add support for printing various clock frequency info found
in SOC such as ARM core frequency, DSP core frequency and DDR
frequency as part of bdinfo command.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
remove the macro CONFIG_DISPLAY_CPUINFO as it is no longer
required. This is because clock info will be printed as part
'bdinfo' command and also remove support print_cpuinfo() as it will
no longer be called.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
For ARM systems, before ELF relocation was introduced,
CONFIG_SKIP_RELOCATE_UBOOT coul be used to prevent *COPYING* the
U-Boot image from whereever it was loaded to it's link address
(CONFIG_SYS_TEXT_BASE). The name was badly chosen, as no relocation
was performed at all, it was just a memcpy().
With ELF relocation, this does not work like that any more, and
related boards need to be fixed anyway. So don't keep this relict any
longer.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.
No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Davinci: Configurable NAND chip selects
Add a CONFIG_SYS_NAND_CS setting to all davinci configs and
use it to setup the NAND controller in the davinci_nand
mtd driver.
Signed-off-by: Nick Thompson <nick.thompson@gefanuc.com>
There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
defines.
Signed-off-by: Heiko Schocher <hs@denx.de>
Adding the CONFIG_SYS_64BIT_VSPRINTF in the DM355 EVM config.
Without this option enabled while performing NAND operations we will get
wrong diagnostic messages.
Example if the MTD NAND driver find a bad block while erasing from
a certain address, it will say bad block skipped at 0x00000000.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch does the following
1) Enables the NAND driver which is now available.
2) Enables the 'CONFIG_MTD_DEVICE' as without this the
compilation will fail
3) We now have a safe place to store environment and defines
an offset where this can be stored. This offset value is such that it is after
the location where U-Boot is flashed using TI flash utilities.
4) Enables Bootdelay
5) Increases malloc() arena size. Manufacturers are coming out with
NAND with large blocks sizes of upto 1 MiB. It has been noticed that
as the block size of the NAND used is increased, if this particular
value is not increased, the NAND driver will output out of memory
errors.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch removes the asm/sizes.h header file from being
included in the DaVinci SOC configs.
References to SZ_xx have been replaced by appropriate
bit shifted values.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Initial U-Boot support for the DaVinci DM355 EVM. This is a board
from Spectrum Digital. Board docs include schematic and firmware
for its microcontroller:
http://c6000.spectrumdigital.com/evmdm355/revd/
Most of the DM355 chip is fully documented by TI, the most notable
exception being the MPEG/JPEG coprocessor (programmable using codecs
available at no cost from TI), which is omitted from its DM335 sibling:
http://focus.ti.com/docs/prod/folders/print/tms320dm355.html
This version can boot from the on-board DM9000 Ethernet chip, after
being loaded (from NAND, MMC/SD, or UART). In the near future, NAND
and USB support could be added ... NAND support is being held back
until the support for the 4-bit ECC hardware is ready.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
