When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
omap-common cache enabling sequence relies on cpu_init_cp15()
(inside start.S) for enabling I-caches. But cpu_init_cp15()
can be skipped if CONFIG_SKIP_LOWLEVEL_INIT is defined. So
enable I-caches if not enabled already.
Debugged-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If CONFIG_SPL_SERIAL_SUPPORT is disabled then the build fails because
serial_init is undefined. Guard preloader_console_init() appropriately
to fix this.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.
This fixes failures such as:
board/ti/am335x/built-in.o: In function `board_late_init':
board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'
which caters for use cases such as:
commit f411b5cca4 ("board: am335x: Always set eth/eth1addr environment
variable")
when Ethernet is required in Linux, but not U-Boot.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
This inhibits the re-inititialization of DDR during an RTC-only resume. If
this is not done, an L3 NOC error is produced as the DDR gets accessed
before the re-init has time to complete. Tested on AM437x GP EVM.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
[j-keerthy@ti.com Ported to Latest Master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Prevent EMIF control of DDR_RESET line on DDR3 am43xx platforms for
am43xx_evm_rtconly_config. Without this DDR is unstable and can become
corrupted after multiple iterations of RTC+DDR mode.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[j-keerthy@ti.com Ported to latest master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Kernel stores information to the RTC_SCRATCH0 and RTC_SCRATCH1 registers
for wakeup from RTC-only mode with DDR in self-refresh. Parse these
registers during SPL boot and jump to the kernel resume vector if the
device is waking up from RTC-only modewith DDR in Self-refresh.
The RTC scratch register layout used is:
SCRATCH0 : bits00-31 : kernel resume address
SCRATCH1 : bits00-15 : RTC magic value used to detect valid config
SCRATCH1 : bits16-31 : board type information populated by bootloader
During the normal boot path the SCRATCH1 : bits16-31 are updated with
the eeprom read board type data. In the rtc_only boot path the rtc
scratchpad register is read and the board type is determined and
correspondingly ddr dpll parameters are set. This is done so as to avoid
costly i2c read to eeprom.
RTC-only +DRR in self-refresh mode support is currently only enabled for
am43xx_evm_rtconly_config.
This is not to be used with epos evm builds.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[j-keerthy@ti.com Rebased to latest u-boot master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
When enabling CONFIG_FASTBOOT_FLASH in am335x_boneblack_defconfig, next
build errors and warnings occur:
arch/arm/mach-omap2/utils.c: In function ‘omap_set_fastboot_cpu’:
arch/arm/mach-omap2/utils.c:26:16: warning: implicit declaration of
function ‘omap_revision’ [-Wimplicit-function-declaration]
u32 cpu_rev = omap_revision();
^~~~~~~~~~~~~
arch/arm/mach-omap2/utils.c:29:7: error: ‘DRA762_ES1_0’ undeclared
(first use in this function)
Include asm/omap_common.h explicitly to avoid those.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER.
This enables users to block text using CONFIG_IS_ENABLED() instead
of resorting to #if ladders with SPL and non-SPL cases.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
TI_SECURE_DEVICE is used by both OMAP2+ and Keystone2 family devices,
and so when ARCH_OMAP2PLUS was used to gate off the OMAP2+ Kconfig
Keystone2 family devices lost this config option.
Move this option out of mach-omap2 Kconfig to a spot accessible by both
families. We picked arch/arm/Kconfig over the TI specific board/ti/
location as this option is not specific to our boards but rather our
architecture.
Plus at some point this option can be changed to just
SECURE_DEVICE, as having secure parts is not exclusive to TI and
so other vendors can interpret this option as needed by their device
configurations.
Fixes: a93fbf4a78 ("ARM: omap2+: rename config to ARCH_OMAP2PLUS and consolidate Kconfig")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Now that omap_hsmmc has support for hs200 mode, change the clock
frequency to 192MHz. Also change the REFERENCE CLOCK frequency to
192MHz based on which the internal mmc clock divider is calculated.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new API to perform iodelay recalibration without isolate
io to be used in uboot.
