The ChromeOS EC keyboard is used by various different chromebooks. Peach
pi being the third board in the u-boot tree to use it (snow and peach
pit the other two). Rather then embedding the same big DT node in the
peach-pi DT again, copy the dtsi snippit & bindings documentation from
linux and include it in all 3 boards.
This slightly changes the dt bindings in u-boot:
* google,key-rows becomes keypad,num-rows
* google,key-colums becomes keypad,num-colums
* google,repeat-delay-ms and google,repeat-rate-ms are no longer used
and replaced by hardcoded values (similar to tegra kbc)
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
drivers/misc/i2c_eeprom.c fails to build unless CONFIG_FIT_SIGNATURE
is defined.
CC drivers/misc/i2c_eeprom.o
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_read':
drivers/misc/i2c_eeprom.c:15:10: error: 'ENODEV' undeclared
(first use in this function)
drivers/misc/i2c_eeprom.c:15:10: note: each undeclared identifier
is reported only once for each function it appears in
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_write':
drivers/misc/i2c_eeprom.c:21:10: error: 'ENODEV' undeclared
(first use in this function)
drivers/misc/i2c_eeprom.c:22:1: warning: control reaches end of
non-void function [-Wreturn-type]
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_read':
drivers/misc/i2c_eeprom.c:16:1: warning: control reaches end of
non-void function [-Wreturn-type]
make[2]: *** [drivers/misc/i2c_eeprom.o] Error 1
make[1]: *** [drivers/misc] Error 2
make: *** [drivers] Error 2
By the way, Sandbox (enabling CONFIG_FIT_SIGNATURE) is luckily
working depending on it.
Sandbox includes include/asm-generic/errno.h
from include/errno.h
from include/u-boot/rsa-checksum.h
from include/image.h
from include/common.h
from drivers/misc/i2c_eeprom.c
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
To enjoy driver-model on sandbox, using device tree is recommended.
While we are here, change sandbox_config to sandbox_defconfig too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
When watchdog is enabled, memmove_wd() always copy chunk up from small address.
This damanges overlapped memory data if destination address is smaller than
source address.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Simon Glass <sjg@chromium.org>
"err" was an unsigned variable, causing negative error codes to turn
into positive values, which are interpreted as an amount of succesfully
corrected bitflips (and thus not an error).
In particular, this resulted in that if the elm reports uncorrectable
errors (-EBADMSG), the MTD layer (and UBI) falsely succeeded.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix various spelling and grammatical errors in the README.
Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
pci ports are used as root complex in Linux. So set this as default
in u-boot for keystone devices
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
NFS is useful for loading zImage and dts through
NFS export. It saves us from running two services
for loading files over the network (tftp and nfs).
Signed-off-by: Felipe Balbi <balbi@ti.com>
On OMAP platforms (like OMAP5) Linux kernel fails to detect a SATA
device if it is used by U-Boot.
It happens because U-Boot does not reset SATA controller before boot.
Reset the controller on OS boot so that Linux will have a clean state
to work with.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
This allow the platform to handle a custom reset sequence.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Extract controller reset code from ahci_host_init() into separate
ahci_reset().
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Add defines to use CONFIG_SYS_GENERIC_BOARD and CONFIG_OF_LIBFDT.
Semi-separate to this: the size of the image for the da850evm has
increased to the point that the size in da850evm.h and the offset for
the environment in SPI flash no longer work. They are modified to
account for the larger image size.
Signed-off-by: Peter Howard <phoward@gme.net.au>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
The present fat implementation ignores FAT16 long name
directory entries which aren't placed in a single sector.
This was becouse of the buffer was always filled by the
two sectors, and the loop was made also for two sectors.
If some file long name entries are stored in two sectors,
the we have two cases:
Case 1:
Both of sectors are in the buffer - all required data
for long file name is in the buffer.
- Read OK!
