Commit graph

13841 commits

Author SHA1 Message Date
Quentin Schulz
05bbd676a7 net: phy: mscc: add support for VSC8574 PHY
The VSC8574 PHY is a 4-port PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with
the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and
can set the blinking pattern of each of its 4 LEDs, supports SyncE as
well as HP Auto-MDIX detection.

This adds support for 10/100/1000BASE-T and SGMII/QSGMII link with the
MAC.

The VSC8574 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.

The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.

Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:59 -06:00
Quentin Schulz
b5bca65e19 net: phy: mscc: factorize part of config function for VSC8584
Part of the config is common between the VSC8584 and the VSC8574, so to
prepare for the upcoming support of VSC8574, use the phy_device.priv
pointer that will keep the function that holds code that is PHY-specific
and that should be called during config function.

Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:58 -06:00
Quentin Schulz
04087fc494 net: phy: mscc: add support for VSC8584 PHY
The VSC8584 PHY is a 4-port PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with the
MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set
the blinking pattern of each of its 4 LEDs, supports hardware offloading
of MACsec and supports SyncE as well as HP Auto-MDIX detection.

This adds support for 10/100/1000BASE-T and SGMII/QSGMII link with the
MAC.

The VSC8584 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.

The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.

The revA of the VSC8584 PHY (which is not and will not be publicly
released) should NOT patch the firmware of the microcontroller or it'll
make things worse, the easiest way is just to not support it.

Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:58 -06:00
Cédric Le Goater
1e5d8aaf4f aspeed: ast2500: fix D2-PLL clock setting in RGMII mode
The algorithm in the ast2500_calc_clock_config() routine suffers from
integer rounding and the requested rate does not get the appropriate
set of Numerator, Denumerator, Post Divider parameters.

This is the case for the D2-PLL clock used by the MAC controllers in
RGMII mode. The requested rated is 250MHz but a 251MHz is assigned.

The easiest way to fix this problem is to introduce an array of clock
settings defining the N, M, P parameters for well known frequencies
used by the Aspeed SoC.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:58 -06:00
Cédric Le Goater
e6ddacc2d0 net: ftgmac100: Add support for the Aspeed SoC
The Faraday ftgmac100 MAC controllers as found on the Aspeed SoCs have
some slight differences in the HW interface (End-Of-Rx/Tx-Ring bits).

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:58 -06:00
Cédric Le Goater
64ae823417 aspeed: ast2500: fix missing break in D2PLL clock enablement
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:57 -06:00
Cédric Le Goater
1c0c61e927 net: ftgmac100: add clock support
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:57 -06:00
Cédric Le Goater
d0e0b84c66 net: ftgmac100: handle timeouts when transmitting
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:57 -06:00
Cédric Le Goater
e766849713 net: ftgmac100: convert the RX/TX descriptor arrays
Use simple arrays under the device priv structure to hold the RX and
TX descriptors and handle memory coherency by invalidating or flushing
the d-cache when required.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:57 -06:00
Cédric Le Goater
538e75d3fc net: ftgmac100: add MDIO bus and phylib support
Implement the MDIO bus read/write functions using the readl_poll_timeout()
routine, initialize the bus and scan for the PHY. RGMII and RMII mode
are supported.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:57 -06:00
Cédric Le Goater
591ffd98b0 net: ftgmac100: use setbits_le32() in the reset method
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:56 -06:00
Cédric Le Goater
f95de0bd10 net: ftgmac100: convert to driver model
The driver is based on the previous one and the code is only adapted
to fit the driver model. The support for the Faraday ftgmac100
controller is the same with MAC and MDIO bus support for RGMII/RMII
modes.

Configuration is updated to enable compile again. At this stage, the
driver compiles but is not yet functional.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:56 -06:00
Cédric Le Goater
3bd796351f net: ftgmac100: use the aligned() macro
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:56 -06:00
Cédric Le Goater
f72b4a3dde net: ftgmac100: use the BIT() macro
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:56 -06:00
Stefan Roese
c895ef4650 net: Add MT7628 ethernet driver
This patch adds ethernet support for the MIPS based Mediatek MT76xx SoCs
(e.g. MT7628 and MT7688), including a minimum setup of the integrated
switch. This driver is loosly based on the driver version included in
this MediaTek github repository:

https://github.com/MediaTek-Labs/linkit-smart-uboot.git

Tested on the MT7688 LinkIt smart-gateway and on the
Gardena-smart-gateway.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Frank Wunderlich <frankwu@gmx.de>
Cc: Weijie Gao <hackpascal@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:56 -06:00
Tom Rini
5ef76e59c1 Merge branch 'master' of git://git.denx.de/u-boot-sh 2018-11-04 08:12:21 -05:00
Marek Vasut
a376dde1de mmc: tmio: sdhi: Merge DTCNTL access into single register write
It is perfectly fine to write th DTCNTL TAP count and enable the
SCC sampling clock operation in the same write.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-11-02 16:07:04 +01:00
Marek Vasut
2fc10754d1 mmc: tmio: sdhi: Implement waiting for DAT0 line state
When the bus switches to 1.8V mode of operation, it is necessary to
verify that the card correctly initiated and completed the voltage
switch. This is done by reading out the state of DATA0 line.