The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met. The MMC driver can use the new API to
set the IO delay values depending on the MMC mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Fix build warning in arch/arm/mach-omap2/emif-common.c and
arch/arm/mach-omap2/omap4/emif.c with gcc 7.3.0:
warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With driver model enabled in SPL, sdram_init() requires device tree
and malloc to be initialized.
Therefore call spl_early_init() in early_system_init().
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
When in early SPL we make some secure ROM calls that can effect
DRAM, due to this it is more stable to store the args for these
calls in SRAM, but uninitialized and zero'd globals are placed
in BSS, located in DRAM. Force our args into the data section
which is in SRAM during SPL.
Signed-off-by: Andrew F. Davis <afd@ti.com>
The signing certificate name is always 15 chars long, but need not be
null terminated. One solution is then to use printf precision modifiers
to only print this many chars ("%.15s"), but tiny printf does not support
this, so lets just drop printing the cert name for now.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Fix the size calculation in the verify boot. The header size
should be subtracted from the image size, not be assigned to
the image size.
Fixes: 0830d72bb9 ("arm: am33xx: security: adds auth support for encrypted images")
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
DRA762 comes in two packages:
- ABZ: Pin compatible package with DRA742 with DDR@1333MHz
- ACD: High performance(OPP_PLUS) package with new IPs
Both the above packages uses the same IDCODE hence needs to
differentiate using package information in DIE_ID_2.
Add support for the same. Also update clock, ddr, emif information.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
For data integrity, the EMIF1 supports ECC on the data
written or read from the SDRAM. Add support for enabling
ECC support in EMIF1.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
This is a slight difference in emif_ddr_phy_status register offsets for
DRA7xx EMIF and older versions. And ecc registers are available only
in DRA7xx EMIC. Add support for this difference and ecc registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DPLL DRR doesn't have an M4 divider. But the clock driver is trying
to configure M4 divider as 4(writing into a reserved register).
Fixing it by making M4 divider as -1.
Reported-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This commit updates the configuration files needed to support OF_CONTROL
on the OMAP3 EVM baseboard.
Additionally:
- CONFIG_SYS_THUMB_BUILD is enabled
- CONFIG_SPL_ENV_SUPPORT is enabled
Tested using GCC 7.2.0 [--with-float=hard --with-mode=thumb].
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
This header was renamed to rawnand.h in Linux.
The following is the corresponding commit in Linux.
commit d4092d76a4a4e57b65910899948a83cc8646c5a5
Author: Boris Brezillon <boris.brezillon@free-electrons.com>
Date: Fri Aug 4 17:29:10 2017 +0200
mtd: nand: Rename nand.h into rawnand.h
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The kernel gets the ethernet MAC from the ethaddr variable, the omap boards for
devices with USB based eth adapters just set the usbethaddr which doesn't appear
to get passed to the kernel. The same Raspberry Pi code sets both ethaddr and
usbethaddr so lets do that so linux (tested 4.13 and 4.14) get a static rather
than a random MAC address, while not regressing users of usbethaddr.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Configure thermal configs to remain set by default for dra7xx and am57xx
devices.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For the DM TPS65910 driver I'm working on, querying the MPU voltage
should return a value in uV. This value can then be used by the
regulator's standard function set_value to set the MPU voltage.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This converts the following to Kconfig:
CONFIG_NAND_MXC
CONFIG_NAND_OMAP_GPMC
CONFIG_NAND_OMAP_GPMC_PREFETCH
CONFIG_NAND_OMAP_ELM
CONFIG_SPL_NAND_AM33XX_BCH
CONFIG_SPL_NAND_SIMPLE
CONFIG_SYS_NAND_BUSWIDTH_16BIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues,
add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT]
Signed-off-by: Tom Rini <trini@konsulko.com>
'commit fa24eca1f2 ("omap: Add routine for setting fastboot variables")'
adds initial support and usage of "fastboot getvar" command
for DRA75x and DRA72x devices.
and
'commit 0f9e6aee9d ("arm: dra76: Add support for ES1.0 detection")'
adds initial dra76 device definition
This patch is to extend usage of "fastboot getvar" for DRA76 device.
