fatload/ext2load both require that the device and partition be
specified after specifying the device type. Specify the first
partition on mmc device 0, which is the only mmc device currently
configured on the pandora.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Grazvydas Ignotas <notasas@gmail.com>
On all TI platforms the ROM defines a "downloaded image" area at or near
the start of SRAM which is followed by a reserved area. As it is at
best bad form and at worst possibly harmful in corner cases to write in
this reserved area, we stop doing that by adding in the define
NON_SECURE_SRAM_IMG_END to say where the end of the downloaded image
area is and make SRAM_SCRATCH_SPACE_ADDR be one kilobyte before this.
At current we define the end of scratch space at 0x228 bytes past the
start of scratch space this this gives us a lot of room to grow. As
these scratch uses are non-optional today, all targets are modified to
respect this boundary.
Tested on OMAP4 Pandaboard, OMAP3 Beagle xM
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Thomas Weber <weber@corscience.de>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Ben Whitten <ben.whitten@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: "B, Ravi" <ravibabu@ti.com>
Cc: "Matwey V. Kornilov" <matwey.kornilov@gmail.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Ash Charles <ashcharles@gmail.com>
Cc: "Kipisz, Steven" <s-kipisz2@ti.com>
Cc: Daniel Allred <d-allred@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
The PBIAS fixing is done in the MMC driver, and doing it in the
the board file conflicts with the driver causing intermittent
hangs on reboot. Remove this from the board file and let
the driver do it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
All of the command files have moved to cmd directory, add description to
Directory Hierarchy.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sometimes boards may need more time to become stable network connection
due to several reasons:
- phy speed
- link-partner (switch)
Therefore we increase the retry-count to 10 for making sure that network
connection works always.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
An issue in the TI secure image generation tool causes the ROM to
load the SPL at a different load address than what is specified by
CONFIG_ISW_ENTRY_ADDR while doing a peripheral boot on HS devices.
This causes the SPL to fail on secure devices during peripheral
boot.
The TI secure image generation tool has been fixed so that the SPL
will always be loaded at 0x403018E0 by the ROM code for both
peripheral and memory boot modes.
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable the platform-specific post-processing of FIT-extracted blobs such
as Kernel, DTB, and initramfs on TI AM57xx high-security (HS) devices
which will ultimately invoke a ROM-based API call that performs secure
processing such as blob authentication.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable the platform-specific post-processing of FIT-extracted blobs such
as Kernel, DTB, and initramfs on TI DRA7xx high-security (HS) devices
which will ultimately invoke a ROM-based API call that performs secure
processing such as blob authentication.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable the platform-specific post-processing of FIT-extracted blobs such
as Kernel, DTB, and initramfs on TI AM43xx high-security (HS) devices
which will ultimately invoke a ROM-based API call that performs secure
processing such as blob authentication.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This reworks spl_set_header_raw_uboot to allow having both os boot
(which comes with a valid header) and aborting when no valid header is
found (thus excluding raw u-boot.bin images).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
When enabling a fixed regulator, it may take some time to rise to the
correct voltage. If we do not delay here then subsequent operations
will fail.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Prior to this commit, the tool could not move options guarded by
CONFIG_SPL_BUILD ifdef conditionals because they do not show up in
include/autoconf.mk. This new option, if given, makes the tool
parse spl/include/autoconf.mk instead of include/autoconf.mk,
which is probably preferred behavior when moving options for SPL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently, the tool gives up moving an option quietly if its entry
was not found in Kconfig.
If the option is not defined in the config header in the first
place, it is no problem (as the Kconfig entry may have been hidden
by reasonable "depends on").
However, if the option is defined in the config header, the missing
Kconfig entry is a sign of possible behavior change. It is highly
recommended to manually check if the option has been moved as
expected. In this case, let's add "suspicious" in the log and
change the log color (if --color option is given) to make it stand
out.
This was suggested by Tom in [1].
