The (upstream) changes to break up SYS_MALLOC_F_LEN for the full
U-Boot and the SPL stage, break TPL (if simple malloc is enabled in
TPL).
This adds support for a TPL-variant of SYS_MALLOC_F_LEN:
- adds TPL_SYS_MALLOC_F_LEN
- rewrites a test for CONFIG_SPL_SYS_MALLOC_F_LEN to access
CONFIG_VAL(SYS_MALLOC_F_LEN)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_TEXT_BASE
The includes, whitelist, etc. were left for now but I don't get any
build errors or warnings on the omap3_logic_defconfig or
am3517_evm_defconfig builds I tried.
Signed-off-by: Adam Ford <aford173@gmail.com>
Some platforms have very limited SRAM to run SPL code, so there may
not be the same amount space for a malloc pool before relocation in
the SPL stage as the normal U-Boot stage.
Make SPL and (the full) U-Boot stage use independent SYS_MALLOC_F_LEN,
so the size of pre-relocation malloc pool can be configured memory
space independently.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[fixed up commit-message:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
trini: Make Kconfig SPL_xxx entires only show if SPL, so that we don't
get Kconfig errors on platforms without SPL, ie sandbox (without SPL).
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit 94e3c8c4fd ("crypto/fsl - Add progressive hashing support
using hardware acceleration.") created entries for CONFIG_SHA1,
CONFIG_SHA256, CONFIG_SHA_HW_ACCEL, and CONFIG_SHA_PROG_HW_ACCEL.
However, no defconfig has migrated to it. Complete the move by first
adding additional logic to various Kconfig files to select this when
required and then use the moveconfig tool. In many cases we can select
these because they are required to implement other drivers. We also
correct how we include the various hashing algorithms in SPL.
This commit was generated as follows (after Kconfig additions):
[1] tools/moveconfig.py -y SHA1 SHA256 SHA_HW_ACCEL
[2] tools/moveconfig.py -y SHA_PROG_HW_ACCEL
Note:
We cannot move SHA_HW_ACCEL and SHA_PROG_HW_ACCEL simultaneously
because there is dependency between them.
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We rename CONFIG_FIT_DISABLE_SHA256 to CONFIG_FIT_ENABLE_SHA256_SUPPORT which
is enabled by default and now a positive option. Convert the handful of boards
that were disabling it before to save space.
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Lukasz Dalek <luk0104@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Allwinner SoCs with 64-bit cores use an ARM Trusted Firmware binary,
which needs to be loaded alongside U-Boot proper.
Set the respective Kconfig options to let them select this feature and
also automatically build the FIT image.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Rename Kconfig path to arch/arm/mach-sunxi/Kconfig]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Some platforms require more complex U-Boot images than we can easily
generate via the mkimage command line, for instance to load additional
image files.
Introduce a CONFIG_SPL_FIT_SOURCE and CONFIG_SPL_FIT_GENERATOR symbol,
which can either hold an .its source file describing the image layout,
or, in the second case, a generator tool (script) to create such
a source file. This script gets passed the list of device tree files
from the CONFIG_OF_LIST variable.
A platform or board can define either of those in their defconfig file
to allow an easy building of such an image.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
SPL_FIT obviously requires libfdt in SPL, so let Kconfig express that by
selecting SPL_OF_LIBFDT.
Also make the actual options that users want (SPL signature and SPL FIT
loading) visible in the menu and let them select the SPL_FIT as a
requirement.
Also remove the now redundant SPL_OF_LIBFDT from those Kconfigs that had
it in for the SPL FIT loading feature.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[Remove change from configs/evb-rk3399_defconfig]
Signed-off-by: Jagan Teki <jagan@openedev.com>
This patch makes SYS_TEXT_BASE a config option for Keystone2
so that it can be used to load u-boot at different addresses
on secure and non-secure Keystone2 devices.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
FIT images require MD5 support to verify image checksums. So far this
was expressed by defining a CPP symbol in image.h. Since MD5 is now a
first class Kconfig citizen, express that in Kconfig instead.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add kconfig file to enable API support
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This feature is inspired by /proc/config.gz of Linux. In Linux,
if CONFIG_IKCONFIG is enabled, the ".config" file contents are
embedded in the kernel image. If CONFIG_IKCONFIG_PROC is also
enabled, the ".config" contents are exposed to /proc/config.gz.
Users can do "zcat /proc/config.gz" to check which config options
are enabled on the running kernel image.
The idea is almost the same here; if CONFIG_CMD_CONFIG is enabled,
the ".config" contents are compressed and saved in the U-Boot image,
then printed by the new command "config".
The usage is quite simple. Enable CONFIG_CMD_CONFIG, then run
> config
from the command line interface. The ".config" contents will be
printed on the console.
This feature increases the U-Boot image size by about 4KB (this is
mostly due to the gzip-compressed .config file). By default, it is
enabled only for Sandbox because we do not care about the memory
footprint on it. Of course, this feature is architecture agnostic,
so you can enable it on any board if the image size increase is
acceptable for you.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly
update all of the config files we must also update CMD_PART and CMD_GPT to also
be in Kconfig in order to avoid complex logic elsewhere to update all of the
config files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Use the generic "distro" boot framework to enable automatic DHCP boot.
MMC and USB are not yet implemented, so this is the only boot option.
The fdt and kernel addresses are adopted from downstream; ramdisk and
scriptaddr addresses were chosen arbitrarily.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Some refactoring of the top-level Kconfig file which includes:
* using "if" to remove numerous identical dependency tests
* reordering config entries to group related ones
* spelling and grammar fixes
There should be no functional changes, only aesthetic ones.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
This enables suitable commands needed for booting general purpose
Linux distribution. This is required for example if we want to use PXE
or DHCP as default boot targets, symbols no longer enabled by
config_distro_defaults.h .
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Currently, CMD_PXE is forcibly enabled in config_distro_defaults.h, so
that general purpose distributions can rely on it being defined. This
header is included, under conditions or not, by various archs or
famillies of archs / SoCs.
However, it is very possible that boards based on those SoCs will not
have a physical ethernet connector at all, even if the have a MAC; for
example, the Nanopi Neo AIR (sunxi H3) does not. It is also possible
that network booting is absolutely not necessary for a device.
However, it is not possible to disable the PXE command, as it is
forcibly enabled and is non-configurable.
But it turns out we already have a config option to build a distro-ready
image, in the name of DISTRO_DEFAULTS.
Move CMD_PXE out of the hard-coded config_distro_defaults.h into a
Kconfig option, that gets selected by DISTRO_DEFAULTS when it is set.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Joe Hershberger <joe.hershberger@ni.com>
[trini: Make it select MENU, run moveconfig.py]
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of platforms had been using the distro default feature before
it was moved to Kconfig but did not enable the new Kconfig option when
it was enabled. This caused a regression in terms of features and this
introduces breakage when more things move to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit e2f88dfd2d ("libfdt: Introduce new ARCH_FIXUP_FDT option")
allows us to skip memory setup of DTB, but a problem for ARM is that
spin_table_update_dt() and psci_update_dt() are skipped as well if
CONFIG_ARCH_FIXUP_FDT is disabled.
This commit allows us to skip only fdt_fixup_memory_banks() instead
of the whole of arch_fixup_fdt(). It will be useful when we want to
use a memory node from a kernel DTB as is, but need some fixups for
Spin-Table/PSCI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed build error for x86:
Signed-off-by: Simon Glass <sjg@chromium.org>
The DFU Kconfig menu entries should be part of the SPL
Kconfig file. Also avoid using the top level Makefile by
moving the config dependent build artifacts to the driver/
and driver/usb/gadget/ Makfiles.
With that, DFU can be built again in SPL if
CONFIG_SPL_DFU_SUPPORT is enabled.
Fixes: 6ad6102246 ("usb:gadget: Disallow DFU in SPL for now")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Most new systems in U-Boot these days make use of the generic "distro"
framework which allows a user to have U-Boot scan for a bootable OS
on all available media types.
This patch extends the LS2080ARDB board to use that framework if the
hard coded NOR flash location does not contain a bootable image.
Signed-off-by: Alexander Graf <agraf@suse.de>
Traditionally the DFU support is available only
as part 2nd stage boot loader(u-boot) and DFU
is not supported in SPL.