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Extend support for this
revision in "getvar cpu" command.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
[praneeth@ti.com: rebase to u-boot master]
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When eMMC was formattaed for Linux partition table, "userdata" partition
is missing. In this case, part_get_info_by_name() iterates over all
registered drivers (which are PART_TYPE_EFI, PART_TYPE_DOS and
PART_TYPE_ISO). And when it comes to PART_TYPE_ISO (which has empty
partition table), we can see next warning in U-Boot output:
** First descriptor is NOT a primary desc on 1:1 **
This patch switches to part_get_info_by_name_type() API in order to
check only EFI partitions for "userdata" partitions. This eliminates
mentioned warning.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using regular $partitions variable (for Linux boot), we can see
some unwanted messages:
> ERROR: cannot find partition: 'userdata'
> at arch/arm/mach-omap2/utils.c:96/omap_mmc_get_part_size()
> Warning: fastboot.userdata_size: unable to calc
Let's remove those, as missing 'userdata' partition is correct behavior
for Linux partition, and we don't want to see some Android-related
messages in this case.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
In order to be able to select the right DTB, we need to have identified the
board before spl_early_init() is called.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds support for authentication of both plain
text and encrypted binaries. A new SECDEV package is needed
to enable encryption of binaries by default for AM3x.
The ROM authentication API detects encrypted images at
runtime and automatically decrypts the image if the
signature verification passes.
Addition of encryption on AM3x results in a change in the
image format. On AM4x, AM5x and, on AM3x devices signing
clear test images, the signature is appended to the end of the
binary.
On AM3x, when the SECDEV package is used to create signed
and encrypted images, the signature is added as a header
to the start of the binary. So the binary size calculation
has been updated to reflect this change.
The signing tools and encrypted image format for AM3x
cannot be changed to behave like AM4x and AM5x to
maintain backward compatibility with older Sitara
M-Shield releases.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
With the device tree ported from Linux 4.13, this enables
Driver Model and Device Tree support for the am3517-evm
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
This patch provides default implementations of the two functions
set_uart_mux_conf and set_mux_conf_regs. Hence boards not using
them do not need to provide their distinct empty definitions.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
When the OP-TEE image is built for secure paging the load address may be
in SRAM, remove checks that prevent this.
Signed-off-by: Harinarayan Bhatta <harinarayan@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This converts the following to Kconfig:
CONFIG_EMIF4
CONFIG_SDRC
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The DTS files had some spacing issues and they needed fixing. This
pull re-sync's the OMAP3xx related DTS files with Linux 4.13-RC5.
To keep the DTS and DTSI files clean and in sync with Linux, new
u-boot.dtsi files are added.
Signed-off-by: Adam Ford <aford173@gmail.com>
V3: The resync broke card detect on MMC1 on Logic PD's Torpedo,
so we add the cd-invert to the Torpedo's -u-boot.dtsi file.
V2: Add the u-boot.dtsi files for OMAP3, OMAP36xx, and Torpedo
Remove the need for the second patch in the series
DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Add support for detection
of SR2.1 version of DRA71x family of processors.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76-evm has the ddr parts connectedi running at 666MHz:
EMIF1: MT41K512M16HA-125 AIT:A x 2
EMIF2: MT41K512M8RH-125-AAT:E x 4
Add support for configuring the above DDR parts.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76-evm uses lp8736 and tps65917 pmic for powering on
various peripherals. Add data for these pmics and register
for dra76-evm.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
dra76 family is a high-performance, infotainment application
device, based on OMAP architecture on a 28-nm technology.
This contains most of the subsystems, peripherals that are
available on dra74, dra72 family. This SoC mainly features
Subsystems:
- 2 x Cortex-A15 with max speed of 1.8GHz
- 2 X DSP
- 2 X Cortex-M4 IPU
- ISS
- CAL
- DSS
- VPE
- VIP
Connectivity peripherals:
- 1 USB3.0 and 3 USB2.0 subsystems
- 1 x SATA
- 2 x PCI Express Gen2
- 3-port Gigabit ethernet switch
- 2 x CAN
- MCAN
Adding CPU detection support for the dra76 ES1.0 soc
and update prcm, control module, dplls data.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
