Move U-Boot specific properties into rk3399-evb u-boot
specific dtsi file.
This would help to sync the devicetrees from Linux whenever
required instead of adding specific nodes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move U-Boot specific properties into rk3399-puma u-boot
specific dtsi file.
This would help to sync the devicetrees from Linux whenever
required instead of adding specific nodes.
Cc: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
If the VBUS regulator is always-on, XHCI will fail to detect USB 3.0
devices; USB 2.0 devices will work however.
Make the VBUS regulator controllable and tie it to only the XHCI. This
makes all three USB ports usable.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ROC-RK3328-CC from Firefly and Libre Computer Project is a credit
card size development board based on the Rockchip RK3328 SoC, with:
- 1/2/4 GB DDR4 DRAM
- eMMC connector for optional module
- micro SD card slot
- 1 x USB 3.0 host port
- 2 x USB 2.0 host port
- 1 x USB 2.0 OTG port
- HDMI video output
- TRRS connector with audio and composite video output
- gigabit Ethernet
- consumer IR receiver
- debug UART pins
The ROC-RK3328-CC has the enable pin of the SD card power switch tied
to GPIO_0_D6. This pin also has the function SDMMC0_PWREN, which is
muxed by default. SDMMC0_PWREN is an active high signal controlled by
the MMC controller, however the switch enable is active low, and
pulled low (enabled) by default to make things work on boot.
As such, we need to mux away from SDMMC0_PWREN and use GPIO to enable
power to the card. The default GPIO state for the pin is pull-down and
input, which doesn't require extra configuration when paired with the
external pull-down and active low switch.
Deal with this by enabling regulator support in SPL, and setting
"u-boot,dm-spl" for the regulator and other device nodes needed for
muxing the pin.
The device tree file is synced from the Linux kernel next-20200324.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This syncs rk3328 device tree files from the Linux kernel next-20200324.
The last commit to touch these files is:
b2411befed60 ("arm64: dts: add bus to rockchip amba nodenames")
Additional changes not yet in the Linux kernel include:
arm64: dts: rockchip: rk3328: drop #address-cells, #size-cells from grf node
arm64: dts: rockchip: rk3328: drop non-existent gmac2phy pinmux options
arm64: dts: rockchip: rk3328: Replace RK805 PMIC node name with "pmic"
Changes include:
- conversion of raw pin numbers to macros
- removal of deprecated RK_FUNC_* macros
- update of device tree binding headers
- new devices
- device tree cleanups
- gmac2phy disabled in -u-boot.dtsi as it is not supported in U-boot
This includes a re-ordering of the USB device nodes compared to upstream
Linux, moving the dwc2 OTG controller after the EHCI/OHCI nodes. This is
currently required as otherwise the dwc2 controller would not be able to
detect devices in some cases. This may be due to lack of USB PHY support
in U-boot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The USB PHYs on the RK3328 aren't supported, nor are any other generic
PHYs. Because upstream Linux device trees already include the USB PHYs
and references in the USB hosts, this would result in various calls
to the generic PHY API to fail.
Instead, just disable generic PHY support for now.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This syncs the rk3328 power domain header file from Linux kernel
next-20200324, to support newer hardware blocks when syncing the
device tree files.
The last non-merge commit to touch it was
b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Loic Devulder <ldevulder@suse.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This syncs the rk3328 clock header file from Linux kernel next-20200324,
to support newer hardware blocks when syncing the device tree files.
The last non-merge commit to touch it was
0dc14b013f79 ("clk: rockchip: add clock id for watchdog pclk on rk3328")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Loic Devulder <ldevulder@suse.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The "hnp-srp-disable" property for dwc2 is specific to U-boot, not part
of upstream Linux's device tree bindings.
Move it to rk3328-u-boot.dtsi to avoid losing it when syncing device
tree files.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device tree file for rk3328-evb in the Linux kernel does not have
gmac2io enabled. Instead, gmac2phy is enabled, but that is not supported
in U-boot.
Move the gmac2io related nodes to rk3328-evb-u-boot.dtsi to preserve the
current functionality. When the device tree files are synced, gmac2phy
should be marked as "broken" in -u-boot.dtsi files.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Loic Devulder <ldevulder@suse.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
USB 3.0 is only supported in U-boot, not in the Linux kernel where the
device tree files are ultimately synced from. While the xhci node was
moved, the external vbus regulator was not.
Move it as well.
Fixes: 2e91e2025c ("rockchip: rk3328: migrate u-boot node to -u-boot.dtsi")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Loic Devulder <ldevulder@suse.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
In case of a power interruption, human intervention is required which
is not desirable if the device is installed at a remote location. Drop
yellow LED as it is not much of use. Keep red LED(diy-led) as it is, to
indicate board in full power mode.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a driver for the rng device found on rockchip platforms.
Support rng module of crypto v1 and crypto v2.
Signed-off-by: Lin Jinhan <troy.lin@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add rng node in rk3399-u-boot.dtsi and enable it in
rk3399-evb-u-boot.dtsi.
