Commit graph

6547 commits

Author SHA1 Message Date
Peng Fan
f15ece388f imx: imx6ul: disable POR_B internal pull up
>From TO1.1, SNVS adds internal pull up control for POR_B,
the register filed is GPBIT[1:0], after system boot up,
it can be set to 2b'01 to disable internal pull up.
It can save about 30uA power in SNVS mode.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 19:37:39 +02:00
Peng Fan
2ee4065571 imx-common: enlarge mux width to 4
For i.MX6, the mux width is 4, not 3. So enlarge the width.
IOMUX_CONFIG_LPSR is changed from 0x8 to 0x20 to not use bit 3 of mux.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 19:37:28 +02:00
Stefan Agner
81c4eccb55 imx: mx6: fix USB bmode to use reserved value
Currently the bmode "usb" uses BOOT_CFG1 to 0x01, -which means
BOOT_CFG1[7:4] is set to b0000. According to Table 8-7 Boot
Device Selection this is NOR/OneNAND and not Reserved.

Use 0x10 which leads to b0001, which is a Reserved boot device.
With that the SoC reliably falls back to the serial loader.

Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Troy Kisky <troy.kisky@boundarydevices.com>
2016-10-04 19:31:23 +02:00
Peng Fan
55a42b33f2 arm: imx: add i.MX6ULL 14x14 EVK board support
Add i.MX6ULL EVK board support:
Add device tree file, which is copied from NXP Linux.
Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR.
The uart iomux settings are still keeped in board file.

Boot Log:
U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800)

CPU:   Freescale i.MX6ULL rev1.0 at 396MHz
CPU:   Commercial temperature grade (0C to 95C) at 15C
Reset cause: POR
Model: Freescale i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM:  512 MiB
MMC:   initialized IMX pinctrl driver
FSL_SDHC: 0, FSL_SDHC: 1
In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
=> mmc dev 1
switch to partitions #0, OK
mmc1 is current device

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:42:07 +02:00
Peng Fan
b0a8e45451 arm: dts: add device tree for i.MX6ULL
Add device tree for i.MX6ULL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:01 +02:00
Peng Fan
f8ca22b8de arm: dts: imx6ull: add pinctrl defines
Add pinctrl defines for NXP i.MX 6ULL.
Since i.MX6ULL reuses some definitions of i.MX6UL,
also add i.MX6UL pinctrl defines from linux kernel commit (29b4817d401).

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:01 +02:00
Peng Fan
07e1c0ae83 imx: iomux: fix snvs usage for i.MX6ULL
SNVS TAMPER pin and BOOT MODE pins are in SNVS IOMUXC module,
not in IOMUXC, so correct the related registers' offset.

Use IOMUX_CONFIG_LPSR flag for these pins, so we can differentiate
them from iomuxc pins.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: "Benoît Thébaudeau" <benoit.thebaudeau.dev@gmail.com>
2016-10-04 15:41:01 +02:00
Peng Fan
5b66482d44 imx: imx6ull: adjust the ldo 1.2v bandgap voltage
Per to design team, on i.MX6UL, the LDO 1.2V bandgap voltage
is 30mV higher, so we need to adjust the REFTOP_VBGADJ(anatop
MISC0 bit[6:4]) setting to 2b'110.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:01 +02:00
Peng Fan
2d4bbd01a1 imx: mx6ull: Add AIPS3 initialization
Since the mx6ull adds the AIPS3, so enable its initialization.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:01 +02:00
Peng Fan
bdfb2d4db2 imx: mx6ull: Update memory map address
Update memory map address for mx6ull.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:00 +02:00
Peng Fan
3974b7f6e0 imx: mx6ull: update clock settings and CCM register map
Update Clock settings and CCM register map for i.MX6ULL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:00 +02:00
Peng Fan
b4714616a0 imx: mx6ull: adjust POR_B setting for i.MX6ULL
Adjust POR_B settings on i.MX6ULL according to IC design
team's suggestion:

2'b00 :  always PUP100K
2'b01 :  PUP100K when PMIC_ON_REQ || SOC_NOT_FAIL
2'b10 :  always disable PUP100K
2'b11 :  PDN100K when SOC_FAIL, PUP100K when SOC_NOT_FAIL -- recommended setting

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:00 +02:00
Peng Fan
6615da4da3 imx: mx6ull: misc soc update
Update misc SOC related settings for i.MX6ULL, such as FEC mac address,
cpu speed grading and mmdc channel mask clearing.

Also update s_init to skip pfd reset.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:00 +02:00
Peng Fan
00ffa56d4b imx: mx6ul: using runtime check when configuring PMIC_STBY_REQ
Since MX6ULL select MX6UL, we can not use IS_ENABLED(CONFIG_MX6UL) here,
because this piece code is only for i.MX6UL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:00 +02:00
Peng Fan
cdf33c9403 imx: mx6ull: skip setting ahb clock
Rom already initialized clock at 396M and 132M for arm core and ahb,
so skip setting them again in U-Boot.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:00 +02:00
Peng Fan
988acd2d4c imx: timer: update gpt driver for i.MX6ULL
The i.MX6ULL's GPT supportting taking OSC as clock source.
Add i.MX6ULL support.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:00 +02:00
Peng Fan
bbd1b07d30 imx-common: introduce is_mx6ull
Introduce is_mx6ull macro.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:00 +02:00
Ye Li
51db46035c imx: mx6ull: add kconfig entry for MX6ULL
i.MX6ULL is derivative from i.MX6UL, so select MX6UL for MX6ULL.
If need to differenate MX6ULL from MX6UL, use CONFIG_MX6ULL

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:00 +02:00
Peng Fan
65ce54be8e imx: mx6ull: add mx6ull major cpu type
Add i.MX6ULL major cpu type.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-10-04 15:40:59 +02:00
Peng Fan
7b4dd81666 imx: mx6ull: add iomux header file
Add iomux header file for i.MX6ULL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-10-04 15:40:59 +02:00
Filip Brozovic
514a0f4b68 imx: iomux-v3: fix pad setup on i.MX6DQP when CONFIG_MX6QDL is defined
The CPU detection macro is_mx6dq returns 0 on an i.MX6DQP, so we need to
check for it explicitly in order to correctly initialize the pads when
CONFIG_MX6QDL is defined.

Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
2016-10-04 12:01:14 +02:00
Tom Rini
51b4a639e4 Merge git://git.denx.de/u-boot-rockchip 2016-10-03 09:09:29 -04:00
Andrew F. Davis
ba84e6ae1f ti: omap-common: Allow AM33xx devices to be built securely
Like OMAP54xx and AM43xx family SoCs, AM33xx based SoCs have high
security enabled models. Allow AM33xx devices to be built with
HS Device Type Support.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-10-02 08:10:02 -04:00
Andrew F. Davis
7e5a0bfbd2 am33xx: config.mk: Fix option used to enable SPI SPL image type
The option SPL_SPI_SUPPORT is used to enable support in SPL for loading
images from SPI flash, it should not be used to determine the build type
of the SPL image itself. The ability to read images from SPI flash does
not imply the SPL will be booted from SPI flash.

Unconditionally build SPI flash compatible SPL images.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-02 08:10:00 -04:00
Andrew F. Davis
9eda25181d am33xx: config.mk: Add support for additional secure boot image types
Depending on the boot media, different images are needed
for secure devices. The build generates u-boot*_HS_* files
as appropriate for the different boot modes.

For AM33xx devices additional image types are needed for
various SPL boot modes as the ROM checks for the name of
the boot mode in the file it loads.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-10-02 08:09:59 -04:00
Andrew F. Davis
b39a9ade5c Kconfig: Separate AM33XX SOC config from target board config
The config option AM33XX is used in several boards and should be
defined as a stand-alone option for this SOC. We break this out
from target boards that use this SoC and common headers then enable
AM33XX on in all the boards that used these targets to eliminate any
functional change with this patch.

This is similar to what has already been done in
9de852642cae ("arm: Kconfig: Add support for AM43xx SoC specific Kconfig")
and is done for the same reasons.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-02 08:09:58 -04:00
Daniel Allred
6696139409 ARM: omap5: add fdt secure dram reservation fixup
Adds a secure dram reservation fixup for secure
devices, when a region in the emif has been set aside
for secure world use. The size is defined by the
CONFIG_TI_SECURE_EMIF_TOTAL_REGION_SIZE config option.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-02 08:09:57 -04:00
Daniel Allred
501f0ef304 ARM: DRA7: Add secure emif setup calls
After EMIF DRAM is configured, but before it is used,
calls are made on secure devices to reserve any configured
memory region needed by the secure world and then to lock the
EMIF firewall configuration. If any other firewall
configuration needs to be applied, it must happen before the
lock call.

Signed-off-by: Daniel Allred <d-allred@ti.com>
2016-10-02 08:09:56 -04:00
Daniel Allred
6d132b2b09 arm: omap5: secure API for EMIF memory reservations
Create a few public APIs which rely on secure world ROM/HAL
APIs for their implementation. These are intended to be used
to reserve a portion of the EMIF memory and configure hardware
firewalls around that region to prevent public code from
manipulating or interfering with that memory.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-02 08:09:55 -04:00
Daniel Allred
4c854b6199 ti: omap5: Add Kconfig options for secure EMIF reservations
Adds start address and size config options for setting aside
a portion of the EMIF memory space for usage by security software
(like a secure OS/TEE). There are two sizes, a total size and a
protected size. The region is divided into protected (secure) and
unprotected (public) regions, that are contiguous and start at the
start address given. If the start address is zero, the intention
is that the region will be automatically placed at the end of the
available external DRAM space.

Signed-off-by: Daniel Allred <d-allred@ti.com>
2016-10-02 08:09:51 -04:00
Jacob Chen
67171e13a3 rockchip: add boot-mode support for rk3288, rk3036
rockchip platform have a protocol to pass the the kernel reboot mode to bootloader
by some special registers when system reboot. In bootloader we should read it and take action.

We can only setup boot_mode in board_late_init becasue "setenv" need env setuped.
So add CONFIG_BOARD_LATE_INIT to common header and use a entry "rk_board_late_init"
to replace "board_late_init" in board file.

Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-10-01 18:36:55 -06:00
Jacob Chen
f48f2b729b rockchip: move common function from board-file to rk3036-board.c
To keep it same with 3288

Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-10-01 18:36:55 -06:00
Jacob Chen
cd77fd1b43 rockchip: rename board.c to rk3288-board.c
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-10-01 18:36:55 -06:00
Xu Ziyuan
c12777a625 rockchip: miniarm: remove eMMC support
The latest rk3288-miniarm board doesn't have eMMC device, so remove it.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-10-01 18:35:01 -06:00
Kever Yang
c553de90bd dts: evb-rk3399: add init voltage node for vdd-center
Add a regulator-init-microvolt for vdd_center regulator
so that we can get a init value for driver probe.
Not like pmic regulator, the PWM regulator do not have a
known default output value, so we would like to init the
regulator when driver probe.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-10-01 18:35:01 -06:00
Kever Yang
8d29e3a4c4 Kconfig: rockchip: enable DM_PWM and DM_REGULATOR
Enable DM_PWM and DM_REGULATOR on rockchip SoCs.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-10-01 18:35:01 -06:00
Kever Yang
d840daf4c2 rockchip: rkpwm: fix the register sequence
Reference to kernel source code, rockchip pwm has three
type, we are using v2 for rk3288 and rk3399, so let's
update the register to sync with pwm_data_v2 in kernel.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-10-01 18:35:01 -06:00
Kever Yang
8389dcbf98 rockchip: rk3399: update PPLL and pmu_pclk frequency
Update PPLL to 676MHz and PMU_PCLK to 48MHz, because:
1. 48MHz can make sure the pwm can get exact 50% duty ratio, but 99MHz
can not,
2. We think 48MHz is fast enough for pmu pclk and it is lower power cost
than 99MHz,
3. PPLL 676 MHz and PMU_PCLK 48MHz are the clock rate we are using
internally for kernel,it suppose not to change the bus clock like pmu_pclk
in kernel, so we want to change it in uboot.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-10-01 18:35:01 -06:00
Sandy Patterson
230e0e09da Disable SPL_MMC_SUPPORT if ROCKCHIP_SPL_BACK_TO_BROM is enabled.
Default SPL_MMC_SUPPORT to false when ROCKCHIP_SPL_BACK_TO_BROM is enabled.

Acked-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Sandy Patterson <apatterson@sightlogix.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-10-01 18:35:01 -06:00
Sandy Patterson
427351dc1d rockchip: Fix SPL console output when ROCKCHIP_SPL_BACK_TO_BROM is enabled
Move back_to_bootrom() call later in SPL init so that the console is
initialized and printouts happen.

Currently when ROCKCHIP_SPL_BACK_TO_BROM is enabled there is no console
output from the SPL init stages.

I wasn't sure exactly where this should happen, so if we are set to do
run spl_board_init, then go back to bootrom there after
preloader_console_init(). Otherwise fall back to old behavior of doing
it in board_init_f.

Signed-off-by: Sandy Patterson <apatterson@sightlogix.com>
Acked-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-10-01 18:35:01 -06:00
Xu Ziyuan
2179a07c0c rockchip: rk3288: sdram: fix DDR address range
The all current Rockchip SoCs supporting 4GB of ram have problems
accessing the memory region 0xfe000000~0xff000000. Actually, some IP
controller can't address to, so let's limit the available range.

This patch fixes a bug which found in miniarm-rk3288-4GB board. The
U-Boot was relocated to 0xfef72000, and .bss variants was also
relocated, such as do_fat_read_at_block. Once eMMC controller transfer
data to do_fat_read_at_block via DMA, DMAC can't access more than
0xfe000000. So that DMAC didn't work sane.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-10-01 18:35:01 -06:00
Lokesh Vutla
5d21406516 ARM: keystone2: Add support for parsing monitor header
Given that boot monitor image is being generated to a specific target location
depending on the SoC and U-boot relies on addr_mon env variable to be aligned
with boot monitor target location. When ever the target address gets updated in
boot monitor, it is difficult to sync between u-boot and boot monitor and also
there is no way to update user that boot monitor image is updated.

To avoid this problem, boot monitor image is being generated with mkimage
header. Adding support in mon_install command for parsing this header.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-01 20:05:10 -04:00
Lokesh Vutla
e1ae357d4b board: k2g: Enable ECC byte lane
Enable ECC byte lane for k2g-evm

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-01 20:05:07 -04:00
Tom Rini
fe4ba689a0 Merge branch 'master' of git://git.denx.de/u-boot-usb
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	include/configs/dra7xx_evm.h
2016-09-30 21:58:44 -04:00
Sanchayan Maity
727f790829 ARM: dts: vf-colibri: Enable USB device tree node for Colibri Vybrid
Enable USB device tree node for Toradex Colibri Vybrid module.

Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
2016-09-27 23:30:24 +02:00
Sanchayan Maity
5aaad0647a ARM: dts: vf: Add device tree node for USB on Vybrid
Add device tree node for USB peripheral on Vybrid.

Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
2016-09-27 23:30:23 +02:00
B, Ravi
6f8387f120 dra7x: boot: add dfu bootmode support
This patch enables the DFU boot mode support
for dra7x platform.

Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-27 23:30:20 +02:00
Tom Rini
40e1236afe Merge branch 'master' of git://git.denx.de/u-boot-tegra 2016-09-27 12:47:25 -04:00
Stephen Warren
8e5d804f89 ARM: tegra: flush caches via SMC call
On Tegra186, it is necessary to perform an SMC to fully flush all caches;
flushing/cleaning by set/way is not enough. Implement the required hook
to make this happen.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27 09:11:03 -07:00
Stephen Warren
6dca554f23 ARM: tegra: fix ULPI PHY on Ventana and Seaboard
Commit ce02a71c23 "tegra: dts: Sync tegra20 device tree files with
Linux" enabled the ULPI USB port on Ventana, but made no attempt to ensure
that U-Boot code could handle this. In practice, various code is missing,
and various configuration options are not enabled, which causes U-Boot to
hang when attempting to initialize this USB port. This patch enables ULPI
PHY support on Ventana, and adds the required pinmux setup for the port to
operate. Note that Ventana is so similar to Seaboard that this change is
made in the Seaboard board file, which is shared with Ventana.

Seaboard also has the ULPI USB port wired up in hardware, although to an
internal port that often doesn't have anything attached to it. However,
the DT nodes for the USB controller and PHY had different status property
values, so the port was not initialized by U-Boot. Fix this inconsistency,
and enable the ULPI port, just like in the Linux kernel DT. This likewise
requires enabling ULPI support in the Seaboard defconfig.

Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27 09:11:03 -07:00