This patch implement support for reading out the state of the DATA0
line, so the MMC core code can correctly switch to 1.8V mode.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-11-02 16:04:45 +01:00
Marek Vasut
dc1488f1d2 mmc: tmio: sdhi: Clear HS400 settings when resetting SCC
Make sure to clear HS400 configuration when resetting the SCC block.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-11-02 16:04:45 +01:00
Marek Vasut
52e1796883 mmc: tmio: sdhi: Touch SCC only when UHS capable
Add check to avoid touching the SCC tuning registers in case the IP
doesn't support them or if the support isn't in place yet.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-11-02 16:04:44 +01:00
Marek Vasut
c83da2ebc0 mmc: tmio: Preinitialize regulator to 3.3V
Preinitialize the SD card signals regulator to 3.3V, which is the
default post-reset setting, to be sure the regulator is set to a
valid value.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-11-02 15:57:14 +01:00
Marek Vasut
8171f99e7d mmc: tmio: Configure clock before any other IOS
Configure the clock settings before reconfiguring any other IO settings.
This is required when the clock must be stopped before changing eg. the
pin configuration or any of the other properties of the bus. Running the
clock configuration first allows the MMC core to do just that.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-11-02 15:57:14 +01:00
Marek Vasut
33633ebb1c mmc: tmio: Silence transfer errors when tuning
In case the controller performs card tuning, that is, sends MMC
command 19 or 21, silence possible CRC error warning prints. The
warnings are bound to happen, since the tuning will fail for some
settings while searching for the optimal configuration of the bus
and that is perfectly OK.

This patch passes around the MMC command structure and adds check
into tmio_sd_check_error() to avoid printing CRC error warning
when the tuning happens.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-11-02 15:57:14 +01:00
Marek Vasut
b22c8d0de4 mmc: tmio: Improve error handling
Properly handle return values and abort operations when they are
non-zero. This is a minor improvement, which fixes two remaining
unchecked return values.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-11-02 15:57:14 +01:00
Marek Vasut
645a575aeb mmc: tmio: Simplify pinmux handling
The SD UHS SDR12, SDR25, SDR50, SDR104, DDR50 and MMC HS200, HS400
modes all use 1.8V signaling, while all the legacy modes use 3.3V
signaling. While there are extra modes which use 1.2V signaling,
the existing hardware does not support those.

Simplify the pinmux such that 3.3V signaling implies legacy mode
pinmux and the rest implies UHS mode pinmux. This prevents the
massive case statement from growing further. Moreover, it fixes
an edge case where during SD 1.8V switch, the bus mode is still
set to default while the signaling is already set to 1.8V, which
results in an attempt to communicate with a 1.8V card using pins
in 3.3V mode and thus communication failure.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-11-02 15:57:14 +01:00
Marek Vasut
5dbdd3a600 pinctrl: renesas: Add POCCTRL handling to r8a77990
Add definition of the POCCTRL register and bits therein to R8A77990 E3
pincontrol driver. This allows the pincontrol driver to configure SDHI
pin voltage according to power-source DT property.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-11-02 15:57:13 +01:00
Marek Vasut
0ff9e4800f pinctrl: renesas: Fix DRV register offset
Use fixed 4bit size for generating the DRV register element mask,
not the size of the value, which can be smaller.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-11-02 15:57:13 +01:00
Lokesh Vutla
26da01f700 power: spl: add SPL_DM_REGULATOR_GPIO in Kconfig
The Makefile already tests for SPL_DM_REGULATOR_GPIO, but Kconfig
does not provide it. This adds SPL_DM_REGULATOR_GPIO to Kconfig.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-11-01 10:02:43 -04:00
Martin Fuzzey
65b60897a7 w1: fix data abort if no one wire bus master present
When the "w1 bus" command is used with no bus master present
a data abort may occur.

This is because uclass_first_device() returns zero, but sets the output
struct udevice pointer to NULL in the no device found case.

Fix w1_get_bus() to account for this and return an error code
as is expected by the callers.

Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-11-01 10:02:10 -04:00
Martin Fuzzey
586d4b010e w1-eeprom: ds24xxx: fix data abort in ds24xxx_probe()
Data abort was occurring when using "w1 bus" with a DS24B33 present.

The abort occurred in the ds24xxx_probe() because the struct w1_device
pointer was NULL. This is because that structure  is allocated by
the parent device uclass (by .per_child_platdata_auto_alloc_size)
and thus the correct accessor is dev_get_parent_platdata() not
dev_get_platdata()

Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-11-01 10:02:10 -04:00
Tom Rini
fdaccfeb5e Merge branch 'master' of git://git.denx.de/u-boot-socfpga 2018-10-31 17:15:55 -04:00
Simon Goldschmidt
d5de3d4978 arm: socfpga: fpga: fix type of local variable
The 'status' variable in 'socfpga_load()' for both gen5 and arria10
is of type 'unsigned long' while it is always used as 'int' only.
Change it to 'int'.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-10-31 01:41:10 +01:00
Bin Meng
db148f2a69 powerpc: t1040: Correct RCW EC2 settings
Per T1040RM (Rev. 1, 08/2015), there are 2 issues with the RCW EC2
settings.

- The value of FSL_CORENET_RCWSR13_EC2_FM1_GPIO is wrong and should
  be 0x04000000 (value of 1 in RCW bit [420:421])
- Value of 2/3 are reserved in RCW bit [420:421], hence there is no
  macro FSL_CORENET_RCWSR13_EC2_FM1_DTSEC5_MII.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-10-29 13:19:43 -07:00
Chris Packham
4eaf7f525a fsl/usb: Workaround for USB erratum-A005275
Workaround makes FS as default mode on all affected socs.