[1] http://lists.denx.de/pipermail/u-boot/2016-July/261988.html
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The sets feature is handier for adding unique elements.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since commit cc008299f8 ("tools: moveconfig: do not rely on type
and default value given by users"), we do not have this error case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Remove the device definition from board file, update the driver with
the new compatible property and update config with necessary options.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a pin controller driver for Meson GXBB adapted from Linux kernel.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Import DTS files and dt-bindings includes from Linux 4.8-rc1.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In cases where the pins and groups definitions are in a sub-node, as:
uart_a {
mux {
groups = "uart_tx_a", "uart_rx_a";
function = "uart_a";
};
};
pinctrl_generic_set_state_subnode() returns an error for the top-level
node and pinctrl_generic_set_state() fails. Instead, return success so
that the child nodes are tried.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 62afc60188 introduced fpga image load via
bootm but broke the OS check in fit_image_load().
This commit removes following compiler warning:
---8<---
In file included from tools/common/image-fit.c:1:
/Volumes/devel/u-boot/tools/../common/image-fit.c:1715:39: warning: use of logical '||' with constant operand [-Wconstant-logical-operand]
os_ok = image_type == IH_TYPE_FLATDT || IH_TYPE_FPGA ||
^ ~~~~~~~~~~~~
/Volumes/devel/u-boot/tools/../common/image-fit.c:1715:39: note: use '|' for a bitwise operation
os_ok = image_type == IH_TYPE_FLATDT || IH_TYPE_FPGA ||
^~
|
1 warning generated.
--->8---
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
On the raspberry pi, you can disable the serial port to gain dynamic frequency
scaling which can get handy at times.
However, in such a configuration the serial controller gets its rx queue filled
up with zero bytes which then happily get transmitted on to whoever calls
getc() today.
This patch adds detection logic for that case by checking whether the RX pin is
mapped to GPIO15 and disables the mini uart if it is not mapped properly.
That way we can leave the driver enabled in the tree and can determine during
runtime whether serial is usable or not, having a single binary that allows for
uart and non-uart operation.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
So far we could only tell the gpio framework that a GPIO was mapped as input or
output, not as alternative function.
This patch adds support for determining whether a function is mapped as
alternative.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
With commit ceec08f50b, phy is connected to slave 0, but
changing the phy node was missed, fix it by populating the
phy node to proper cpsw slave node.
Fixes: ceec08f50b ("ARM: dts: dra72-evm: Add mode-gpios entry for mac node")
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Vignesh R <vigneshr@ti.com>
Tested-by: Tom Rini <trini@konsulko.com>
Casting "int"s to pointers is only valid for 32-bit systems.
Add the appropriate pointer type cast to avoid a compiler warning
when compiling for AArch64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
There is no "CONFIG_MACH_SUN50I_A64" in upstream U-Boot, so fix
the name to prevent the option to be enabled.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This commit moved the SPL stack into SRAM C, which worked when the SPL
set the AHB1 clock down to 100 MHz to cope with the flaky SRAM C access
from the CPU.
However booting with boot0 (and thus not using SPL at all) we still run
with a 200 MHz AHB1, so any access to SRAM C is prone to fail.
Since this commit does _not_ only affect the SPL code, but also the
U-Boot proper, we fail when booting with boot0.
As the introduction of tiny-printf reduced the size of the SPL, we
can afford to have the SPL stack in SRAM A1.
This reverts commit 1a83fb4a17
and fixes booting the Pine64 when using boot0.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Orange Pi Plus2E is an extended version of the Orange Pi Pc Plus,
with 2G RAM and an external gbit ethernet phy.
The dts file is identical to the one submitted to the upstream kernel,
except that it has the pending patch to enable the ethernet controller
squashed in, as u-boot already has sun8i-emac support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This adds an emac node to the orangepi-2 dts (not yet merged upstream,
but in u-boot we already have emac support); fixes the alphetically
sorting of nodes in sun8i-h3-orangepi-plus.dts and disables some
usb controllers in sun8i-h3-orangepi-plus.dts which are only used
on the plus2e, as upstream has decided to do a separate dts files
for the plus2e.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The sun8i-emac driver follows an old version of the proposed DT
bindings, where the EMAC clock and EPHY control register range is
listed directly, rather than through a syscon phandle.
