Commit graph

22 commits

Author SHA1 Message Date
Tom Rini
cbabe7f87f configs: Migrate and re-enabled CONFIG_CMD_MTDPARTS
Now that CMD_UBI does not select CMD_MTDPARTS we need to make platforms
that had been enabling it turn it on by hand.  This exposed that we had
not yet migrated CMD_MTDPARTS fully, so do so now.

Fixes: 86dfa556d9 ("cmd: ubi: Remove useless call to mtdparts_init()")
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-11-14 10:53:27 -05:00
Adam Ford
2fe88d4522 Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig
This converts the following to Kconfig:
   CONFIG_FLASH_CFI_DRIVER
   CONFIG_SYS_FLASH_USE_BUFFER_WRITE
   CONFIG_FLASH_CFI_MTD
   CONFIG_SYS_FLASH_PROTECTION
   CONFIG_SYS_FLASH_CFI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-19 19:19:50 -04:00
Masahiro Yamada
b07f6e9faf ARM: uniphier: enable CONFIG_CMD_UBI
Now that CONFIG_SYS_MONITOR_LEN increased, we have room for enabling
more options again.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-11 20:37:17 +09:00
Tom Rini
8c5cad05c9 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-03 15:26:12 -04:00
Tom Rini
86cf1c8285 configs: Migrate CONFIG_NR_DRAM_BANKS
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16 16:45:02 -04:00
Tom Rini
e966471562 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-07 21:40:14 -04:00
Masahiro Yamada
ae7a0d5b66 ARM: uniphier: enable MTD partition and UBI
Enable "mtdparts" and "ubi" commands for uniphier_v8_defconfig to
use UBI on NAND devices.

Enable only "mtdparts" for uniphier_{v7,ld4_sld8}_defconfig because
enabling UBI would increase 170KB, which would be memory footprint
problem.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-07-25 08:47:53 +09:00
Adam Ford
9c5b00973b Convert CONFIG_MTD_PARTITIONS et al to Kconfig
This converts the following to Kconfig:
   CONFIG_MTD_PARTITIONS
   CONFIG_MTD_DEVICE

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-22 19:20:17 -04:00
Masahiro Yamada
b0e8bb4d01 ARM: uniphier: enable CONFIG_SNI_AVE and disable CONFIG_SMC911X
Enable the on-chip ethernet driver for uniphier_{v7,v8}_defconfig.
Disable the on-board SMC911x because it has not migrated to the
driver model yet - it is not possible to enable DM and non-DM
drivers at the same time.

The CONFIG_SMC911X for uniphier_ld4_sld8_defconfig is still kept
because the on-chip ethernet driver for LD4, sLD8 is not supported
yet.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-06-23 01:28:08 +09:00
Tom Rini
358b6a20e4 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-04 11:57:37 -04:00
Tom Rini
c9542eae0b configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-07 20:37:13 -04:00
Adam Ford
d021e94210 Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig
This converts the following to Kconfig:
   CONFIG_BOOTP_BOOTPATH
   CONFIG_BOOTP_DNS
   CONFIG_BOOTP_GATEWAY
   CONFIG_BOOTP_HOSTNAME
   CONFIG_BOOTP_PXE
   CONFIG_BOOTP_SUBNETMASK
   CONFIG_CMDLINE_EDITING
   CONFIG_AUTO_COMPLETE
   CONFIG_SYS_LONGHELP
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-23 21:41:49 -05:00
Tuomas Tynkkynen
a4fa811463 cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA
cmd/Makefile has:

ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif

which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant

 # CONFIG_CMD_FPGA is not set

can be removed from board defconfigs that don't actually have an FPGA.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-05 20:58:11 -05:00
Masahiro Yamada
7e3caa81e0 Move CONFIG_PANIC_HANG to Kconfig
Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26 13:10:24 -05:00
Tom Rini
7af2e3648f configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-12-18 20:19:09 -05:00
Masahiro Yamada
53c149c3a5 ARM: uniphier: set CONFIG_LOGLEVEL to 6
Print out KERN_NOTICE or higher level log messages.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:59 +09:00
Masahiro Yamada
0b55abd34a ARM: uniphier: enable DWC3 xHCI driver really
I thought commit d37d31849c ("ARM: uniphier: enable DWC3 xHCI
driver") enabled CONFIG_USB_DWC3_UNIPHIER, but CONFIG_USB_XHCI_DWC3
was missing in uniphier_v7_defconfig.  Re-add.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-23 01:02:05 +09:00
Adam Ford
8daec2d9d3 net: Add SMC911X driver to Kconfig, convert
We add the various SMC91XX symbols to drivers/net/Kconfig and then this
converts the following to Kconfig:
   CONFIG_SMC911X
   CONFIG_SMC911X_BASE
   CONFIG_SMC911X_16_BIT
   CONFIG_SMC911X_32_BIT

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Apply to the rest of the tree, re-squash old and new patch]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-20 21:40:26 -04:00
Tom Rini
308e066566 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-16 21:35:43 -04:00
Masahiro Yamada
d37d31849c ARM: uniphier: enable DWC3 xHCI driver
Enable CONFIGs for the DWC3 core and the UniPhier specific glue layer.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-15 22:32:25 +09:00
Tuomas Tynkkynen
ad12dc1844 cmd: Toggle the default value of CONFIG_CMD_IMLS
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
   i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-10 17:51:04 -04:00
Masahiro Yamada
81b9bb5fcb ARM: uniphier: merge two defconfig files into uniphier_v7_defconfig
The main difference between Pro4 and PXs2/LD6b is the Denali NAND
IP version.  This is now distinguished by DT.  Merge the two defconfig
files into uniphier_v7_defconfig.

Update the README.uniphier too.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-09-18 20:26:06 +09:00
Renamed from configs/uniphier_pxs2_ld6b_defconfig (Browse further)