Add support to check erratum-A005275 validity for an soc. This info is
required to determine whether a given soc is affected by this erratum.
Add quirk for this erratum "has_fsl_erratum_a005275" . This quirk is used
to enable workaround for the errata

Force FS mode as default by:
        - making EPS as FS
        - setting PFSC bit to disable HS chirping

This workaround can be disabled by mentioning "no_erratum_a005275" in
hwconfig string

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-10-29 13:13:05 -07:00
Tom Rini
2f07a9a6d1 Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2018-10-29 11:21:00 -04:00
Patrick Delaunay
22929e1266 drivers: cosmetic: Convert SPDX license tags to Linux Kernel style
Complete in the drivers directory the work started with
commit 83d290c56f ("SPDX: Convert all of our single
license tags to Linux Kernel style").

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-10-28 09:26:39 -04:00
Tom Rini
f749b61821 Merge branch 'master' of git://git.denx.de/u-boot-net 2018-10-25 20:30:05 -04:00
Tom Rini
cf033e04da Merged imx8 architecture, fix build for imx8 + warnings
-----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAlvRk0gPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3IuAL/0jfCqEIzKbPXIz81zJ+43ZNPsyu4LluUFsP
 2s5+yKN4zPnxDaHmVyxKynREqCNCcbfz7biStEPRzIjQYPBWUWrqz1yceqvOTqWQ
 eh51ItNeow28IlnVEr40e5cNL28KPsAdO8Tx6yNiXdPndPOgm3DuFlT+Xbnv2/+P
 X9GYBoCD7EQ3aUJBDUKcN/AFSAl8YCQ43FKhowM18/ExeURiKk8YDRXVFgTDDd4J
 HIlzUbyeIG24xfmxc0MsUMEufMjqQE7k/tMfFvQJiwLBLkzuO+1WmbPlWd7XHqco
 t68mheBcm8m2G/CZJoxCy8ymUi5PKDJBhw3qQz646h+JiXP1lg7Yw8hf4nREV56k
 v/bMiDU1exIflI9Qf8CibxRAYv3bjKJD6p/uua2CIvsLO4emLPbi7DHFBdaQq+WB
 r32O0Xc6LiRBIhr/qeL/5HmxFT2o4lo+O9ybo10uhK8RA1LTPlQ0UNMwmSPLl4zR
 7e5YwnRCcHV492+/Fn31LWXUUVVxVw==
 =kkpS
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20181025' of git://git.denx.de/u-boot-imx

Merged imx8 architecture, fix build for imx8 + warnings
2018-10-25 10:16:21 -04:00
Anatolij Gustschin
58ec4d3342 net: fec_mxc: add support for i.MX8X
Add compatible property and enable the FEC ipg clock when probing
on i.MX8X. Add specific function for reading FEC clock rate via
clock driver when configuring MII speed register. Allow FEC_MXC
selection for i.MX8.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:38 -05:00
Baruch Siach
18593fa80b net: mvpp2: increase PHY reset pulse
The default Linux PHY reset delay is 10ms. This is also the requirement
for Marvell 88E151x PHYs, which are likely to be used with this Ethernet
MAC.

Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2018-10-24 14:45:38 -05:00
Baruch Siach
fa14027d5c net: mvpp2: fix polarity of PHY reset signal
The dm_gpio_set_value() call sets the logical level of the GPIO signal.
That is, it takes the GPIO_ACTIVE_{LOW,HIGH} property into account. The
driver needs to assert the reset, and then deassert it. Not the other
way around.

Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2018-10-24 14:45:38 -05:00
Martin Fuzzey
0126c641e8 net: dm: fec: Obtain the transceiver type from the DT
The DT property "phy-mode" already provides the transceiver type.
Use it so that we do not have to also set CONFIG_FEC_XCV_TYPE

Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:37 -05:00
Martin Fuzzey
ad8c43cbca net: dm: fec: Support the phy-supply binding
Configure the phy regulator if defined by the "phy-supply" DT phandle.

Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:37 -05:00
Martin Fuzzey
331fcabe4f net: dm: fec: Fix phy-reset-duration clamping and defaults
The DT binding says:
- phy-reset-duration : Reset duration in milliseconds.  Should present
  only if property "phy-reset-gpios" is available.  Missing the property
  will have the duration be 1 millisecond.  Numbers greater than 1000 are
  invalid and 1 millisecond will be used instead.

However the current code:
 - clamps values greater than 1000ms to 1000ms rather than 1.
 - does not initialize the delay if the property does not exist
   (else clause mismatch)
 - returns an error if phy-reset-gpios is not defined

Fix all this and simplify by using dev_read_u32_default()

Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:37 -05:00
Martin Fuzzey
9b8b918884 net: dm: fec: Fix time unit error in phy-reset-duration
The DT binding says that phy-reset-duration is in ms, but the driver
currently uses udelay().

Switch to mdelay() to fix this.

Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:37 -05:00
Jeremy Gebben
30a2c8cca8 net: phy: aquantia: autodetect if firmware needs to be loaded
If the phy reports a valid firmware version and doesn't indicate
a fault, skip loading the firmware.  This allows the same image
to be used on boards that have firmware storage and those that do not.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:37 -05:00
Jeremy Gebben
4506423ad2 net: phy: aquantia: add firmware loading support
Aquantia phys have firmware that can be loaded automatically
from storage directly attached to the phy or via MDIO commands.
Add support for loading firmware from either a file or a
raw location on an MMC device.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:37 -05:00
Jeremy Gebben
1c6501088e configs: migrate CONFIG_PHY_AQUANTIA to Kconfig
The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G.

Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-24 14:45:36 -05:00
Priit Laes
3d99a0b33a sunxi: display: Mark sunxi_rgb2yuv_coef array as const
sunxi_rgb2yuv_coef is readonly and never modified.

Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-24 22:02:15 +05:30
Vasily Khoruzhick
c33ba7ec8b pwm: sunxi: choose best prescaler to improve PWM resolution
Choose best prescaler to improve PWM resolution. Without this change
driver chooses first prescaler that gives us period value within
range, but it could be not the best one.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-24 21:57:16 +05:30
Vasily Khoruzhick
ce138cb429 pwm: sunxi: use new prescaler when configuring PWM
Looks like old prescaler was used when configuring PWM, fix it.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-24 21:57:05 +05:30
Vasily Khoruzhick
a877d4b1ae pwm: sunxi: fix off-by-one that prevented PWM to use prescaler bypass
Fix off-by-one that prevented PWM driver to use prescaler bypass.
Without this change prescaler is always enabled.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-24 21:56:57 +05:30
Tom Rini
c95c666d01 Merge git://git.denx.de/u-boot-x86 2018-10-22 13:56:10 -04:00
Bernhard Messerklinger
4684fa8bdd serial: mxc: Add match string for i.mx6 quad/dual lite serial
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
2018-10-22 18:56:17 +02:00
Cédric Le Goater
e1a8dfde5a watchdog: aspeed: restore default value of reset_mask
This is required for the current Linux kernel to reboot. It should also
probably be fixed in Linux.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-10-22 09:18:49 -04:00
Bin Meng
ed5df0852f nand: atmel: Initialize pmecc smu with correct size
Currently in pmecc_get_sigma(), the code tries to clear the memory
pointed by smu with wrong size 'sizeof(int16_t) * ARRAY_SIZE(smu)'.
Since smu is actually a pointer, not an array, so ARRAY_SIZE(smu)
does not generate correct size to be cleared.

In fact, GCC 8.1.0 reports a warning against it:

error: division 'sizeof (int16_t * {aka short int *}) / sizeof (int16_t
{aka short int})' does not compute the number of array elements
[-Werror=sizeof-pointer-div]

Fix it by using the correct size.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-10-22 09:18:49 -04:00
Anatolij Gustschin
7677c0de14 i2c: imx_lpi2c: fix typo and register base address format
Output the register base address in hex notation.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2018-10-22 14:35:57 +02:00
Xiaoliang Yang
517066a709 Kconfig: Convert CONFIG_IMX_WATCHDOG to Kconfig
Move this option to Kconfig and tidy up the config file of eight
boards which use it.

Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
2018-10-22 14:33:54 +02:00
Peng Fan
3cb1450380 mmc: fsl_esdhc: add uclass clk support
When CONIFG_CLK is enabled, use uclass clk api to handle
the clock.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
2018-10-22 13:00:09 +02:00
Ye Li
d423c93b66 fsl_esdhc: Update usdhc driver to support i.MX8
Add CONFIG_ARCH_IMX8 to use the 64bits support in usdhc driver.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
2018-10-22 13:00:09 +02:00
Peng Fan
8f5b6299bc serial: lpuart: support uclass clk api
Modify most APIs to use udevice as the first parameter, then
it will be easy to get the clk reference by using udevice pointer.
Use uclass api to get lpuart clk when CONFIG_CLK is enabled.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2018-10-22 12:59:02 +02:00
Ye Li
cdc16f6182 serial: lpuart: Enable RX and TX FIFO
Enable the RX and TX FIFO in LPUART driver to avoid the input lost
during U-Boot boot up.

Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2018-10-22 12:59:02 +02:00
Peng Fan
126f884903 serial_lpuart: Update lpuart driver to support i.MX8
Add i.MX8 compatible string and cpu type support to lpuart driver,
to use little endian 32 bits configurations.

Also, according to RM, the Receive FIFO Enable (RXFE) field in LPUART
FIFO register is bit 3, so this definition should change to 0x08
(not 0x40) for i.MX8, otherwise the Receive FIFO is not disabled.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2018-10-22 12:59:02 +02:00
Peng Fan
f77d441091 clk: imx: add clk driver for i.MX8QXP
Add clk driver for i.MX8QXP. This basic version supports clk
enable/disable/get_rate/set_rate operations for I2C, ENET,
SDHC0 and UART clocks.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2018-10-22 12:59:01 +02:00
Peng Fan
d526f340f7 power: Add power domain driver for i.MX8
Add the power domain DM driver for i.MX8, that it depends on the DTB
power domain trees to generate the power domain provider devices. Users
need to add power domain trees with property "compatible = "nxp,imx8-pd";"

When power on a PD device, the driver will power on its ancestor PD
devices in power domain tree.

When power off a PD device, the driver will check its child PD devices
first. Only if all child PD devices are off, then power off the current PD
device. Then the driver checks sibling PD devices. If sibling PD devices
are off, then it will power off parent PD device.

There is no counter maintained in this driver, but a state to hold current
on/off state. So the request and free functions are empty.

