Part of the SERDES9 erratum work-around is to set some bits in the SerDes
TTLCR0 register for lanes configured as XAUI, SGMII, SRIO, or AURORA. The
current code does this only for XAUI, so extend it to the other protocols.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The work-around for P4080 erratum SERDES-8 requires all lanes of banks two
and three to be disabled (powered down) in the RCW. Display a warning
message if this is not the case.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SerDes PLL bandwidth default setting is incorrect when no lanes are
configured as PCI Express.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A lot of boards set FT_FSL_PCI_SETUP directly in their board code
and don't check to see if CONFIG_PCI is actually defined. This
will cause the board compilation to fail if CONFIG_PCI is not
defined. The p1022ds board is one such example.
Instead of fixing every board this patch wraps FT_FSL_PCI_SETUP
around CONFIG_PCI so we can remove CONFIG_PCI and boards will
still build properly.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
versioned SEC properties changed names during development, so
for now search and update LIODNs for both "secX.Y" and
"sec-vX.Y" based properties.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The workaround for ESDHC111 should also be applied on
P2040/P3041/P5010/P5020 SoCs.
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P2040, P3041, P5010, and P5020 all have internal USB PHYs that we
need to enable for them to function.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P3041DS & P5020DS boards are almost identical (except for the
processor in them). Additionally they are based on the P4080DS board
design so we use the some board code for all 3 boards.
Some ngPIXIS (FPGA) registers where reserved on P4080DS and now have
meaning on P3041DS/P5020DS. We utilize some of these for SERDES clock
configuration.
Additionally, the P3041DS/P5020DS support NAND.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rework and add some new APIs to the fsl_corenet_serdes code for use by
erratum and drivers.
* Rename serdes_get_bank() to serdes_get_bank_by_lane()
* Add serdes_get_first_lane returns which SERDES lane is used by device
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix fdt bportal to pass the bman revision number to kernel via device tree.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To make sure that machine change operation work successfully, change
timing parameters first before changing machine for chip select on IFC.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If FB address is defined specific address then don't grab memory for LCD
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Move the header file and definitions of ftsmc020
static memory control unit from a320 SoC folder to
"drivers/mtd" folder.
This change will let other SoC which also use ftsmc020
could share the same header file.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Move the header file "ftsdmc020.h" (SDRAM Controller)
to "include/faraday" folder.
This change will let other SoC which also use ftsdmc020
could share the same header file.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Removed boot_flash_* extern variables.
boot_flash_type was totally unused. The other ones were actually constants, so
they have been replaced with #defines in the board config files.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Since addr_sp is a byte address, it should be adjusted by 12 here.
Signed-off-by: Eric Cooper <ecc@cmu.edu>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Wolfgang Denk <wd@denx.de>
CONFIG_OMAP34XX must be checked for existence, not value.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The reset sequence/configuration for ehci is highly board specific,
so this will be done in the source for the board, instead of
introducing several CONFIG_* which would be needed to make those
few lines in beagle.c usable across different OMAP boards.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Move the header file and definitions of fttmr010
power control unit from a320 SoC folder to
"include/faraday" folder.
This change will let other SoC which also use fttmr010
could share the same header file.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Add i2c_clk_enable in the cpu specific code, since previous platform it,
while new platform don't need. In the pantheon and armada100 platform,
this function is defined as NULL one.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
For better sharing with other platform other than pxa's,
it is more convenient to put the driver to the common place.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
ftpmu010 related code has been moved to drivers/power/.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
This allows the reading of EEPROMS on the expansion bus without adding
external pull-ups.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Drop warnings due to recent commit
ARM: mx31: Print the silicon version
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
factor out boot cause function to common code to avoid
the duplicate code in each board support package
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Commit 5d2c154 (IMX: MX31: Cleanup include files and drop nasty #ifdef in drivers)
renamed mx31-imx-regs.h to imx-regs.h.
Change the file label accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Use the same method of the Linux kernel to print the MX31 silicon version on
boot.
Tested on a MX31PDK with a 2.0 silicon, where it shows:
CPU: Freescale i.MX31 rev 2.0 at 531 MHz
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The patch add CONFIG_HW_WATCHDOG to be used
with the internal watchdog timer of the MX31
processor. Two function are exported for the
board maintainers:
mxc_hw_watchdog_enable
mxc_hw_watchdog_reset
The board maintainer can decide to use mxc_hw_watchdog_reset as
hw_watchdog_reset, or to implement his own function to reset
the watchdog.
The watchdog timer can be configured with CONFIG_SYS_WD_TIMER_SECS
(value in seconds). The MX31 allows values between 0.5
(CONFIG_SYS_WD_TIMER_SECS = 0) and 128 seconds.
Signed-off-by: Stefano Babic <sbabic@denx.de>
If a regions is reserved in the fdt, then it should not be used. Add
the memreserve regions to the lmb so that u-boot doesn't use them to
store the initrd.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The previous patch makes u-boot use the full accessible size of ram as
the default boot mapped size if CONFIG_SYS_BOOTMAPSZ is not defined,
which means boot_relocate_fdt() can be changed to depend solely on
CONFIG_OF_LIBFDT.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This patch adds a function getenv_bootm_mapsize() for obtaining the
size of the early mapped region accessible by the kernel during early
boot. It defaults to CONFIG_SYS_BOOTMAPSZ, or if not defined,
defaults to getenv_bootm_size(), which in turn defaults to the size of
RAM.
getenv_bootm_mapsize() can also be overridden with a "bootm_mapsize"
environmental variable.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
