In the draco CPU board family, etamin is a new variant
with bigger flash and more RAM. Due to new flash that
uses larger pages (4K) some changes are necessary because
it impacts the MTD partition layout and the ubi mount
parameters.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Move BOOTDELAY into defconfig, just always be 3 now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable Spread Spectrum for the MPU by calculating the required
values and setting the registers accordingly.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
add missing CM_CLKMODE_DPLL_SSC_ACK_MASK,
CM_CLKMODE_DPLL_SSC_DOWNSPREAD_MASK and
CM_CLKMODE_DPLL_SSC_TYPE_MASK
defines. Used for enabling spread spectrum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
I noticed secondary CPUs sometimes fail to wake up, and the root
cause is that the sev instruction wakes up slave CPUs before the
preceding the register write is observed by them.
The read-back of the accessed register does not guarantee the order.
In order to ensure the order between the register write and the sev
instruction, a dsb instruction should be executed prior to the sev.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This code auto-detects the best-match FDT file name, but it should
respect the user's choice if "fdt_file" environment is found in a
saved set of environments.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This function is shared between PH1-LD11 and PH1-LD20. The difference
is the boot-mode latch for the USB boot mode.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Boot ROM on PH1-LD11/LD20 exports built-in APIs to load images
from an eMMC device. They are useful to reduce the memory footprint
of SPL, rather than compiling the whole MMC framework.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some SPL loaders (like Allwinner's boot0, and Broadcom's boot0)
require a header before the actual U-Boot binary to both check its
validity and to find other data to load. Sometimes this header may
only be a few bytes of information, and sometimes this might simply
be space that needs to be reserved for a post-processing tool.
Introduce a config option to allow assembler preprocessor commands
to be inserted into the code at the appropriate location; typical
assembler preprocessor commands might be:
.space 1000
.word 0x12345678
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Commit Notes:
Please note that the current code:
start.S (arm64) and
vectors.S (arm)
already jumps over some portion of data already, so this option basically
just increases the size of this region (and the resulting binary).
For use with Allwinner's boot0 blob there is a tool called boot0img[1],
which fills the header to allow booting A64 based boards.
For the Pine64 we need a 1536 byte header (including the branch
instruction) at the moment, so we add this to the defconfig.
[1] https://github.com/apritzel/pine64/tree/master/tools
END
Reviewed-by: Tom Rini <trini@konsulko.com>
To quit an EFI application we will need logic to jump to the caller
of a function without returning from the function we called into,
so we need setjmp/longjmp functionality.
This patch introduces a trivial implementation of these that I
verified works on armv7, thumb2 and aarch64.
Signed-off-by: Alexander Graf <agraf@suse.de>
QorIQ LS1012A FREEDOM (LS1012AFRDM) is a high-performance
development platform, with a complete debugging environment.
The LS1012AFRDM board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QorIQ LS1012A Development System (LS1012AQDS) is a high-performance
development platform, with a complete debugging environment.
The LS1012AQDS board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
This patch add support of LS1012A SoC along with
- Update platform & DDR clock read logic as per SVR
- Define MMDC controller register set.
- Update LUT base address for PCIe
- Avoid L3 platform cache compilation
- Update USB address, errata
- SerDes table
- Added CSU IDs for SDHC2, SAI-1 to SAI-4
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Makarand Pawagi <makarand.pawagi@mindspeed.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SoC overviews are getting repeated across board folders.
So, Organize SoC overview at common location i.e. fsl-layerscape/doc
Also move README.lsch2 and README.lsch3 in same folder.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_speed.c: In function
‘get_sys_info’:
arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_speed.c:29:6: warning:
unused variable ‘rcw_tmp’ [-Wunused-variable]
u32 rcw_tmp;
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Other than LS1043A, LS1012A also Chassis Gen2 Architecture compliant.
So Avoid LS1043A specific defines in arch/arm
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
It is not mandatory for Layerscape SoCs to have SMMU. SoCs like
LS1012A are layerscape SoC without SMMU IP.
So put SMMU configuration code under SMMU_BASE.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
With the existing code, function symbols are defined in .text, and the
body is defined in .text.xxx. This causes (at least some version of) the
linker not to emit the function body into the final binary, since it's
part of a different section to the symbols being referenced. This of
course causes a wide variety of failures.
This change moves the push/pop-section directives before the function
symbols, and after any relate ENDPROC macro invocations, so that symbols
and bodies are all in the "pushed" sections, and thus the function bodies
are emitted into the binary.
This solves (at least) the boot problems currently seen on Tegra systems
that use SPL (i.e. all ARMv7 Tegras).
Fixes: 13b0a91a6d ("arm: lib: Split asm symbols into different .text subsections")
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
BOOTCFG_RSTMUX8 register controls the reset mux associated with the ARM.
Timer5(dedicated to ARM) when used as WatchDog timer, the events it
generates are routed to the above mux.
Following are the 3 events that can controlled bt the reset mux:
- Device Reset
- An interrupt to the ARM_GIC
- An interrupt to the ARM_GIC followed by a device reset.
Right now to give a default watchdog behaviour "Device reset" is
being selected.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
The pmic registers for variants of am57xx boards are different
hence we need to assign them carefully based on the board type.
Add a function to assign omap_vcores after the board detection.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Define specific macros for the voltage values for all voltage
domains for all applicable OPPs - OPP_NOM, OPP_OD and OPP_HIGH.
No separate macros are defined for VD_MPU and VD_CORE at OPP_OD
and OPP_HIGH as these use the same values as OPP_NOM.
The current macros will be used as common macros that can be
redefined appropriately based on a selected OPP configuration
at build time.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The voltage values for each voltage domain at an OPP is identical
across all the SoCs in the DRA7 family. The current code defines
one set of macros for DRA75x/DRA74x SoCs and another set for DRA72x
macros. Consolidate both these sets into a single set.
This is done so as to minimize the number of macros used when voltage
values will be added for other OPPs as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Define a set of common macros for the efuse register offsets
(different for each OPP) that are used to get the AVS Class 0
voltage values and ABB configuration values. Assign these
common macros to the register offsets for OPP_NOM by default
for all voltage domains. These common macros can then be
redefined properly to point to the OPP specific efuse register
offset based on the desired OPP to program a specific voltage
domain.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The current OPP_NOM voltage values defined for the MPU and CORE
voltage domains are based on the initial DRA75x_74x_SR1.1_DM data
manual. As per this DM, the PMIC boot voltage can be set to either
1.10V or 1.15V for VD_MPU, and either 1.06V or 1.15V for VD_CORE.
While the current values are correct, the latter set of values
are the values that are common across all DRA75x, DRA72x SoCs and
for all current Silicon revisions. So, update both the MPU and CORE
OPP_NOM voltages to 1.15V.
The macros are also slightly reorganized so that both the MPU and
CORE voltage domain values are defined together.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
CONFIG_USB_XHCI_OMAP is enabled for host mode independent of CONFIG_USB_DWC3
which is meant for gadget mode only. We need enable/disbale_usb_clocks() for
host mode as well so provide for it.
Fixes: 09cc14f4bc ("ARM: AM43xx: Add functions to enable and disable USB clocks"
Signed-off-by: Roger Quadros <rogerq@ti.com>
Split each symbol in lib1funcs into different .text.foo section instead
of placing all of them into plain .text . This allows the linker to collect
and discard unused assembler symbols.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Import functions into lib1funcs.S which are required for Thumb1
build. These functions come from gcc 5.3.1 release.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Import muldi3.S from Linux 4.4.6 , commit 0d1912303e54ed1b2a371be0bba51c384dd57326
on arm32. This file implements __aeabi_lmul and it's alias __muldi3, which
is needed when doing Thumb1 builds.
This patch also defines CONFIG_THUMB2_KERNEL and CONFIG_ARM_ASM_UNIFIED
which is necessary for correct build of these files both in ARM and
Thumb mode, just like Linux does.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Fix the following warning when building for thumb2 target by tweaking the
instruction syntax:
Warning: conditional infixes are deprecated in unified syntax
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Import __do_div64 from Linux 4.4.6 , commit 0d1912303e54ed1b2a371be0bba51c384dd57326
on arm32. This function is for some toolchains, which generate _udivmoddi4()
for 64 bit division.
Since we do not support stack unwinding, instead of importing the whole
asm/unwind.h and all the baggage, this patch defines empty UNWIND() macro.
This patch also defines CONFIG_THUMB2_KERNEL and CONFIG_ARM_ASM_UNIFIED
which is necessary for correct build of these files both in ARM and
Thumb mode, just like Linux does.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This assembler source won't build in Thumb2 mode, so fix it adding
the necessary Thumb2 conditional macros from unified.h .
This patch also defines CONFIG_THUMB2_KERNEL and CONFIG_ARM_ASM_UNIFIED
which is necessary for correct build of these files both in ARM and
Thumb mode, just like Linux does.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync the libgcc 32bit division and modulo operations with Linux 4.4.6 ,
commit 0d1912303e54ed1b2a371be0bba51c384dd57326 . The functions in these
four files are present in lib1funcs.S in Linux, so replace these files
with lib1funcs.S from Linux.
Since we do not support stack unwinding, instead of importing the whole
asm/unwind.h and all the baggage, this patch defines empty UNWIND() macro
in lib1funcs.S . Moreover, to make all of the functions available, define
CONFIG_AEABI , which is safe, because U-Boot is always compiled with ARM
EABI.
This patch also defines CONFIG_THUMB2_KERNEL and CONFIG_ARM_ASM_UNIFIED
which is necessary for correct build of these files both in ARM and
Thumb mode, just like Linux does.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync the libgcc shift operations with Linux kernel 4.4.6 , commit
0d1912303e54ed1b2a371be0bba51c384dd57326 . Syncing these three
files is easy, as there is almost no change in them, except the
addition of Thumb support.
This patch also defines CONFIG_THUMB2_KERNEL and CONFIG_ARM_ASM_UNIFIED
which is necessary for correct build of these files both in ARM and
Thumb mode, just like Linux does.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Drop the underscore from the filenames of files implementing libgcc
routines. There is no functional change. This change is done to make
sync with Linux kernel easier.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