The power domain implementation in i.MX8 DTB set the "#power-domain-cells"
to 0, so there is no ID binding with each PD device. We don't use "id"
variable in struct power_domain. At the same time, we have to set of_xlate
to empty to bypass standard of_xlate in uclass driver.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2018-10-22 12:59:01 +02:00
Peng Fan
38b6686f05 pinctrl: Add pinctrl driver for i.MX8
Add pinctrl driver for i.MX8. The pads configuration is controlled
by SCU, so need to ask SCU to configure pads through scfw API.
Add pinctrl-scu to invoke sc_pad_set to configure pads.
Add a new flag IMX8_USE_SCU to differentiate i.MX8 from other platforms
which could directly configure pads from Acore side.
Add CONFIG_PINCTRL_IMX8 as the built gate.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2018-10-22 12:59:01 +02:00
Peng Fan
8b2a31f133 gpio: mxc_gpio: add support for i.MX8
Add i.MX8 support, there are 8 GPIO banks.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2018-10-22 12:59:01 +02:00
Peng Fan
ad9d40acb4 misc: imx8: add scfw api impementation
Add clk/misc/pad/pm/rm scfw api implementaion for different
drivers to invoke. The low level code is using misc_call
to invoke imx8_scu driver.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2018-10-22 12:59:01 +02:00
Peng Fan
ef64e782ec misc: add i.MX8 misc driver
Add i.MX8 MISC driver to handle the communication between
A35 Core and SCU.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2018-10-22 12:59:01 +02:00
Bin Meng
6ce383640c x86: tsc: Introduce config option for early timer frequency
So far the TSC timer driver supports trying hardware calibration first
and using device tree as last resort for its running frequency as the
normal timer.

However when it is used as the early timer, it only supports hardware
calibration and if it fails, the driver just panics. This introduces
a new config option to specify the early timer frequency in MHz and
it should be equal to the value described in the device tree.

Without this patch, the travis-ci testing on QEMU x86_64 target fails
each time after it finishes the 'bootefi selftest' as the test.py see
an error was emitted on the console like this:

  TSC frequency is ZERO
  resetting ...
  ### ERROR ### Please RESET the board ###

It's strange that this error is consistently seen on the travis-ci
machine, but only occasionally seen on my local machine (maybe 1 out
of 10). Since QEMU x86_64 target enables BOOTSTAGE support which uses
early timer, with this fix it should work without any failure.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-10-22 17:51:45 +08:00
Simon Glass
97d20f69f5 Enable CONFIG_TIMER_EARLY with bootstage
In initr_bootstage() we call bootstage_mark_name() which ends up calling
timer_get_us(). This call happens before initr_dm(), which inits driver
model.

On x86 we set gd->timer to NULL in the transition from board_init_f()
to board_init_r(). See board_init_f_r() for this assignment. So U-Boot
knows there is no timer available in the period immediately after
relocation.

On x86 the timer_get_us() call is implemented as calls to get_ticks() and
get_tbclk(). Both of these call dm_timer_init() to set up the timer, if
gd->timer is NULL and the early timer is not available.

However dm_timer_init() cannot succeed before initr_dm() is called.

So it seems that on x86 if we want to use CONFIG_BOOTSTAGE we must enable
CONFIG_TIMER_EARLY. Update the Kconfig to handle this.

Note: On most architectures we can rely on the pre-relocation memory still
being available, so that gd->timer pointers to a valid timer device and
everything works correctly. Admittedly this is not strictly correct since
the timer device is set up by pre-relocation U-Boot, but normally this is
fine. On x86 the 'CAR' (cache-as-RAM) memory used by pre-relocation U-Boot
disappears in board_init_f_r() and any attempt to access it will hang.
This is the reason why we must mark the timer as invalid when we get to
board_init_f_r().

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-10-22 17:51:45 +08:00
Marek Vasut
02e4d38d87 pci: Support parsing PCI controller DT subnodes
The PCI controller can have DT subnodes describing extra properties
of particular PCI devices, ie. a PHY attached to an EHCI controller
on a PCI bus. This patch parses those DT subnodes and assigns a node
to the PCI device instance, so that the driver can extract details
from that node and ie. configure the PHY using the PHY subsystem.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-10-20 15:23:38 -04:00
Adam Ford
2fe88d4522 Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig
This converts the following to Kconfig:
   CONFIG_FLASH_CFI_DRIVER
   CONFIG_SYS_FLASH_USE_BUFFER_WRITE
   CONFIG_FLASH_CFI_MTD
   CONFIG_SYS_FLASH_PROTECTION
   CONFIG_SYS_FLASH_CFI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-19 19:19:50 -04:00
Marek Vasut
758694ff07 bootcount: Make bootcount magic configurable
Add new Kconfig option, SYS_BOOTCOUNT_MAGIC, to select the boot
counter magic word. This can be useful ie. in case the entire
boot counter register is not usable.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
2018-10-19 14:16:43 -04:00
Tom Rini
d0423c44f1 Merge git://git.denx.de/u-boot-microblaze
Xilinx changes for v2018.11-rc2-v2

