The p2020DS, MPC8536DS, MPC8572DS, MPC8544DS boards are capable of
swizzling the upper address bits of the NOR flash we boot out of which
creates the concept of "virtual" banks. This is useful in that we can
flash a test of image of u-boot and reset to one of the virtual banks
while still maintaining a working image in "bank 0".
The PIXIS FPGA exposes registers on LBC which we can use to determine
which "bank" we are booting out of (as well as setting which bank to
boot out of).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8641HPCN board is capable of swizzling the upper address bit of
the NOR flash we boot out of which creates the concept of "virtual"
banks. This is useful in that we can flash a test of image of u-boot
and reset to one of the virtual banks while still maintaining a
working image in "bank 0".
The PIXIS FPGA exposes registers on LBC which we can use to determine
which "bank" we are booting out of (as well as setting which bank to
boot out of).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We have always mapped at least 16M in the kernel and we have seen cases
with new kernel features that a kernel image needs more than 8M of
memory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_SYS_MALLOC_LEN is defined in the board config, and
the keymile-common.h, which collects common options used
by all keymile-boards. This results in a compile error
when compiling the kmeter1 board. So remove this define
in the board config file.
Signed-off-by: Heiko Schocher <hs@denx.de>
- CONFIG_SYS_MAX_I2C_BUS changed to 1
We use only one I2C hardwarecontroller on this boards, so
change the CONFIG_SYS_MAX_I2C_BUS to 1.
- common: dont print errormsg if second IVM Block lacks.
- 82xx, mgcoge: fix double mtdpart entry in environment
- 82xx, mgcoge: activate on second Flash the second bank.
- common: CONFIG_ENV_SIZE 0x4000 for all keymile boards
- common: Change malloc size to 1MByte for all Keymile boards
We need a bigger malloc area for the environment support (128k)
on some Keymile boards (kmeter1) and the upcoming UBI support.
Change it to 1MB for all Keymile boards to be on the save side.
Also define CONFIG_SYS_64BIT_VSPRINTF which is needed for
UBI/UBIFS support.
- Add UBI support to all Keymile boards
- change manner of writing "/localbus/ranges" node
instead of writting the complete "/localbus/ranges" node
before booting Linux, only update the ranges entries
which gets dynamical detected (size of flashes).
This is needed, because keymile adds in the DTS
"/localbus/ranges" node entries, which u-boot must
not overwrite/delete.
- kmeter, mgcoge: define 2 seperate regions needed for the Intel P30 chips
The Intel P30 chip has 2 non-identical chips on
one die, so we need to define 2 seperate regions
that are scanned by physmap_of independantly.
- kmeter1: Add MTD concat support to Keymile boards
- 82xx, mgcoge: add "unlock=yes" to default environment
- added CONFIG_MTD_DEVICE to get in sync with mainline code
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds unaligned.h for ARM (needed to build with LZO
compression). The file is taken from the linux kernel, but includes
u-boot headers instead.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Acked-by: Stefan Roese <sr@denx.de>
Shove a lot of the HOSTCC and related #ifdef checking crap into the new
compiler.h header so that we can keep all other headers nice and clean.
Also introduce custom uswap functions so we don't have to rely on the non
standard implementations that a host may (or may not in the case of OS X)
provide. This allows mkimage to finally build cleanly on an OS X system.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Commit 2419169f removed support for legacy NAND and disk on chip but
missed to update the code for a few boards. This patch fixes the
resulting build issues.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds a SATA harddisk driver for the canyonlands.
This patch is kernel driver's porting.
This patch corresponded to not cmd_scsi but cmd_sata.
This patch divided an unused member with ifndef __U_BOOT__ in the structure.
[environment variable, boot script]
setenv bootargs root=/dev/sda7 rw
setenv bootargs ${bootargs} console=ttyS0,115200
ext2load sata 0:2 0x400000 /canyonlands/uImage
ext2load sata 0:2 0x800000 /canyonlands/canyonlands.dtb
fdt addr 0x800000 0x4000
bootm 0x400000 - 0x800000
If you drive SATA-2 disk on Canyonlands, you must change parts from
PI2PCIE212 to PI2PCIE2212 on U25. We confirmed to boot by using
following disks:
1.Vendor: Fujitsu Type: MHW2040BS
2.Vendor: Fujitsu Type: MHW2060BK
3.Vendor: HAGIWARA SYS-COM:HFD25S-032GT
4.Vendor: WesternDigital Type: WD3200BJKT (CONFIG_LBA48 required)
5.Vendor: WesternDigital Type: WD3200BEVT (CONFIG_LBA48 required)
6.Vendor: Hitachi Type: HTS543232L9A300 (CONFIG_LBA48 required)
7.Vendor: Seagate Type: ST31000333AS (CONFIG_LBA48 required)
8.Vendor: Transcend Type: TS32GSSD25S-M
9.Vendor: MTRON Type: MSD-SATA1525-016
Signed-off-by: Kazuaki Ichinohe <kazuichi at fsi.co.jp>
From: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
This patch adds support for the Tundra TSI148 VME-bridge. It's used on
the upcoming esd VME8349 board.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
While the 1.0 and 1.2 spin of the bf533-stamp boards can handle the higher
SCLK speeds just fine, the 1.1 spin cannot due to the bugs introduced with
the shortened SDRAM traces. So lower the SCLK speed down to a value that
all three can handle.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Part of the mini Blackfin ABI with operating systems is that they can use
0x4f0-0x4f8 to pass log buffers to/from bootloaders. So add support to
U-Boot for reading the log buffer.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Commit 8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but
failed to fix the affected boards.
This patch covers the non-PPC boards that were missed in the previous
patch (commit 170c1972).
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 8e55258f created function uec_standard_init() to initialize
all UEC interfaces for 83xx and 85xx but failed to provide a
prototype for it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but
failed to fix the affected boards.
Signed-off-by: Wolfgang Denk <wd@denx.de>
So far the console API uses the following naming convention:
======Extract======
typedef struct device_t;
int device_register (device_t * dev);
int devices_init (void);
int device_deregister(char *devname);
struct list_head* device_get_list(void);
device_t* device_get_by_name(char* name);
device_t* device_clone(device_t *dev);
=======
which is too generic and confusing.
Instead of using device_XX and device_t we change this
into stdio_XX and stdio_dev
This will also allow to add later a generic device mechanism in order
to have support for multiple devices and driver instances.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Edited commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
A bug was introduced by commit e94e460c6e
which affected non-MPC83xx/85xx/86xx ppc boards which had CONFIG_DDR_ECC
defined and resulted in errors such as:
Configuring for canyonlands board...
fsl_dma.c:50:2: error: #error "Freescale DMA engine not supported on your
processor"
make[1]: *** No rule to make target `.depend', needed by `libdma.a'. Stop.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
arranged configurations in alphabetical order
CONFIG_CMD_FLASH moved under ifndef CONFIG_SYS_NO_FLASH
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Legacy NAND had been scheduled for removal. Any boards that use this
were already not building in the previous release due to an #error.
The disk on chip code in common/cmd_doc.c relies on legacy NAND,
and it has also been removed. There is newer disk on chip code
in drivers/mtd/nand; someone with access to hardware and sufficient
time and motivation can try to get that working, but for now disk
on chip is not supported.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This is needed for the MPC512x NAND driver (fsl_nfc_nand.c) which already
defines such a 4k plus 218 bytes ECC layout.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch simply converts the board to the hwconfig infrastructure.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
fdt_fixup_esdhc() will either disable or enable eSDHC nodes, and
also will fixup clock-frequency property.
Plus, since DR USB and eSDHC are mutually exclusive, we should
only configure the eSDHC if asked through hwconfig.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds support for eSDHC on MPC837XERDB boards. The WP
switch doesn't seem to work on RDB boards though, the WP pin is
always asserted (can see the pin state when it's in GPIO mode).
FSL DR USB and FSL eSDHC are mutually exclusive because of pins
multiplexing, so user should specify 'esdhc' or 'dr_usb' options
in the hwconfig environment variable to choose between the
devices.
p.s.
Now we're very close to a monitor len limit (196 bytes left using
gcc-4.2.0), so also increase the monitor len by one sector (64 KB).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
This patch implements fdt_fixup_esdhc() function that is used to fixup
the device tree.
The function adds status = "disabled" propery if esdhc pins muxed away,
otherwise it fixups clock-frequency for esdhc nodes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
This patch implements simple hwconfig infrastructure: an
interface for software knobs to control a hardware.
This is very simple implementation, i.e. it is implemented
via `hwconfig' environment variable. Later we could write
some "hwconfig <enable|disable|list>" commands, ncurses
interface for Award BIOS-like interface, and frame-buffer
interface for AMI GUI[1] BIOS-like interface with mouse
support[2].
Current implementation details/limitations:
1. Doesn't support options dependencies and mutual exclusion.
We can implement this by integrating apt-get[3] into the
u-boot. But I didn't bother yet.
2. Since we don't implement hwconfig command, i.e. we're working
with the environement directly, there is no way to tell that
toggling a particular option will need a reboot to take
an effect. So, for now it's advised to always reboot the
target after modifying hwconfig variable.
3. We support hwconfig options with arguments. For example,
set hwconfig dr_usb:mode=peripheral,phy_type=ulpi
That means:
- dr_usb - enable Dual-Role USB controller;
- dr_usb:mode=peripheral - USB in Function mode;
- dr_usb:phy_type=ulpi - USB should work with ULPI PHYs;
The purpose of this simple implementation is to define some
internal API and then we can continue improving user experience
by adding more mature interface, like hwconfig command with
bells and whistles. Or not adding, if we feel that current
interface fits its needs.
[1] http://en.wikipedia.org/wiki/American_Megatrends
[2] Regarding ncurses and GUI with mouse support -- I'm just
kidding.
[3] The comment regarding apt-get is also a joke, meaning that
dependency tracking could be non-trivial. For example, for
enabling HW feature X we may need to disable Y, and turn Z
into reduced mode (like RMII-only interface for ethernet,
no MII).
It's quite trivial to implement simple cases though.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Saving the environment leads to overwriting u-boot itself,
bricking boards. Increase u-boot's image size so the environment
base address doesn't end up overlapping u-boot text.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
When enabling NAND support for a board, one must also define
CONFIG_SYS_64BIT_VSPRINTF because this is needed in nand_util.c
for correct output.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Dave Liu <daveliu@freescale.com>
Cc: Ron Madrid <ron_madrid@sbcglobal.net>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