Case 2:
The current directory entry is placed at the end of the
second buffered sector. And the next entries are placed
in a sector which is not buffered yet. Then two next
sectors are buffered and the mentioned entry is ignored.
- Read fail!
This commit fixes this issue by:
- read two sectors after loop on each single is done
- keep the last used sector as a first in the buffer
before the read of two next
The commit doesn't affects the fat32 imlementation,
which works good as previous.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Mikhail Zolotaryov <lebon@lebon.org.ua>
Cc: Tom Rini <trini@ti.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Suriyan Ramasami <suriyan.r@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
Tested-by: Simon Glass <sjg@chomium.org>
Enable UUID and partition support for scripted handling platforms with
MMC and eMMC and varied partitioning schemes
And remove it from headers that end up redefining it.
Signed-off-by: Nishanth Menon <nm@ti.com>
Part of DMM logic is reuse from commit
47a4bea6af ("ARM: omap4: Update sdram
setting for panda rev A6") Which broke SDP4430 with ES2.3 (uses old
DDR).
So, to maintain support for newer DDR used in Panda ES rev B3, we
should, in addition to the commit
675cc77a3a ("ARM:OMAP4+: panda-es: Support
Rev B3 Elpida DDR2 RAM"), DDR timings, also do DMM configuration
specific to Panda.
Signed-off-by: Nishanth Menon <nm@ti.com>
The gd will be cleared at first so we don't need to set arch.tbl to 0.
In addition, the checks later against lastinc also work fine with an
initial value of 0 here. This also brings us in line with sunxi code
for example.
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In both SPL and non-SPL cases we will make a call to timer_init() early
on and do not need to call it again within s_init().
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The save_boot_params function here is the same as the default weak one
from arch/arm/cpu/armv7/start.S, drop.
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Instead of setting working_fdt to map_sysmem(addr) (e.g. blob), it should be set
to addr directly as inside set_working_fdt_addr it uses map_sysmem(addr) again.
To test: ./u-boot -d dts/dt.bin , then issue: fdt addr 0x100, fdt print will
then cause an segmentation fault. After this fix fdt print is functional.
Commit 8bc347e2ec "ARM: bootm: Allow booting in secure mode on hyp capable
systems" added the capability to select nonsec vs sec mode boot via an
environment var.
There is a subtle gotcha with this functionality, which is that the PSCI nodes
are still created in the fdt (via armv7_update_dt->fdt_psci) even when booting
in secure mode. Which means that if the kernel is PSCI aware then it will fail
to boot because it will try and do PSCI from secure world, which won't work.
This likely didn't get noticed before because the original purpose was to
support booting the legacy linux-sunxi kernels which don't understand PSCI.
To fix expose boot_nonsec (renaming with armv7_ prefix) outside of bootm.c and
use from the virt-dt code.
As well as avoiding the creation of the PSCI nodes we should also avoid
reserving the secure RAM, so do so.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
For all flavours of ARC we execute the same code in "bdinfo" so we may
safely check for CONFIG_ARC. This is especially important since we're
about to add more types of ARC so existing check won't work in all
cases.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
All the MPC824X boards are still non-generic boards:
A3000, CPC45, CU824, eXalion, MVBLUE, MUSENKI, Sandpoint824x, utx8245
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Josef Wagner <Wagner@Microsys.de>
Cc: Torsten Demke <torsten.demke@fci.com>
Cc: Jim Thompson <jim@musenki.com>
Cc: Greg Allen <gallen@arlut.utexas.edu>
These boards are still non-generic boards.
drivers/rtc/ds12887.c should also be removed because it can not
be built without CONFIG_ATC.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
This board is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>
This board is still a non-generic board.
Unused code in arch/powerpc/cpu/mpc8xx/video.c should be also deleted
because CONFIG_VIDEO_ENCODER_AD7176, CONFIG_VIDEO_ENCODER_AD7177,
CONFIG_VIDEO_ENCODER_AD7179 are not defined any more.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