FPGA:
- Fix SPL fpga loading from FIT

ARM64:
- Fix gic accesses in EL2/EL1

Xilinx:
- Add dlc20 board support
- Add Versal board support
- Sync defconfigs
- Enable MP via Kconfig
- Add missing efuse node
- Enable CDC for zcu100

cmd:
- Fix kgdb Kconfig dependency
2018-10-16 13:57:23 -04:00
Michal Simek
3dc80934f4 net: gem: Do not setup any clock for Xilinx SoC Versal
Xilinx SoC Versal is using fixed clock where setting rate is not supported.
That's why workaround the driver till real clock driver is supported.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-10-16 16:53:24 +02:00
Michal Simek
ec48b6c991 arm64: versal: Add support for new Xilinx Versal ACAPs
Xilinx is introducing Versal, an adaptive compute acceleration platform
(ACAP), built on 7nm FinFET process technology. Versal ACAPs combine
Scalar Processing Engines, Adaptable Hardware Engines, and Intelligent
Engines with leading-edge memory and interfacing technologies to deliver
powerful heterogeneous acceleration for any application. The Versal AI
Core series has five devices, offering 128 to 400 AI Engines. The series
includes dual-core Arm Cortex™-A72 application processors, dual-core Arm
Cortex-R5 real-time processors, 256KB of on-chip memory with ECC, more
than 1,900 DSP engines optimized for high-precision floating point with
low latency.

The patch is adding necessary infrastructure in place without enabling
platform which is done in separate patch.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-10-16 16:53:21 +02:00
Tom Rini
2364b70c87 Merge branch 'master' of git://git.denx.de/u-boot-i2c 2018-10-16 07:25:28 -04:00
Tom Rini
e6cd05e502 Merge branch 'master' of git://git.denx.de/u-boot-spi 2018-10-12 11:54:13 -04:00
Tom Rini
15f22ac2ee ldpaa_eth.c: Fix warning when PHYLIB is not enabled
We need to #ifdef some variables to avoid warning about them being
unused.

Fixes: 1a048cd656 ("driver: net: fsl-mc: Add support of multiple phys for dpmac")
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-12 07:41:24 -04:00
Ashish Kumar
5c391486b4 sf: Add MICRON manufacturer id
NOR flash name MT35X_QLKA and MT25Q_** used on NXP board has
manufacturer id as 0x2C, which are rather for newer flashes
after the split of Micron from ST.

So macro for this micron manufacturer id.

Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
[jagan: updated commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-10-12 11:37:49 +05:30
Heiko Schocher
e3bc4bb861 i2c: fix: Add support for the Arm's Versatile Express I2C controller
accidentially while fixing merge errors for patch:
https://lists.denx.de/pipermail/u-boot/2018-September/342278.html

missed to add files:

MAINTAINERS
drivers/i2c/Kconfig
drivers/i2c/Makefile

add them with this patch.

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Liviu Dudau <liviu.dudau@foss.arm.com>
2018-10-12 07:25:39 +02:00
Tom Rini
0223462b37 Merge branch 'master' of git://git.denx.de/u-boot-net 2018-10-11 15:28:32 -04:00
Pankaj Bansal
1a048cd656 driver: net: fsl-mc: Add support of multiple phys for dpmac
Till now we have had cases where we had one phy device per dpmac.
Now, with the upcoming products (LX2160AQDS), we have cases, where there
are sometimes two phy devices for one dpmac. One phy for TX lanes and
one phy for RX lanes. to handle such cases, add the support for multiple
phys in ethernet driver. The ethernet link is up if all the phy devices
connected to one dpmac report link up. also the link capabilities are
limited by the weakest phy device.

i.e. say if there are two phys for one dpmac. one operates at 10G without
autoneg and other operate at 1G with autoneg. Then the ethernet interface
will operate at 1G without autoneg.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-10 12:45:28 -05:00
Pankaj Bansal
1ed19a1421 driver: net: fsl-mc: initialize dpmac irrespective of phy
The dpmac initalization should not depend on phy.
As the phy is not necessary to be present for dpmac to function.
Therefore, remove dpmac initialization dependency from phy.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-10 12:45:23 -05:00
Pankaj Bansal
a3cb5340f1 driver: net: fsl-mc: Modify the dpmac link detection method
when there is no phy present for a dpmac, a dummy phy device is created.
when we move to multiple phy method, we need to create as many dummy phy
devices.

Change this method so that we don't need to create dummy phy devices.
We always report linkup if no phy is present.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-10 12:45:01 -05:00
Pankaj Bansal
f259c43d89 driver: net: fsl-mc: fix error handing in init_phy
if an error occurs during init_phy, we should free the phydev structure
which has been allocated by phy_connect.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-10 12:43:18 -05:00
Pankaj Bansal
d75e81d9e0 driver: net: fsl-mc: remove unused strcture elements
The phydev structure is present in both ldpaa_eth_priv and
wriop_dpmac_info. the phydev in wriop_dpmac_info is not being used

As the phydev is created based on phy_addr and bus members of
wriop_dpmac_info, it is appropriate to keep phydev in wriop_dpmac_info.