Add back the syscon register range to avoid an invalid data access.
We should fix the driver once the Linux kernel bindings have been
finalized.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
A33-OLinuXino is A33 development board designed by Olimex LTD.
It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.
It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.
The dts files are identical to the ones submitted to the upstream kernel.
Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The iNet D978 rev2 is a tablet board designed by iNet, which is intended to
use on 10" tablets with a appearance like Apple iPad. It has A33 SoC, 1GB
RAM, 8GB/16GB NAND, SDIO Wi-Fi, a MicroUSB port and a MicroSD slot.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a proper dts for the iNet D978 rev2 based A33 tablets.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that nand_info[] is an array of pointers we need to test the
pointer itself rather than using name as a proxy for NULLness.
Fixes: b616d9b0a7 ("nand: Embed mtd_info in struct nand_chip")
Signed-off-by: Scott Wood <oss@buserror.net>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Looks like we have few more places where we're testing for
nand_info[i]->name. We can now use just test for nand_info[i]
instead.
This fixes a data abort on devices with no NAND when doing
nand info.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In commit 17cb4b8f32 ("mtd: nand: Add+use mtd_to/from_nand and
nand_get/set_controller_data") the assignment of mtd->priv was removed
but was not replaced. This adds the required nand_set_controller_data()
call.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
The Colorado TK1 SOM is a small form factor board similar to the
Jetson TK1. The main differences lie in the pinmux, and in that the
PCIe controller is set to use in 4lanes+1lane, rather than 2+2.
The pinmux header here was generated from a spreadsheet provided by
Colorado Engineering using the tegra-pinmux scripts. The spreadsheet
was converted from v09 to v11 by me.
Signed-off-by: Peter Chubb <peter.chubb@data61.csiro.au>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The board ID EEPROM and board ID stickers on p2771-0000 will use a numeric
versioning scheme, with version numbers such as 000/100/200/300/400/500.
Within NVIDIA, these versions are also known as A00/A01/A02/A03/A04/B00.
However, that numbering scheme is not easily visible outside of NVIDIA,
and so does not make much sense to use. Convert U-Boot to use the readily
visible numeric scheme.
Also, it turns out that the current A02 DT actually applies to board
versions 000/100/200 (A00..A02). Consequently rename this to 000 not 200
so that all U-Boot builds are named after the first version of the HW they
support.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This introduces two board defconfig files for generating EFI 32-bit
and 64-bit payloads, to run on QEMU x86 target.
With these in place, hopefully buildman will catch any build error
with EFI payload support on x86.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are lots of warnings when building EFI 64-bit payload.
include/asm-generic/bitops/__fls.h:17:2:
warning: left shift count >= width of type
if (!(word & (~0ul << 32))) {
^
In fact, U-Boot itself as EFI payload is running in 32-bit mode.
So BITS_PER_LONG needs to still be 32, but EFI status codes are
64-bit when booting from 64-bit EFI. Introduce EFI_BITS_PER_LONG
to bridge those status codes with U-Boot's BITS_PER_LONG.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 73c5c39 "Makefile: Drop unnecessary -dtb suffixes",
EFI payload does not build anymore. This fixes the build.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Generally the microcode is combined into a single block only (and removed
from the device tree) when there are multiple blocks. But this is not a
requirement.
Adjust the ivybridge code to avoid assuming this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a debug() at this point to help figure out what is wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher<hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This will be useful, for example, to load firmware to DRAM and make
it visible to other agents.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is very likely to be necessary for normal use cases.
Set its default to 'y' for shorter defconfig files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The eMMC on sLD3 is assigned with dedicated pins (only multiplexed
with GPIO), so it shouldn't hurt to enable eMMC on SPL all the time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
