Schema file in YAML must be provided in board/ti/common for validating
input config files and packaging system firmware. The schema includes
entries for rm-cfg, board-cfg, pm-cfg and sec-cfg.
Board config files must be provided in board/ti/<devicename> in YAML.
These can then be consumed for generation of binaries to package system
firmware. Added YAML configs for J721E in particular.
Signed-off-by: Tarun Sahu <t-sahu@ti.com>
[n-francis@ti.com: prepared patch for upstreaming]
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
This matches how it was done for pre-K3 TI platforms and it allows
us to move the forward declaration out of sys_proto.h.
It also removes the need for K3_BOARD_DETECT as one is free to simply
override the weak function in their board files as needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
For non TI boards it is not possible to enable the do_board_detect()
call as TI_I2C_BOARD_DETECT is defined in board/ti/common/Kconfig.
I want to use do_board_detect() to dectect boards and properties based
on some SPI communication with a FPGA.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
EEPROM detection logic in ti_i2c_eeprom_get() involves figuring out
whether addressing is 1-byte or 2-byte. There are currently different
behaviours seen across boards as documented in commit bf6376642f
("board: ti: common: board_detect: Fix EEPROM read quirk"). Adding to
the list, we see that there are 2-byte EEPROMs that read properly
with 1-byte addressing with no offset.
For ti_i2c_eeprom_am6_get where eeprom parse operation is dynamic, the
earlier commit d2ab2a2baf ("board: ti: common: board_detect: Fix
EEPROM read quirk for AM6 style data") tried to resolve this by running
ti_i2c_eeprom_get() twice. However this commit along with its former
commit fails on J7 platforms where EEPROM successfully return back the
header on 1-byte addressing and continues to do so until an offset is
introduced. So the second read incorrectly determines the EEPROM as
1-byte addressing.
A more generic solution is introduced here to solve
this issue: 1-byte read without offset and 1-byte read with offset. If
both passes, it follows 1-byte addressing else we proceed with 2-byte
addressing check.
Tested on J721E, J7200, DRA7xx, AM64x
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Fixes: d2ab2a2baf (board: ti: common: board_detect: Fix EEPROM read quirk for AM6 style data)
Fixes: bf6376642f (board: ti: common: board_detect: Fix EEPROM read quirk)
Tested-By: Matwey V. Kornilov <matwey.kornilov@gmail.com>
The situation is similar to commit bf6376642f ("board: ti: common:
board_detect: Fix EEPROM read quirk"). This is seen on a variant of
eeproms seen on some BeagleBone-AI64 which now has a mix of both 1 byte
addressing and 2 byte addressing eeproms.
Unlike the am335x (ti_i2c_eeprom_am_get) and dra7
(ti_i2c_eeprom_dra7_get) which use constant data structure which allows
us to do a complete read of the data, the
am6(ti_i2c_eeprom_am6_get) eeprom parse operation is dynamic.
This removes the option of being able to read the complete eeprom data
in one single shot.
Fortunately, on the I2C bus, we do see the following behavior: In 1
byte mode, if we attempt to read the first header data yet again, the
misbehaving 2 byte addressing device acts in constant addressing mode
which results in the header not matching up and follow on attempt at 2
byte addressing scheme grabs the correct data.
This costs us an extra ~3 milliseconds, which is a minor penalty
compared to the consistent image support we need to have.
Reported-by: Jason Kridner <jkridner@beagleboard.org>
Fixes: a58147c2db ("board: ti: common: board_detect: Do 1byte address checks first.")
Signed-off-by: Nishanth Menon <nm@ti.com>
There are three different kinds of EEPROM possibly present on boards.
1. 1byte address. For those we should avoid 2byte address in order
not to rewrite the data. Second byte of the address can potentially
be interpreted as the data to write.
2. 2byte address with defined behaviour. When we try to use 1byte
address they just return "FF FF FF FF ... FF"
3. 2byte address with undefined behaviour (for instance, 24LC32AI).
When we try to use 1byte address, then their internal read
pointer is changed to some value. Subsequential reads may be
broken.
To gracefully handle both case #1 and case #3 we read all required
data from EEPROM at once (about 80 bytes). So either all the data is
valid or we fallback to 2byte address.
Cc: Nishanth Menon <nm@ti.com>
Fixes: a58147c2db ("board: ti: common: board_detect: Do 1byte address checks first.")
Reference: https://lore.kernel.org/all/CAJs94Ebdd4foOjhGFu9Bop0v=B1US9neDLxfhgcY23ukgLzFOQ@mail.gmail.com/
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Acked-by: Nishanth Menon <nm@ti.com>
Do 1 byte address checks first prior to doing 2 byte address checks.
When performing 2 byte addressing on 1 byte addressing eeprom, the
second byte is taken in as a write operation and ends up erasing the
eeprom region we want to preserve.
While we could have theoretically handled this by ensuring the write
protect of the eeproms are properly managed, this is not true in case
where board are updated with 1 byte eeproms to handle supply status.
Flipping the checks by checking for 1 byte addressing prior to 2 byte
addressing check prevents this problem at the minor cost of additional
overhead for boards with 2 byte addressing eeproms.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Due to supply chain issues, we are starting to see a mixture of eeprom
usage including the smaller 7-bit addressing eeproms such as 24c04
used for eeproms.
These eeproms don't respond well to 2 byte addressing and fail the
read operation. We do have a check to ensure that we are reading the
alternate addressing size, however the valid failure prevents us
from checking at 1 byte anymore.
Rectify the same by falling through and depend on header data comparison
to ensure that we have valid data.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The eeprom data area is much bigger than the data we intend to store,
however, with bad programming, we might end up reading bad records over
and over till we run out of eeprom space. instead just exit when 10
consecutive records are read.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The BeagleBone platforms all use a common mechanism to discover and
identify extension boards (called "capes"): each extension board has an
I2C-connected EEPROM describing itself.
This patch implements a generic extension_scan_board() feature that can
be used by all BeagleBone platforms to read those I2C EEPROMs and fill
in the list of "extension" structures.
Following commits will enable this common logic on two BeagleBone
platforms.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There shouldn't be a need to call additional i2c read if above failed
already. Based on comment it should be enough to try to detect legacy
boards which are mentioned in the comment.
Fixes: 2463f6728e ("ti: common: board_detect: Allow DM I2C without CONFIG_DM_I2C_COMPAT")
Fixes: 0bea813d00 ("ARM: omap-common: Add standard access for board description EEPROM")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current usage of eeprom apis produce a build failure when
CONFIG_TI_I2C_BOARD_DETECT is not defined. Add stub function for these
apis to avoid build failures.
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
When building this code with clang-10 a number of warnings will be
generated along the lines of:
warning: address of array 'ep->version' will always evaluate to 'true'
Convert these checks to checking the strlen of the part of the array we
care about. As this array will be null terminated previously by us,
this is safe.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
The TI J721E EVM system on module (SOM), the common processor board, and
the associated daughtercards have on-board I2C-based EEPROMs containing
board config data. Use the board detection infrastructure to do the
following:
1) Parse the J721E SOM EEPROM and populate items like board name, board
HW and SW revision as well as board serial number into the TI common
EEPROM data structure residing in SRAM scratch space
2) Check for presence of daughter card(s) by probing associated I2C
addresses used for on-board EEPROMs containing daughter card-specific
data. If such a card is found, parse the EEPROM data such as for
additional Ethernet MAC addresses and populate those into U-Boot
accordingly
3) Dynamically apply daughter card DTB overlays to the U-Boot (proper)
DTB during SPL execution
4) Dynamically create an U-Boot ENV variable called name_overlays
during U-Boot execution containing a list of daugherboard-specific
DTB overlays based on daughercards found to be used during Kernel
boot.
This patch adds support for the J721E system on module boards containing
the actual SoC ("J721EX-PM2-SOM", accessed via CONFIG_EEPROM_CHIP_ADDRESS),
the common processor board ("J7X-BASE-CPB"), the Quad-Port Ethernet
Expansion Board ("J7X-VSC8514-ETH"), the infotainment board
("J7X-INFOTAN-EXP") as well as for the gateway/Ethernet switch/industrial
expansion board ("J7X-GESI-EXP").
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Use dm_i2c_probe() rather than i2c_get_chip() when trying to access
board-detection EEPROM devices. This has the advantage of more gracefully
handling the case when the EEPROM is not present by allowing to exit the
function early rather than failing and outputting an error message on the
I2C transactions that follow.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
BeagleBoard.org BeagleBone AI rev A1 does not include a board
identifier I2C EEPROM due to a design oversight. These boards have
been put into production and are generally available now.
The board identifier information, however, has been included in the
second eMMC linear boot partition (/dev/mmcblk1boot1).
This patch works by:
* First, looking for a board identifier I2C EEPROM and if not found,
* Then seeing if the boot mode matches BeagleBone AI with eMMC in the
boot chain to make sure we don't enable eMMC pinmuxes on boards
that don't support it, and
* Finally, initializes the eMMC pins and reading the header.
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Cc: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
These functions do not use driver model but are still used. Move them to a
new eeprom.h header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
There is an option to enable the board detection for TI platforms.
If this is option is not set, there is no reason to set the EEPROM
bus address or chip address.
This patch makes both EEPROM_BUS_ADDRESS and EEPROM_CHIP_ADDRESS
depend on TI_I2C_BOARD_DETECT.
Signed-off-by: Adam Ford <aford173@gmail.com>
The AM654x EVM based on the TI K3 family of SoCs has an updated board
detection EEPROM structure that contains a TLV record of dedicated MAC
addresses rather than a range of MAC addresses as it was used on earlier
platforms such as DRA7. Add a basic function that allows us setting up
Ethernet MAC addresses into the U-Boot environment based on the MAC
address record contained in the common TI EEPROM structure.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The AM654x EVM based on the TI K3 family of SoCs have an updated board
detection EEPROM structure, now comprising variable-sized TLV-type
records, containing a superset of what is already being provided on
earlier platforms such as DRA7. Add basic support for parsing the new
data structures contained on the base board into the common TI EEPROM
structure while also providing infrastructure that can be used later on
to parse data from additional EEPROMs such as the ones that are used on
daughtercards for this platform.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C
API when DM_I2C is used. The goal is to eventually remove DM_I2C_COMPAT
when all I2C "clients" have been migrated to use the DM API.
This a step in that direction for the TI based platforms.
Build tested with buildman:
buildman -dle am33xx ti omap3 omap4 omap5 davinci keystone
boot tested with:
am335x_evm, am335x_boneblack, am335x_boneblack_vboot (DM version),
am57xx_evm, dra7xx_evm, k2g_evm, am437x_evm
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The EEPROM reading in the board detection code is done through legacy
I2C functions which on platforms using DM_I2C this functionality is
provided via the CONFIG_DM_I2C_COMPAT layer. To allow newer platforms
to use the board detection code without relying on CONFIG_DM_I2C_COMPAT
go ahead and add an I2C handling implementation that directly uses the
I2C DM functionality.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to
drivers/fastboot.
Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants
FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split
USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing
behaviour.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we support multiple environment drivers but there is not way to
select between them at run time. Also settings related to the position and
size of the environment area are global (i.e. apply to all locations).
Until these limitations are removed we cannot really support more than one
environment location. Adjust the location to be a choice so that only one
can be selected. By default the environment is 'nowhere', meaning that the
environment exists only in memory and cannot be saved.
Also expand the help for the 'nowhere' option and move it to the top since
it is the default.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Move all of the imply logic to default X if Y so it works again]
Signed-off-by: Tom Rini <trini@konsulko.com>
When we have MMC available we assume that we want to put the env as a
file on FAT.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
When the EEPROM is first read its contents are stored in memory as a
cache to avoid further I2C operations. To determine if the EEPROM was
previously read the easiest way is to check the memory to see if the
EEPROM's magic header value is set. Create a new function that can
determine if the EEPROM was previously read or not without having to
perform a I2C transaction.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In some situations the EEPROM used for board detection may not be
programmed or simply programmed incorrectly. Therefore, it may be
necessary to "simulate" reading the contents of the EEPROM to set
appropriate variables used in the board detection code.
This may also be helpful in certain boot modes where doing i2c reads
may be costly and the config supports running only a specific board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Franklin S Cooper Jr. <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently these (board agnostic) commands cannot be selected using
menuconfig and friends. Fix this the obvious way. As part of this,
don't muddle the meaning of CONFIG_HASH_VERIFY to mean both 'hash -v'
and "we have a hashing command" as this makes the Kconfig logic odd.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
[trini: Re-apply, add imply for a few cases, run moveconfig.py, also
migrate CRC32_VERIFY]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_EEPROM
CONFIG_CMD_EEPROM_LAYOUT
CONFIG_EEPROM_LAYOUT_HELP_STRING
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework Kconfig logic slightly, define EEPROM location on TI eval
platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
In non DM I2C read operations the address length passed in during a read
operation will be used automatically. However, in DM I2C the address length
is set to a default value of one which causes problems when trying to
perform a read with a differing alen. Therefore, before the first read in a
series of read operations set the alen to the correct value.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reading from the I2C EEPROM used typically requires using an address length
of 2. However, when using DM for I2C the default address length used is 1.
To fix this introduce a new function that allows the address length to be
changed. The logic to do so was copied from cmd/i2c.c.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Instead of defining command options in every defconfig,
define a common Kconfig symbol that consolidates all command
options that are supported by any TI platform. Also use imply
keyword so that that specific option can be disabled if
not required.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In stead of defining the board EEPROM address in the board headers
let's define them in the board config files and make them
configurable by Kconfig.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Keystone and OMAP platforms will need this to set ethernet
MAC addresses from board EEPROM.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Non OMAP platforms i.e. Keystone will also need to use the board
EEPROM helpers so let's make the macro platform independent.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The option that we had set in board/ti/common/Kconfig as default y are
best done with imply under the appropriate main Kconfig option instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
The bootrom may corrupt the area of SRAM used to store the ti_common_eeprom
structure. This patch makes sure that it's always read after a reset, even
if a valid MAGIC number is found in the SRAM.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Current logic for query of revision, board_name, config returns
NULL. Users of these functions do a direct strncmp to compare.
Unfortunately, as per conventions require two valid strings to compare
against and the current implementation causes a crash when compared
with NULL.
We'd still like to maintain the simplistic usage of these APIs instead
of redundant if (string) res=strncmp(fn(),"cmp",n); flowing all over
the place.
Hence, since the version, name and config is already pre-initialized
with empty string, just dont check for invalid header in the first
place and return the empty string to the caller.
Reported-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Correct was'nt -> wasn't typo]
Signed-off-by: Tom Rini <trini@konsulko.com>
config should have been initialized along with others as defaults.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We should have used TI_DEAD_EEPROM_MAGIC in the first place.
Fixes: d3b98a9eb9 ("ti: common: dra7: Add standard access for board description EEPROM")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
