default one, unless a subsequent driver
loads a valid environment.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Since commit 0f036bf4b8 ("env: Warn on force access if ENV_ACCESS_IGNORE_FORCE set")
a warning message is displayed when setenv -f is used WITHOUT
CONFIG_ENV_ACCESS_IGNORE_FORCE, but the variable is set anyway, resulting
in lots of log pollution.
env_flags_validate() returns 0 if the access is accepted, or non zero
if it is refused.
So the original code
#ifndef CONFIG_ENV_ACCESS_IGNORE_FORCE
if (flag & H_FORCE)
return 0;
#endif
was correct, it returns 0 (accepts the modification) if forced UNLESS
IGNORE_FORCE is set (in which case access checks in the following code
are applied). The broken patch just added a printf to the force accepted
case.
To obtain the intent of the patch we need this:
if (flag & H_FORCE) {
#ifdef CONFIG_ENV_ACCESS_IGNORE_FORCE
printf("## Error: Can't force access to \"%s\"\n", name);
#else
return 0;
#endif
}
Fixes: 0f036bf4b8 ("env: Warn on force access if ENV_ACCESS_IGNORE_FORCE set")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
If one of the reads fails when importing redundant environments (a
single read failure), the env_flags wouldn't get initialized in
env_import_redund(). If a user then calls saveenv, the new environment
will have the wrong flags value. So on the next load the new environment
will be ignored.
While debugging this, I also noticed that env/sf.c was not correctly
handling a single read failure, as it would not check the crc before
assigning it to gd->env_addr.
Having a special error path for when there is a single read failure
seems unnecessary and may lead to future bugs. Instead collapse the
'single read failure' error to be the same as a 'single crc failure'.
That way env_check_redund() either passes or fails, and if it passes we
are guaranteed to have checked the CRC.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is roughly the U-Boot side equivalent to commit
e282c422e0 (tools: fw_env: use erasesize from MEMGETINFO ioctl). The
motivation is the case where one has a board with several revisions,
where the SPI flashes have different erase sizes.
In our case, we have an 8K environment, and the flashes have erase
sizes of 4K (newer boards) and 64K (older boards). Currently, we must
set CONFIG_ENV_SECT_SIZE to 64K to make the code work on the older
boards, but for the newer ones, that ends up wasting quite a bit of
time reading/erasing/restoring the last 56K.
At first, I wanted to allow setting CONFIG_ENV_SECT_SIZE to 0 to mean
"use the erase size the chip reports", but that config
option is used in a number of preprocessor conditionals, and shared
between ENV_IS_IN_FLASH and ENV_IS_IN_SPI_FLASH.
So instead, introduce a new boolean config option, which for now can
only be used with ENV_IS_IN_SPI_FLASH. If left off, there's no change
in behaviour.
The only slightly annoying detail is that, when selected, the compiler
is apparently not smart enough to see that the the saved_size and
saved_offset variables are only used under the same "if (sect_size >
CONFIG_ENV_SIZE)" condition as where they are computed, so we need to
initialize them to 0 to avoid "may be used uninitialized" warnings.
On our newer boards with the 4K erase size, saving the environment now
takes 0.080 seconds instead of 0.53 seconds, which directly translates
to that much faster boot time since our logic always causes the
environment to be written during boot.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
As preparation for the next patch, use a local variable to represent
the sector size. No functional change.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
According to latest errata of J721e [1], HS400 mode is not supported
in MMCSD0 subsystem (i2024) and SDR104 mode is not supported in MMCSD1/2
subsystems (i2090). Therefore, replace mmc-hs400-1_8v with mmc-hs200-1_8v
in MMCSD0 subsystem and add a sdhci mask to disable SDR104 speed mode.
Also, update the itap delay values for all the MMCSD subsystems according
the latest J721e data sheet[2]
[1] - https://www.ti.com/lit/er/sprz455/sprz455.pdf
[2] - https://www.ti.com/lit/ds/symlink/tda4vm.pdf
Fixes: 70e167495a ("arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This adds support for devices with R40 dual rank DRAM, and asymmetric
A64 DRAM devices like the Pinephone/3GB.
Also we enable automatic gzipped kernel support, and allow scripted
DT overlay support. The rest of the patches are cleanups, but also
some sunxi-specific preparatory patches for USB3.0 and improved HDMI
support. The bulk of those changes will go through other trees, though.
Build-tested for all 156 sunxi boards, and boot tested on a A64, A20, R40,
H5, H6 and H616 board. USB, SD card, eMMC, HDMI and Ethernet all work
there (where applicable), with the exception of Ethernet on the H5. Since
this is already broken in v2021.04, I will send a separate fix.
Currently sunxi Makefile manually specifies full path to dw-hdmi common
code. However, that is not needed because it can be selected in Kconfig
instead.
Select proper symbol in Kconfig and drop path from Makefile.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The "booti" command to load arm64 Linux kernels supports automatic
decompression of zipped kernel images, but relies on some environment
variables to point to usable buffer RAM.
Add those variables and let them point to some default values, that
should cover most use-cases.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The FIT description has access to the configuration variables. Use the
appropriate variable instead of hardcoding the address.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
binman can fill in the default FIT configuration index as selected by
the "default-dt" argument, which is set to CONFIG_DEFAULT_DEVICE_TREE.
Let's respect the user's configuration by taking advantage of this
feature, instead of always defaulting to the first device tree in
CONFIG_OF_LIST.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The XHCI controller has its own clock and reset. Add them.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The 32kHz clock ("LOSC") on sunxi SoCs is provided by the RTC. It is
used, among other things, by the XHCI controller in the H6. To be able
to call clk_get_bulk() on the XHCI controller, some device needs to
provide all referenced clocks.
Since LOSC is a fixed-rate always-on clock, implementation is trivial.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Previously we do not have proper dual rank memory detection on R40
(because we omitted PIR_QSGATE, which does not work on R40 with our
configuration), and dual rank memory is just simply disabled as early
R40 boards available (Banana Pi M2 Ultra and Berry) have single rank
memory.
As a board with dual rank memory (Forlinx OKA40i-C) is now known to us,
we need to have a way to do memory rank detection to support that board.
Add some routine to detect memory rank by trying to access the memory
in rank 1 and check for error status of the memory controller, and then
enable dual rank memory on R40.
Similar routine can be used to detect half DQ width (which is also
detected by PIR_QSGATE on other SoCs), but it's left unimplemented
because there's no known R40 board with half DQ width now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: Move R40 detect code call into sunxi_dram_init()]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Previously we have known that R40 has a configuration register for its
rank 1, which allows different configuration than rank 0. Reverse
engineering of newest libdram of A64 from Allwinner shows that A64 has
this register too. It's bit 0 (which enables dual rank in rank 0
configuration register) means a dedicated rank size setup is used for
rank 1.
Now, Pine64 scheduled to use a 3GiB LPDDR3 DRAM chip (which has 2GiB
rank 0 and 1GiB rank 1) on PinePhone, that makes asymmetric dual rank
DRAM support necessary.
Add this support. The code could support both A64 and R40, but because
dual rank detection is broken on R40 now, we cannot really use it on R40
currently.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Commit 69076dff22 ("cmd: pxe: add support for FDT overlays") added
support for loading DT overlay files to PXE boot. However, it needs
additional environment variable which points to memory location which
can be used to temporary store overlay data.
Add it and in the process unify alignment using spaces and fix comment.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
update ls1028aqds networking protocol, config in ls1021atwr, env in ls1012a
Add seli3 board support, booke watchdog, update eTSEC support in ppc-qemu
Add DM_SERIAL and lpuart in sl28, add DM_ETH support for some of powerpc platforms
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- Minor fix to Apollo Lake devicetree bindings for FSP
- Refactor Designware PCIe drivers to core and SoC parts
- Add Amlogic Meson Designware PCIe controller driver
Add the FMan v3 nodes for the T1042D4RDB. The nodes are copied over with
little modification from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 FMan v3 device tree nodes for the T1042 SoC.
The device tree nodes are copied over with little modification
from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When two FMan's are present on a board, the MDIO nodes are found at the
same offsets inside each FMan. This causes "non unique device name"
errors when registering the MDIO nodes under the second FMan. Fix this
by updating the offsets of the MDIO nodes to include the parent FMan's
offset.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the FMan v3 nodes for the T4240RDB. The nodes are copied over with
little modification from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 FMan v3 device tree nodes for the T4240 SoC.
The device tree nodes are copied over with little modification
from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Disable the FMan mEMAC 5 and 6 nodes from the fdt since they are not
available under the supported RCW. Also disable the associated
"fsl,dpa-ethernet" nodes that reference them.
This is a simplified version of the fdt_fixup_fman_ethernet call for
use under DM_ETH.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the FMan v3 nodes for the T2080RDB. The nodes are copied over with
little modification from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 FMan v3 device tree nodes for the T2080 SoC.
The device tree nodes are copied over with little modification from
the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
scan_dev_for_efi is supposed to be called from scan_dev_for_boot.
However, this call is missing for ls1012a boards. As a result EFI
boot doesn’t work. Fix this issue by removing custom definition of
scan_dev_for_boot and use the default definition instead.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