The SPL-DFU feature is useful for boards which
does not have MMC/SD, ethernet boot mechanism
to boot the board and only has USB inteface.
This patch add DFU support in SPL with RAM
memory device support to load and execute u-boot.
And then leverage full functionality DFU in
u-boot to flash boot inital binary images to
factory or bare-metal boards to memory devices
like SPI, eMMC, MMC/SD card using USB interface.
This SPL-DFU support can be enabled through
Menuconfig->Boot Images->Enable SPL-DFU support
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This reverts commit 90c08d9e08.
I took a closer look at this after the commit was applied, and found
CONFIG_SYS_MALLOC_F_LEN=0x2000 was too much. 8KB memory for SPL is
actually too big for some boards. Perhaps 0x800 is enough, but the
situation varies board by board.
Let's postpone our decision until we come up with a better idea.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If both SPL_DM and SPL_OF_CONTROL are enabled, SPL needs to bind
several devices, but CONFIG_SYS_MALLOC_F_LEN=0x400 is apparently
not enough. Increase the default to 0x2000 for the case. This
will be helpful for shorter defconfigs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The 'bootz' command is really only for ARM32 Linux Kernel 'zImage' files
but has also been adapted for testing with sandbox. Given that sandbox
is a test platform, don't add that logic under DISTRO_DEFAULTS.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This command is used to boot ARM64 Linux.
I made DISTRO_DEFAULTS select this option for ARM64 to respect
include/config_distro_defaults.h.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit allows injecting a board/platform/device-specific post-
processing function into the FIT image data loading process, which can
include modifying the size and altering the starting source address of
an image data artifact. This might be desired to do things like strip
headers or footers attached to the images before they were packaged into
the FIT, or to perform operations such as decryption or authentication.
Introduce new configuration option CONFIG_FIT_IMAGE_POST_PROCESS to
allow controlling this feature. If enabled, a platform-specific post-
process function must be provided.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We need to ensure that CONFIG_PHYS_64BIT is configured via Kconfig so
that it is always available to the build system. Otherwise we can run
into cases where we have inconsistent sizes of certain attributes.
Ravi Babu reported offset mismatch of struct dwc3 across files since
commit 95ebc253e6 ("types.h: move and redefine resource_size_t").
Since the commit, resource_addr_t points to phys_addr_t, whose size
is dependent on CONFIG_PHYS_64BIT for ARM architecture.
I tried my best to use "select" where possible (for example, ARMv8
architecture) because I think this kind of option is generally user-
unconfigurable. However, I see some of PowerPC boards have 36BIT
defconfigs as well as 32BIT ones. I moved CONFIG_PHYS_64BIT to the
defconfigs for such boards.
CONFIG_36BIT is no longer referenced, so all of the defines were
removed from CONFIG_SYS_EXTRA_OPTIONS.
Fixes: 95ebc253e6 ("types.h: move and redefine resource_size_t")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add new Kconfig option to disable arch_fixup_fdt() calls for cases where
U-Boot shouldn't update memory setup in DTB file.
One example of usage of this option is to boot OS with different memory
setup than U-Boot use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Simon Glass <sjg@chromium.org>
Sometimes it is useful to build tools with debugging information included so
that line-number information is available when run under gdb. Add a Kconfig
option to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The next stage boot loader image and the selected FDT can be post-
processed by board/platform/device-specific code, which can include
modifying the size and altering the starting source address before
copying these binary blobs to their final destination. This might be
desired to do things like strip headers or footers attached to the
images before they were packaged into the FIT, or to perform operations
such as decryption or authentication. Introduce new configuration
option CONFIG_SPL_FIT_IMAGE_POST_PROCESS to allow controlling this
feature. If enabled, a platform-specific post-process function must
be provided.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
DISTRO_DEFAULTS is intended to mirror / replace
include/config_distro_defaults.h.
The intend is for boards which include this file to select this from
their Kconfig files and when moving setting to Kconfig which are #define-ed
in config_distro_defaults.h to select this from DISTRO_DEFAULTS so that
boards which have selected DISTRO_DEFAULTS will keep the same configuration
as before without needing any defconfig file changes.
The initial list of selected things matches all settings recently removed
from config_distro_defaults.h because they have been converted to Kconfig,
with the exception of CMD_ELF and CMD_NET, which have a default of y, if
the default of these ever changes they should be selected by DISTRO_DEFAULTS
too.
For testing and example purposes this commit also converts ARCH_SUNXI
to use DISTRO_DEFAULT instead of selecting everything it needs itself.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This allows a board to configure verified boot within the SPL using
a FIT or FIT with external data. It also allows the SPL to perform
signature verification without needing relocation.
The board configuration will need to add the following feature defines:
CONFIG_SPL_CRYPTO_SUPPORT
CONFIG_SPL_HASH_SUPPORT
CONFIG_SPL_SHA256
In this example, SHA256 is the only selected hashing algorithm.
And the following booleans:
CONFIG_SPL=y
CONFIG_SPL_DM=y
CONFIG_SPL_LOAD_FIT=y
CONFIG_SPL_FIT=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_SPL_OF_LIBFDT=y
CONFIG_SPL_FIT_SIGNATURE=y
Signed-off-by: Teddy Reed <teddy.reed@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
Acked-by: Sumit Garg <sumit.garg@nxp.com>
Move CONFIG_SYS_TEXT_BASE to Kconfig, and add default values in board
Kconfig files matching what was present in their config headers. This
will make it cleaner to conditionalise the value for Malta based on 32
vs 64 bit builds.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This provides a way to load a FIT containing U-Boot and a selection of device
tree files. The board can select the correct device tree by probing the
hardware. Then U-Boot is started with the selected device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
There are a lot of unrelated files in common, including all of the commands.
Moving them into their own directory makes them easier to find and is more
logical.
Some commands include non-command code, such as cmd_scsi.c. This should be
sorted out at some point so that the function can be enabled with or without
the associated command.
Unfortunately, with m68k I get this error:
m68k: + M5329AFEE
+arch/m68k/cpu/mcf532x/start.o: In function `_start':
+arch/m68k/cpu/mcf532x/start.S:159:(.text+0x452): relocation truncated to fit: R_68K_PC16 against symbol `board_init_f' defined in .text.board_init_f section in common/built-in.o
I hope someone can shed some light on what this means. I hope it isn't
depending on the position of code in the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
This is how CONFIG options are defined by Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
For historical reason, CONFIG_SYS_TEXT_BASE has been specified
in various ways:
[1] by board/${VENDOR}/${BOARD}/config.mk
[2] by CONFIG_SYS_EXTRA_OPTIONS
(This was "options" field of boards.cfg before Kconfig conversion)
[3] by include/configs/${BOARD}.h
[4] by configs/${BOARD}_defconfig
Most of M68K boards use either [1] or [2], both of which we want to
deprecate. Switch them into [4], which is the newest way (Kconfig).
We still allow [3] too, because it is still used by many boards and
we expect much time for conversion.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Angelo Dureghello <angelo at sysam.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present in SPL we place the device tree immediately after BSS. This
avoids needing to copy it out of the way before BSS can be used. However on
some boards BSS is not placed with the image - e.g. it can be in RAM if
available.
Add an option to tell U-Boot that the device tree should be placed at the
end of the image binary (_image_binary_end) instead of at the end of BSS.
Note: A common reason to place BSS in RAM is to support the FAT filesystem.
We should update the code so that it does not use so much BSS.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
malloc_simple uses a part of the stack as heap, initially it uses
SYS_MALLOC_F_LEN bytes which typically is quite small as the initial
stacks sits in SRAM and we do not have that much SRAM to work with.
When DRAM becomes available we may switch the stack from SRAM to DRAM
to give use more room. This commit adds support for also switching to
a new bigger malloc_simple heap located in the new stack.
Note that this requires spl_init to be called before spl_relocate_stack_gd
which in practice means that spl_init must be called from board_init_f.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
common/dlmalloc.c is quite big, both in .text and .data usage, therefor
on some boards the SPL is build to use only malloc_simple.c and not the
dlmalloc.c code. This is done in various include/configs/foo.h with the
following construct:
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif
This commit introduces a SPL_MALLOC_SIMPLE Kconfig bool which allows
selecting this functionality through Kconfig instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
