The advanced address translation provided by CONFIG_SPL_OF_TRANSLATE is
needed to determine the base address of the uart0 peripheral on am335x
platforms when CONFIG_SPL_OF_CONTROL is enabled.
If CONFIG_SPL_OF_CONTROL is enabled in the base (non-spiboot)
am335x_evm_defconfig, then CONFIG_SPL_OF_TRANSLATE will also need to be
enabled there. Unfortunately this cannot be done pre-emptively due to
the kconfig dependencies.
The TI clk-ctrl & TI sysc drivers are also required to bring up the SPI
bus on am335x platforms.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Pre 2023.01 the bmp_logo was built as part of the tools-only_defconfig
build, something changed and the VIDEO dep needed to build it
is no longer pulled in so fix that by explicitly defining it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add configuration file for mini u-boot configuration which runs on a
smaller footprint from on chip memory(OCM). This configuration has
required CONFIG's enabled to support octal spi flash and uses DCC terminal
for console output. Add required dts for octal spi flash mini u-boot
configuration.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add configuration file for mini u-boot configuration which runs on a
smaller footprint from on chip memory(OCM). This configuration has
required CONFIG's enabled to support qspi flash and uses DCC terminal
for console output. Add required dts files for qspi mini configuration.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add soc_xilinx_versal_net driver to identify the family & revision of
versal-net SoC. Add Kconfig option CONFIG_SOC_XILINX_VERSAL_NET to
enable/disable this driver. To enable this driver by default, add this
config to xilinx_versal_net_virt_defconfig file. This driver will be
probed using platdata U_BOOT_DEVICE structure which is specified in
mach-versal-net/cpu.c.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/613d6bcffd9070f62cf348079ed16c120f8fc56f.1668612993.git.michal.simek@amd.com
Versal NET mini U-Boot configuration is used for memory testing that's why
load address can't be really placed in memory which doesn't need to work
that's why move it to start of OCM which is the same memory which U-Boot is
running from.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Axi qspi controller supports 32-bit & 24-bit addressing modes
for micron, macronix & spansion flash parts. But for winbond
flashes it only supports 24-bit addressing mode.
Enable CONFIG_SPI_FLASH_BAR to use extended addressing mode
to make 32-bit addressing mode work on all flashes.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/f3864966c8ddd766a1702ad61b0e008a1f57462f.1665565423.git.michal.simek@amd.com
This converts the following to Kconfig:
CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NONCACHED_MEMORY
To do this we introduce CONFIG_SYS_HAS_NONCACHED_MEMORY as a bool to
gate if we are going to have noncached_... functions available and then
continue to use CONFIG_SYS_NONCACHED_MEMORY to store the size of said
cache. We make this new option depend on both the architectures which
implement support and the drivers which make use of it.
Cc: Tom Warren <twarren@nvidia.com>
Cc: Mingming lee <mingming.lee@mediatek.com>
Cc: "Ying-Chun Liu (PaulLiu)" <paul.liu@linaro.org>
Cc: Alban Bedel <alban.bedel@avionic-design.de>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_MONITOR_LEN
To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_MMC_MAX_BLK_COUNT
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This converts the following to Kconfig:
CONFIG_SYS_MAX_NAND_DEVICE
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_LOADS_BAUD_CHANGE
CONFIG_LOADS_ECHO
As part of this, we move CMD_SAVES to be after CMD_LOADS as they are
logically related (load or save an s-record format file) and this makes
grouping of CONFIG_SYS_LOADS_BAUD_CHANGE easier.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_INIT_RAM_LOCK
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Switch to use binman to pack images
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
To properly operate the Nano with LPDDR4 at 1.6GHz, the
voltage needs to be adjusted before DDR is initialized.
Enable the PMIC in SPL to do this.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The imx8mn_beacon board does not use the same memory map as the reference
design from NXP or other imx8mn boards. As such, memory is more limited
in SPL.
Moving SPL_BSS_START_ADDR and SPL_STACK to default locations increases
the amount of available meory for the SPL stack. Doing this allows
the board to no longer define CONFIG_MALLOC_F_ADDR.
Since SYS_LOAD_ADDR also does not align with other boards, move it too.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Enable insertion of version variable into U-Boot environment on DHSOM,
to make it possible to check U-Boot version e.g. in U-Boot scripts.
Signed-off-by: Marek Vasut <marex@denx.de>
Add support for the MSC SM2S-IMX8PLUS SMARC Module. Tested in conjunction
with the MSC SM2-MB-EP1 Mini-ITX Carrier Board.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
The downstream U-Boot distributed by Beacon stores the environment
in the eMMC and the end of partition 2. This allow the environment
to stay on the SOM regardless of the boot source.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
In order to boot over USB, the device tree needs to enable
a few extra nodes in SPL. Since the USB driver has the
ability to detect host/device, the dr_mode can be removed
from the device tree since it needs to act as a device when
booting and OTG is the default mode. Add USB boot support
to spl_board_boot_device and enable the corresponding config
options.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
There are a few functions which are not essential for use in
SPL, but they take up enough space to make other preferred
features not fit. Remove the extras.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The RD-AC5X-32G16HVG6HLG-A0 development board main components and
features include:
* Main 12V/54V power supply
* 270 Gbps throughput packet processor on the main board
* DDR4:
* SR1: 2GB DDR4 2400MT/S(1GB x 2 pcs ) with ECC(1GB x 1 pcs)
* SR2: 4GB DDR4 2400MT/S(2GB x 2 pcs ) with ECC(2GB x 1 pcs)
* PCB co-layout with 4GB device to support 8GB (Dual CS) requirement
* 16GB eMMC (Samsung KLMAG1JETD-B041006)
* 16MB SPI NOR(GD25Q127C)
* 32 x 1000 Base-T interfaces
* 16 x 2500 Base-T interfaces
* SR1: 88E2540*4
* SR2: 88E2580*1+88E2540*2
* Six (6) x 25G Base-R SFP28 interfaces
* One (1) x RJ-45 console connector, interfacing to the on board UART
* One (1) x USB Type-A connector, interfacing to the USB 2.0 port (0)
* One (1) x USB Type-mini B connector, interfacing to the USB 2.0 port (1)
* One (1) x RJ-45 1G Base-T Management port, interfacing to the host
port (shared with PCIe) Connected to 88E1512 Gigabit Ethernet Phy
* One (1) x Oculink port, interfacing to the PCIe port for external CPU
connection
* POE 802.3AT support on Port 1 ~ Port 32, 802.3BT support on Port 33 ~
Port 48 (Microsemi PD69208T4, PD69208M or TI TPS2388,TPS23881
solution)
* POE total power budget 780W
* LED interfaces per network port/POE
* LED interfaces (common) showing system status
* PTP TC mode Supported (Reserved M.2 connector to support BC mode)
Signed-off-by: Chris Packham <judge.packham@gmail.com>
The struct is only used to overlay the MMIO region, so the behavior is
the same. This obsoletes the Kconfig option for the number of ports.
Signed-off-by: Samuel Holland <samuel@sholland.org>
This patch updates Microchip MPFS Icicle Kit support. For now,
add Microchip QSPI driver and a small 4MB reservation is
made at the end of 32-bit DDR to provide some memory for
the HSS to use.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This converts the following to Kconfig:
CONFIG_SYS_MIPS_TIMER_REQ
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
