On J721e R5 SPL, dfu buffer for loading sysfw.itb image gets allocated
before DRAM gets initialized. So, the buffer gets allocated in MCU L3
RAM. The current buffer size to be allocated is 256KB and the available
total heap memory is 0x70000 (448KB). This leads to NOMEM errors during
allocation.
In other cases when constraints such as above are not present fix the size
of buffers to the sector size in OSPI for proper functioning.
Also, if CONFIG_SYS_DFU_DATA_BUF_SIZE is defined and
CONFIG_SYS_DFU_MAX_FILE_SIZE is not defined then the max file size for dfu
transfer is defined as CONFIG_SYS_DFU_DATA_BUF_SIZE.
Fix these by setting appropriate buffer sizes in their respective defconfig
files and defining the max file size as 8 MB which is the default dfu
buffer size.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add CONFIG_PREBOOT to provide an automatic and easier way
to configure ethernet PHY before loading the firmware.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-19-kishon@ti.com
Add config for torrent serdes and common clock framework.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-17-kishon@ti.com
Add configs to support UHS modes for the SD card and HS200 for the eMMC.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
By default CONFIG_LOGLEVEL seems to be set to 4 which is
too low and doesn't show dev_info/dev_notice/dev_warn
messages on console. This has been deliberately set low
globally to be conservative setting across the board due to
primary bootloader size limitations. It is best to tune
per board config as per user needs.
On K3 we have separate SPL and u-boot configs so we
can afford to set u-boot CONFIG_LOGLEVEL to 7.
On AM65 this patch causes u-boot.img size to change from
932KB to 940KB with 1 line additional print during
MMC boot. i.e. details of Net subsystem
"Net: K3 CPSW: nuss_ver: 0x6BA00102 cpsw_ver: 0x6BA80102 ale_ver: 0x00293904 Ports:1 mdio_freq:1000000"
Similar 8KB difference was seen on J721E.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
The A72 U-boot can support early booting of any of the Main or MCU R5F
remote processors from U-boot prompt to achieve various system usecases
before booting the Linux kernel. Update the default BOOTCOMMAND to provide
an automatic and easier way to start various remote processors through
added environment variables.
Signed-off-by: Suman Anna <s-anna@ti.com>
The J7200 SoCs has two R5F sub-systems. Enable the TI K3
R5F remoteproc driver and the remoteproc command options
to allow these R5F processors to be booted from A72 U-Boot.
The Kconfigs are added using savedefconfig.
Signed-off-by: Suman Anna <s-anna@ti.com>
Enable configs required to support HyperFlash boot and detection of
onboard mux switch for HyperFlash selection
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