Also phy_regs is not being used, therefore remove it

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-10 12:36:34 -05:00
Tom Rini
3d5ced9e22 Test improvements to tidy up output and drop duplicate tests
Sandbox SPL/TPL support
 Various dm-related improvements
 -----BEGIN PGP SIGNATURE-----
 
 iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlu9RL4RHHNqZ0BjaHJv
 bWl1bS5vcmcACgkQfxc6PpAIreYd8gf+NYAGhpiEZZ5vc3DB4Xdn2okgakbbg0QQ
 /b0Lr9xQsKgZthK0rvPlH2dXxf+ViAm1iHTy8KBCFi0SHNder48Zui9uTrX0NRq8
 pLZGyJPXPYbiyc4pQTEJpTth4iShcphRVio0no4sLpNQqO4aQrialSLa9fnwd9Ra
 1l9mF91aaYw6cG+/ejg3UR1LfsDdQ5bjubt0Fw0wGX9UvQOAz5gz5+a17wrz6+Gx
 L0gzvyfbuLUhbWB36DXikrL14DAFys2uV9aHJ5zEd53l+F7ZHWsupCO0OtN66cV7
 KpPKoYG7vhLqBXKpyrW20T+BPeSyDKmDQE6wbpECmEDOvKzvW67O/w==
 =Bfjm
 -----END PGP SIGNATURE-----

Merge tag 'dm-9oct18' of git://git.denx.de/u-boot-dm

Test improvements to tidy up output and drop duplicate tests
Sandbox SPL/TPL support
Various dm-related improvements
2018-10-10 13:35:17 -04:00
Tom Rini
98068b3be5 Merge branch 'master' of git://git.denx.de/u-boot-sh 2018-10-10 13:35:14 -04:00
Keerthy
0f3cf2b3e5 gpio: da8xx: Push generic defines of gpio.h out of mach-davinci
Push generic defines of gpio.h out of mach-davinci to drivers/gpio
now that non-davinci architectures are beginning to use this IP.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix calimain build]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-10 13:35:03 -04:00
Keerthy
401d74cb2c gpio: da8xx: Add k2g compatible
Add k2g compatible so that k3 SoCs can be supported

Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-10-10 13:32:41 -04:00
Pankaj Bansal
afd6c6b470 driver: net: fsl-mc: modify the label name
The goto label name is misspelled it should be DPMAC not DPAMC

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-10 12:30:28 -05:00
Joe Hershberger
72ff004258 test: eth: Add a test for the target being pinged
The target will respond to pings while doing other network handling.
Make sure that the response happens and is correct.

This currently corrupts the ongoing operation of the device if it
happens to be awaiting an ARP reply of its own to whatever serverip it
is attempting to communicate with. In the test, add an expectation that
the user operation (ping, in this case) will fail. A later patch will
address this problem.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-10-10 12:29:00 -05:00
Joe Hershberger
45988dae4c test: eth: Add a test for ARP requests
This tests that ARP requests made to this target's IP address are
responded-to by the target when it is doing other networking operations.

This currently corrupts the ongoing operation of the device if it
happens to be awaiting an ARP reply of its own to whatever serverip it
is attempting to communicate with. In the test, add an expectation that
the user operation (ping, in this case) will fail. A later patch will
address this problem.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-10-10 12:29:00 -05:00
Joe Hershberger
9cbe5972c3 net: sandbox: Add a priv ptr for tests to use
Tests need to be able to pass their "unit test state" to the handlers
where asserts are evaluated. Add a function that allows the tests to set
this private data on the sandbox eth device.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-10-10 12:28:59 -05:00
Joe Hershberger
c67a420781 net: sandbox: Allow fake eth to handle more than 1 packet response
Use up to the max allocated receive buffers so as to be able to test
more complex situations.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-10-10 12:28:58 -05:00
Joe Hershberger
76a503439e net: sandbox: Share the priv structure with tests
If tests want to implement tx handlers, they will likely need access to
the details in the priv structure.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-10-10 12:28:57 -05:00
Joe Hershberger
c7eb733d60 net: sandbox: Make the fake eth driver response configurable
Make the send handler registerable so tests can check for different
things.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-10-10 12:28:57 -05:00
Joe Hershberger
e95bb16110 net: sandbox: Refactor sandbox send function
Make the behavior of the send function reusable.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-10-10 12:28:56 -05:00
Joe Hershberger
e4ab9a6508 net: sandbox: Move disabled flag into priv struct
Store the per-device data with the device.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-10-10 12:28:56 -05:00
Janine Hagemann
0f347a0096 net: phy: ti: Add binding for the CLK_OUT pin muxing
The DP83867 has a muxing option for the CLK_OUT pin. It is possible
to set CLK_OUT for different channels.
Create a binding to select a specific clock for CLK_OUT pin.

Based on commit 9708fb630d19 ("net: phy: dp83867: Add binding for
the CLK_OUT pin muxing option") of mainline linux kernel.

Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-10 12:28:54 -05:00
Janine Hagemann
be71a74c59 net: phy: ti: Recover from "port mirroring" N/A MODE4
The DP83867 when not properly bootstrapped - especially with LED_0 pin -
can enter N/A MODE4 for "port mirroring" feature.

To provide normal operation of the PHY, one needs not only to explicitly
disable the port mirroring feature, but as well stop some IC internal
testing (which disables RGMII communication).

To do that the STRAP_STS1 (0x006E) register must be read and RESERVED bit
11 examined. When it is set, the another RESERVED bit (11) at PHYCR
(0x0010) register must be clear to disable testing mode and enable RGMII
communication.

Thorough explanation of the problem can be found at following e2e thread:
"DP83867IR: Problem with RESERVED bits in PHY Control Register (PHYCR) -
Linux driver"

https://e2e.ti.com/support/interface/ethernet/f/903/p/571313/2096954#2096954

Based on commit ac6e058b75be ("net: phy: dp83867: Recover from "port mirroring"
N/A MODE4") of mainline linux kernel.

Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
2018-10-10 12:28:54 -05:00
Janine Hagemann
fba725f410 net: phy: ti: Add lane swapping support in the DP83867 TI's PHY driver
This patch adds support for enabling or disabling the lane swapping
(called "port mirroring" in PHY's CFG4 register) feature of the DP83867
TI's PHY device.

One use case is when bootstrap configuration enables this feature (because
of e.g. LED_0 wrong wiring) so then one needs to disable it in software
(at u-boot/Linux).

Based on commit fc6d39c39581 ("net: phy: dp83867: Add lane swapping
support in the DP83867 TI's PHY driver") of mainline linux kernel.

Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-10 12:28:53 -05:00
Bin Meng
dda5251037 net.h: Include linux/if_ether.h to avoid duplication
There are plenty of existing drivers that have macros like ETH_ALEN
defined in their own source files. Now that we imported the kernel's
if_ether.h to U-Boot we can reduce some duplication.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-10 12:28:52 -05:00
Jagan Teki
ba3c22bf18 spi: davinci: Add platdata support
Davanci spi driver has DM support already, this patch
add support for platdata so-that SPL can use it for
low foot-print.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Adam Ford <aford173@gmail.com>
2018-10-10 11:35:06 +05:30
Adam Ford
c8602061a7 mtd: uboot: Fix hanging during mtd list command
Some boards (like omap3_logic) hang when trying to access
address 0. This happens when executing the new 'mtd list' command.
This patch enhances the checks for conditions that would
preclude mtd_probe_devices() from operating.

Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-10-10 11:34:10 +05:30
Bin Meng
339613eba5 net: pch_gbe: Make probe/remove static
These two routines are internal to pch_gbe driver.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-09 14:18:21 -05:00
Bin Meng
b06d76f9ae linux/compat.h: Add netdev_### log macros
Currently there are two ethernet drivers (mvneta.c and mvpp2.c) that
has netdev_### (eg: netdev_dbg) log macros defined in its own driver
file. This adds these log macros in a common place linux/compat.h.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-09 14:18:17 -05:00
Marek Vasut
beced53a74 mmc: tmio: Limit DMA to 32bit on R-Car Gen3
The internal DMAC on Gen3 is 32bit only, limit the DMA address
range to 32bit.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-10-09 17:21:44 +02:00
Marek Vasut
92bde154ec mmc: tmio: Pass full address to tmio_sd_addr_is_dmaable()
Pass the entire source data pointer to tmio_sd_addr_is_dmaable()
so we don't have to apply casts throughout the code.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-10-09 17:21:43 +02:00
Simon Glass
9949ee876d video: at91: Adjust vidconsole_position_cursor() to use char pos
At present this function uses pixels but it seems more useful for it to
position in terms of characters on the screen. This also matches the
comment to the function. Update this.

Unfortunately there is one user of this function (at91). Have a crack at
fixing this, since I cannot test it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
2018-10-09 04:40:27 -06:00
Simon Glass
751fed426f sysreset: Add a way to find the last reset
We have a method to return the last reset as a string for humans, but not
a method that allows it to be used programmatically. Add a new method that
returns the last reset as an enum.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
eb517315a6 sysreset: Tidy up a few comments and logging
Some comments are incorrect or missing pieces. Fix these and use logging
to print the error.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
595aac9824 pci: Add a little more debugging to pci_rom
Add some logging on failure.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-10-09 04:40:27 -06:00
Simon Glass
07bc873c73 ctags: Minor changes to fix ctags output
At present ctags emits lines with unmatched quotes which means that the
output file is invalid. This is with exuberant-ctags version 5.9~svn201103
but I also see it with plain ctags. I am not sure that it is a bug though.

Make a few minor changes in the source code to fix this problem.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
a4f737a9c3 panel: Expand the backlight support
At present the panel can be turned on but not off, and the brightness
cannot be controlled at run-time. Add a new API function to both the panel
and backlight uclasses to handle this. Enhance the PWM backlight driver
to deal with custom levels properly and allow the backlight to be turned
on and off.

Update the test to cover thes new features.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
5d9a88f44a test: panel: Add a test for the panel uclass
At present this uclass has no tests. Add a simple one which checks the PWM
configuration, regulator and GPIO.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
d07b6e145e cros_ec: Add support for v3 messages on LPC
At present version 3 messages are only supported on SPI. Add support for
using LPC as well, as used on samus.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
a12ef7e26a cros_ec: Update cros_ec_read_hash() to specify the image
Allow selection of which EC image to hash.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
6f1c0430e8 cros: Update ec_commands to latest version
This file has changed quite a bit in the last 5 years as the capabilities
of the ECs have grown. Sync it up with the copy in coreboot commit
b9141f2215.

The only change is the addition of EC_VBNV_BLOCK_SIZE_V2. This is needed
because U-Boot uses the new v2 vboot API and this is not currently fully
supported by Chromium OS firmware.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
c89d32a7b1 tpm: Use livetree and allow children
Adjust the TPM drivers to use livetree (only one does not). Also,
sometimes TPMs can have child devices if they provide a service to the
system (such as storing secure data), so permit that.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
c6ebd011bb video: Adjust video_clear() to return an error
All driver-model operation should return an error code. Adjust this
function to do so also.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
2018-10-09 04:40:27 -06:00
Simon Glass
5e24a2ef8b dm: spi: Add logging of some return values
When SPI flash operations fail it is helpful to be able to see the error
codes and where they are generated. