Configure debug UART pins as function: "qup9" rather than being regular
gpios. It fixes a hang seen during pinmux setting.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Rather than using magic numbers as clock ids for peripherals import
qcom,gcc-sdm845.h from Linux to be used standard macros for clock ids.
So start using corresponding clk-id macro for debug UART.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
According to u-boot DT recomendation, u-boot specific DT properties belong
to *-uboot.dtsi. Also for starqltechn board (which is the only current
consumer of sdm845.dtsi), the properties are already included in
starqltechn-uboot.dtsi, so remove corresponding redundant properties.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Currently there is a mismatch among DT node overrides in starqltechn
board DTS file and the actual DT nodes in the sdm845.dtsi. So fix that
to align with DT nodes in sdm845.dtsi.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
CONFIG_PREBOOT just cause putting "preboot=CONFIG_PREBOOT" into env list.
Value CONFIG_PREBOOT="run preboot" in defconfig is just nonsense and does
not do anything useful (it is infinite recursion). Config file for this
board already contains default preboot= env variable with correct value,
which has higher priority than CONFIG_PREBOOT and this is reason why
nonsense CONFIG_PREBOOT is ignored.
Remove nonsense and unused CONFIG_PREBOOT from nokia_rx51_defconfig file.
Signed-off-by: Pali Rohár <pali@kernel.org>
We have different dtbs for the Lite and Extended WiFi variants of the
SanCloud BBE.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SanCloud BBE Lite has a Micron Authenta flash device connected to
the spi0 bus.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On AM62x devices, main ESM error event outputs can be routed to
MCU ESM as inputs. So, two ESM device nodes are expected in the
device tree : one for main ESM and another one for MCU ESM.
MCU ESM error output can trigger the reset logic to reset
the device when CTRLMMR_MCU_RST_CTRL:MCU_ESM_ERROR_RESET_EN_Z is
set to '0'.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Apple's M2 SoC very similar to the M1 and can use the same memory map.
The keyboard/trackpad on the MacBook Pro (13-inch, M2, 2022) uses
"dockchannel" as transport instead of SPI and needs a new driver.
USB, NVMe, uart, framebuffer and watchdog are working with the existing
drivers.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
"apple,t8112-dart" uses an incompatible register interface but still
offers the same functionality. This DART is found on the M2 and M1
Pro/Max/Ultra SoCs.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
In preparation of re-sync of mtd stack, we opt to move the current stack
slowly in order to have a more easy sync and test. We would like to
prepare uboot to support no-jedec and no-onfi compliant nand so we need
to clean up a bit the code we have now and upstream some of the support.
In this series we expect no functional change
Tested on:
- imx6ull Micron MT29F2G08ABAGAH4
- imx8mn Macronix MX30LF4G18AC
Upstream linux commit f7025a43a9da26.
The MTD subsystem has its own small museum of ancient NANDs in a form of
the CONFIG_MTD_NAND_MUSEUM_IDS configuration option. The museum contains
stone age NANDs with 256 bytes pages, as well as iron age NANDs with 512
bytes per page and up to 8MiB page size.
It is with great sorrow that I inform you that the museum is being
decommissioned. The MTD subsystem is out of budget for Kconfig options and
already has too many of them, and there is a general kernel trend to
simplify the configuration menu.
We remove the stone age exhibits along with closing the museum
REMARK Don't apply this part from upstream:
Some of the iron age ones are transferred to the regular NAND depot.
Namely, only those which have unique device IDs are transferred, and the
ones which have conflicting device IDs are removed.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit fb3bff5b407e58.
This patch enables support to read the ECC strength and size from the
NAND flash using Toshiba Memory SLC NAND extended-ID. This patch is
based on the information of the 6th ID byte of the Toshiba Memory SLC
NAND.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 3b5206f4be9b65.
Move Macronix specific initialization logic into nand_macronix.c. This
is part of the "separate vendor specific code from core" cleanup
process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 229204da53b31d.
Move AMD/Spansion specific initialization/detection logic into
nand_amd.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 10d4e75c36f6c1.
Move Micron specific initialization logic into nand_micron.c. This is
part of the "separate vendor specific code from core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 9b2d61f80b060c.
Move Toshiba specific initialization and detection logic into
nand_toshiba.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 01389b6bd2f4f7.
Move Hynix specific initialization and detection logic into
nand_hynix.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit c51d0ac59f2420.
Move Samsung specific initialization and detection logic into
nand_samsung.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
In preparation of moving specific nand support that are not jedec
or onfi
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
nand_get_flash_type was reworked in commit 1ca6f9483e. This change
break the Mediatek MT721. Fix it adjust the function call parameters
+include/linux/mtd/rawnand.h:32:62: note: expected 'struct nand_chip *' but argument is of type 'struct mtd_info *'
+ 32 | struct nand_flash_dev *nand_get_flash_type(struct nand_chip *chip,
+ | ~~~~~~~~~~~~~~~~~~^~~~
+drivers/mtd/nand/raw/mt7621_nand.c:1189:48: error: passing argument 2 of 'nand_get_flash_type' from incompatible pointer type [-Werror=incompatible-pointer-types]
+ | ^~~~
+ | |
+ | struct nand_chip *
+include/linux/mtd/rawnand.h:33:49: note: expected 'int *' but argument is of type 'struct nand_chip *'
+ 33 | int *maf_id, int *dev_id,
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
chip points to mtd. Passing chip is enough to have a reference
to mtd when is necessary
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit abbe26d144ec22.
A lot of NANDs are implementing generic features in a non-generic way,
or are providing advanced auto-detection logic where the NAND ID bytes
meaning changes with the NAND generation.
Providing this vendor specific initialization step will allow us to get
rid of full-id entries in the nand_ids table or all the vendor specific
cases added over the time in the generic NAND ID decoding logic.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 7f501f0a72036d.
Store the NAND ID in struct nand_chip to avoid passing id_data and id_len
as function parameters.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 29a198a1592d83.
Auto-detection functions are passed a busw parameter to retrieve the actual
NAND bus width and eventually set the correct value in chip->options.
Rework the nand_get_flash_type() function to get rid of this extra
parameter and let detection code directly set the NAND_BUSWIDTH_16 flag in
chip->options if needed.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
CONFIG_ETHPRIME can be set to DT node name or alias which refers to DT
node. Define ethernet aliases and set ETHPRIME to eth2 which refers to WAN
ethernet port. This removes hardcoded DT node name from U-Boot
configuration file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Change detection of platform/cpu from runtime to compile time via config
define. This completely eliminates compiling code which is not going to run
on selected platform. Code which parses and prints device / revision id
still reads device id from MVEBU_REG_PCIE_DEVID register, but only once.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
uDPU like eDPU does not expose SCSI based peripherals like SATA nor PCI
and for sure it does not have the Intel E1000 PCI card.
So, like for eDPU remove those from the defconfig.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
eDPU does not use SCSI nor it has SATA exposed, and commit
arm: mvebu: a3720: Set BOOT_TARGET_DEVICES list to enabled peripherals
now allows compiling U-boot wihout all of the BOOT_TARGET_DEVICES since
not all boards have all of the listed peripherals exposed.
So, disable SCSI support in defconfig for eDPU.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix MAINTAINERS files for Turris devices, add missing files and add Pali
as maintainer.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
SPL on mvebu loads proper U-Boot from custom Marvell kwbimage format and
therefore support for other binary formats is not required to be present in
SPL. Boot source of proper U-Boot is defined by compile time options and
therefore it is not required to enable all possible and unused peripherals
in SPL by default.
This change decrease size of SPL binaries.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This allows to compile U-Boot without some boot option for some A3720 board
which does not have that peripheral.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
I am currently maintaing the Methode uDPU and eDPU boards so add myself
as the maintainer for them.
Remove the old entry from board/Marvell/mvebu_armada-37xx/MAINTAINERS.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Methode eDPU is an Armada 3720 power board based on the Methode uDPU.
They feature the same CPU, RAM, and storage as well as the form factor.
However, eDPU only has one SFP slot plus a copper G.hn port which does not
work under U-boot.
In order to reduce duplication, split the uDPU DTS into a common one.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
A common external watchdog circuit is kept alive by triggering a short
pulse on the reset pin. This patch adds support for this use case, while
making the algorithm configurable in the devicetree.
The "linux,wdt-gpio" driver being modified is based off the equivalent
driver in the Linux kernel, which provides support for this algorithm.
This patch brings parity to this driver, and is kept aligned with
the functionality and devicetree configuration in the kernel.
It should be noted that this adds a required property named 'hw_algo'
to the devicetree binding, following suit with the kernel. I'm happy to
make this backward-compatible if preferred.
Signed-off-by: Paul Doelle <paaull.git@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for hardware watchdog timer for Amlogic SoCs.
This driver has been heavily inspired by his Linux equivalent
(meson_gxbb_wdt.c).
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philippe Boos <pboos@baylibre.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch enables the recently added watchdog support on the MIPS
Octeon EBB7304 eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds support for the Marvell Octeon watchdog driver, which
currently only support the ARM64 Octeon TX & TX2 platforms. Since the
IP is pretty similar, it makes sense to extend this driver to also
support the MIPS Octeon SoC.
A follow-up patch will enable this watchdog support on the EBB7304
eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
board_get_usable_ram_top() conflated the RAM size with the top address
of RAM. On systems where RAM starts at address 0 these numbers are the
same so it went unnoticed. Update board_get_usable_ram_top() to take
CONFIG_SYS_SDRAM_BASE into account when determining the top address.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