Signed-off-by: Lin Jinhan <troy.lin@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The file <board name>-u-boot.dtsi inculde automatically by the build
system, no need to add this to dts file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
roc-rk3399-pc has an FE1.1 USB 2.0 HUB which connects two USB ports
(HOST1 and HOST2). For end devices to work we need to enable USB hub
so that HOST detects there presence and enumerates them accordingly.
This requires explicit pinctrl within gpio enablement.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use ofnode_decode_display_timing() instead of
fdtdec_decode_display_timing() to parse display timing, so that we can
support live DT.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rk_edp.c and rk_lvds.c files reference rk_setreg which is declared in
hardware.h so include it so the drivers build. Adjust rk_lvds.c so
includes are in alphabetical order while updating.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
The build currently fails with
drivers/spi/mpc8xxx_spi.c:64:3: warning: implicit declaration of function ‘dev_err’ [-Wimplicit-function-declaration]
...
drivers/spi/built-in.o: In function `mpc8xxx_spi_set_speed':
drivers/spi/mpc8xxx_spi.c:227: undefined reference to `dev_err'
Fixes: 4856cc7a97 (mpc8xxx_spi: implement real ->set_speed)
Fixes: 1a7b462dee (mpc8xxx_spi: put max_cs to use)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The free() function checks if its argument is NULL. It is superfluous to do
the same check on the calling side.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This adds build and flash steps for Actions S700
based Cubieboard7 board.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
The Cubieboard is a single board computer containing a
Actions S700 SoC(with 4 ARMv8 Cortex-A53 cores).
This patch adds respective defconfig alongwith .dts(copied
from Linux v5.5-rc6 with hash "b3a987b0264d").
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch moves some of the config options from bubblegum_96_defconfig
to respective Kconfig files.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch adds basic support for Actions Semi based S700
SoC, which is driven by common owl framework.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Devices like uart and clk are needed to be enabled before relocation.
this patch adds u-boot.dtsi file that mark these device as dm-pre-reloc.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch adds .dtsi file(sync with Linux 5.5-rc6 with hash "b3a987b0264d")
and required binding for S700 SoC that is a 64-bit Quad-core ARM
Cortex-A53 cores.
It also provisions dts file to be built based on selected
platform(CONFIG_MACH_S900/S700).
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch converts S900 clock driver to something common that can
be used for other SoCs, for instance S700(few of clk registers are same).
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Devices like uart and clk are needed to be enabled before relocation.
This patch adds u-boot.dtsi file that mark these device as dm-pre-reloc.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Synchronize device tree bindings with v5.5-rc6 tag with commit id
"b3a987b0264d".
Also, it removes older clock binding defined for S900 along with undocumented
compatible string "actions,s900-serial" from serial driver and adapts clock
driver to cater to new bindings.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch adds "actions,owl-uart" string to the owl uart driver. It
is also defined in Linux kernel.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Now that memory maps(for both S700 and S900 SoCs) can be managed using
a common file, rename sysmap-s900 to sysmap-owl to reflect the same.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This commit adds common arch support for Actions Semi Owl
series SoCs and removes the Bubblegum96 board files.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
The free() function checks if its argument is NULL. We should avoid
checking for NULL before calling free like in
if (result->tds)
free(result->tds);
The list of relevant functions differs between Linux and U-Boot, e.g. we
use free().
Adjust the list of relevant functions.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Casting the (void *) output of memory allocation functions before
assignment like in
sata->cmd_hdr_tbl_offset = (void *)malloc(length + align);
is useless.
Adopt the Linux kernel script
scripts/coccinelle/api/alloc/alloc_cast.cocci.
Now 'make coccicheck' generates warnings like:
./drivers/ata/fsl_sata.c:143:29-33:
WARNING: casting value returned by memory allocation function
to (void *) is useless.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
b42841b7bb62 kbuild: Get rid of KBUILD_STR
2aedcd098a94 kbuild: suppress annoying "... is up to date." message
9c8fa9bc08f6 kbuild: fix if_change and friends to consider argument order
ebf003f0cfb3 kbuild: Consolidate header generation from ASM offset information
2982c953570b kbuild: remove redundant $(wildcard ...) for cmd_files calculation
8a78756eb545 kbuild: create object directories simpler and faster
4d4b5c2e3b6e treewide: remove explicit rules for *offsets.s
01d509a48b46 kbuild: remove unimportant comments from ./Kbuild
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
if_changed must have FORCE as a prerequisite.
Add $(obj)/dts/dt-platdata.o to 'targets' so that the corresponding
.cmd file is included.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Remove the references in README on CONFIG_SYS_RCAR_I2C_* not use
in U-Boot drivers/i2c/rcar_i2c.c, since commit a4d9aafadb ("i2c:
rcar_i2c: Remove the driver") and commit a06a0ac36d ("i2c: rcar_i2c:
Add DM and DT capable I2C driver")
Checked by the command: grep -r SYS_RCAR_I2C *
And these CONFIG are only defined in
arch/arm/mach-rmobile/include/mach/rcar-base.h
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function does not modify the device to change it to use const *, so
that callers with a const udevice * can call it without a cast.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
