The fmc base address is defined twice, once in fmc.h and once in stm32.h.
Fix wrong definition in stm32.h.
Remove the definiton in fmc.h.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas Manocha <vikas.manocha@st.com>
Cleanup stm32f7 files:
- use BIT macro
- use GENMASK macro
- use rcc struct instead of macro additions
Add missing stm32f7 register in rcc struct
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA<vikas.manocha@st.com>
This patch adds the DTS source files needed for stm32f746-disco board
The files are based on the stm32f429/469 files from current linux
kernel.
Source for "arch/arm/dts/armv7-m.dtsi": Linux: "arch/arm/boot/dts/armv7-m.dtsi"
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
This patch adds pin control definitions for use in device tree files
The definitions are based on the stm32f746 files from current
linux kernel "include/dt-bindings/pinctrl/stm32f746-pinfunc.h".
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
The check for OMAP3630/3730 only checks for 800MHz 3630/3730, but
anything else is lumped into 36XX/37XX with an assumed 1GHz speed.
Based on the DM3730 TRM bit 9 shows the MPU Frequency (800MHz/1GHZ).
This also adds the ability to distinguish between the DM3730, DM3725,
AM3715, and AM3703 and correctly display their maximum speed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
This reverts commit 8c36e99f21.
There is misunderstanding in commit 8c36e99f21 ("armv8: release
slave cores from CPU_RELEASE_ADDR"). How to bring the slave cores
into U-Boot proper is platform-specific. So, it should be cared
in SoC/board files instead of common/spl/spl.c. As you see SPL
is the acronym of Secondary Program Loader, there is generally
something that runs before SPL (the First one is usually Boot ROM).
How to wake up slave cores from the Boot ROM is really SoC specific.
So, the intention for the spin table support is to bring the slave
cores into U-Boot proper in an SoC specific manner. (this must be
done after relocation. see below.)
If you bring the slaves into SPL, it is SoC own code responsibility
to transfer them to U-Boot proper. The Spin Table defines the
interface between a boot-loader and Linux kernel. It is unrelated
to the interface between SPL and U-Boot proper.
One more thing is missing in the commit; spl_image->entry_point
points to the entry address of U-Boot *before* relocation. U-Boot
relocates itself between board_init_f() and board_init_r(). This
means the master CPU sees the different copy of the spin code than
the slave CPUs enter. The spin_table_update_dt() protects the code
*after* relocation. As a result, the slave CPUs spin in unprotected
code, which leads to unstable behavior.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This feature seems to be sometimes misunderstood. The intention is:
[1] Bring the slaves into the U-Boot proper image, not SPL (unless
you have a special reason to do otherwise).
[2] The operation must be done in a board (SoC) specific manner
since how to wake the slaves from the Boot ROM is SoC specific.
[3] The slaves must enter U-Boot proper after U-Boot relocates
itself because the "cpu-release-addr" property points to the
relocated memory area.
[2] is already explained in the help. We can make [1] even clearer
by mentioning "U-Boot proper" instead of "U-Boot". [3] is missing,
so I am adding it to the list. Instead, "before the master CPU
jumps to the kernel" is a matter of course, so removed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
chiliBoard is a development board which uses chiliSOM as its base.
Hardware specification:
* chiliSOM (TI AM335x, DRAM, NAND)
* Ethernet PHY (id 0)
* USB host (usb1)
* MicroSD slot (mmc0)
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
chiliSOM is a System On Module (http://http://grinn-global.com/chilisom/).
It can't exists on its own, but will be used as part of other boards.
Hardware specification:
* TI AM335x processor
* 128M, 256M or 512M DDR3 memory
* up to 256M NAND
We place source inside arch/arm/mach-omap2/ directory and make it
possible to reuse initialization code (i.e. DDR, NAND init) for all
boards that use it.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a new defconfig file for the AM335x High Security EVM. This config
is specific for the case of memory device booting. Memory device booting
is handled separatly from peripheral booting on HS devices as the load
address changes.
This defconfig is the same as for the non-secure part, except for:
CONFIG_TI_SECURE_DEVICE option set to 'y'
CONFIG_ISW_ENTRY_ADDR updated for secure images.
CONFIG_FIT_IMAGE_POST_PROCESS option set to 'y'
CONFIG_SPL_FIT_IMAGE_POST_PROCESS option set to 'y'
CONFIG_USE_TINY_PRINTF option set to 'y' to reduce SPL size
CONFIG_SPL_SYS_MALLOC_SIMPLE set to 'y' to reduce SPL size
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
spl_init on some boards is called after stack and heap relocation, on
some platforms spl_relocate_stack_gd is called to handle setting the
limit to its value CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN when simple
SPL malloc is enabled during relocation. spl_init should then not
re-assign the old pre-relocation limit when this is defined.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add configuration file with parameters that are very likely to be shared by
all ast2500-based boards.
Add ast2500-board.c file with the init code that is very likely to be
shared by all ast2500-based boards.
Reviewed-by: Simon Glass <sjg@chromium.org>
Clock Driver
This driver is ast2500-specific and is not compatible with earlier
versions of this chip. The differences are not that big, but they are
in somewhat random places, so making it compatible with ast2400 is not
worth the effort at the moment.
SDRAM MC driver
The driver is very ast2500-specific and is completely incompatible
with previous versions of the chip.
The memory controller is very poorly documented by Aspeed in the
datasheet, with any mention of the whole range of registers missing. The
initialization procedure has been basically taken from Aspeed SDK, where
it is implemented in assembly. Here it is rewritten in C, with very limited
understanding of what exactly it is doing.
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for Watchdog Timer, which is compatible with AST2400 and
AST2500 watchdogs. There is no uclass for Watchdog yet, so the driver
does not follow the driver model. It also uses fixed clock, so no clock
driver is needed.
Add support for timer for Aspeed ast2400/ast2500 devices.
The driver actually controls several devices, but because all devices
share the same Control Register, it is somewhat difficult to completely
decouple them. Since only one timer is needed at the moment, this should
be OK. The timer uses fixed clock, so does not rely on a clock driver.
Add sysreset driver, which uses watchdog timer to do resets and particular
watchdog device to use is hardcoded (0)
Reviewed-by: Simon Glass <sjg@chromium.org>
In the cases of some boards, a MACH_TYPE number is used which is either
not registered upstream or worse (for functionality) is re-using the
number of a different (or reference) platform instead. Make sure we
have a comment in these cases.
Cc: Albert ARIBAUD <albert.aribaud@3adev.fr>
Cc: Walter Schweizer <swwa@users.sourceforge.net>
Cc: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
This board is using MACH_TYPE values that were clearly picked during
development and not registered. Remove rather than support.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
With the latest mach-types values we have many instances where we no
longer need to define a value and a few cases where the name (but not
value) have changed slightly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This reverts commit 70b26cd057.
This is not a strict revert as it is easier to fix
board/atmark-techno/armadillo-800eva/armadillo-800eva.c to now the
correct name (same value) than to revert that change too.
Signed-off-by: Tom Rini <trini@konsulko.com>
We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly
update all of the config files we must also update CMD_PART and CMD_GPT to also
be in Kconfig in order to avoid complex logic elsewhere to update all of the
config files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Allow to use define CONFIG_IS_ENABLED
in include/config_fallbacks.h
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
The LS1046A processor has three integrated USB 3.0 controllers
(USB1, USB2, and USB3) that allow direct connection to the USB
ports with appropriate protection circuitry and power supplies.
USB1 and USB2 ports are powered by a NX5P2190UK device, which
supplies 5v power at up to 1.2 A. The power enable and
power-fault-detect pins are connected to the LS1046A processor
via CPLD for individual port management.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS1046AQDS processor has three integrated USB 3.0 controllers
(USB1, USB2, and USB3) that allow direct connection to the USB
ports with appropriate protection circuitry and power supplies.
USB1 and USB2 ports are powered by a NX5P2190UK device, which
supplies 5v power at up to 1.2 A. The power enable and
power-fault-detect pins are connected to the LS1046A processor
via CPLD for individual port management.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Moving arch/arm/mach-litesom/ to arch/arm/cpu/armv7/mx6/ was requested
in [1] during discussion of chiliSOM support patches.
[1] http://lists.denx.de/pipermail/u-boot/2017-January/279137.html
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Remove the trailing semicolon and space.
It's not necessary to have it on the last condition.
Suggested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
According to doc/README.distro:
"fdt_addr_r:
Mandatory. The location in RAM where the DTB will be loaded or copied to when
processing the fdtdir/devicetreedir or fdt/devicetree options in
extlinux.conf."
So add the fdt_addr_r environment variable.
Suggested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Before commit 81c4eccb55 ("imx: mx6: fix USB bmode to use
reserved value") a non-reserved value has been used to trigger
Serial Downloader using bmode, which translated to a GPR9 value
of 0x10. However, on some boards the non-reserved value lead to
unreliable bmode command. With the above mentioned commit, U-boot
switched to use [7:4] b0001, which translates to GPR9 0x10 for
Serial Downloader mode. Check for the new value and classify it
as Serial Downloader mode.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Fabio Estevam <Fabio.Estevam@freescale.com>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
USB Host scanning has been broken since v2016.05.
This is due to all the USB changes that happened between v2016.03
and v2016.05, especially:
2ef117fe4f usb: Remove 200 ms delay in usb_hub_port_connect_change()
a22a264ec3 usb: Change power-on / scanning timeout handling
So we need to increase the init delay to 2s using the usb_pgood_delay
environment variable.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Commit 6e1f4d2652 ("arm: imx-common: add SECURE_BOOT option to
Kconfig") moved the CONFIG_SECURE_BOOT option to Kconfig, so update
the mxc_hab README file to reflect that.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Gary Bisson <gary.bisson@boundarydevices.com>
On mx6qsabreauto the parallel NOR width is 16 bits, so pass configure
CONFIG_SYS_FLASH_CFI_WIDTH correctly so that the CFI driver does not
use 8 bits by default.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
We can use the same header length calculations for both imximage v1 and
v2. This addresses TODO comments about imximage v1 in the current code.
With this patch applied, *header_size_ptr in imximage_set_header() will
have the correct value for both imximage v1 and v2. This is necessary
for people wanting to add proprietary data behind the created imximage.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Cc: sbabic@denx.de
Currently maximum volume size can be specified only if no other
arguments are used. Use '-' placeholder as volume size to allow
maximum volume size to be specified together with volume id and
type.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
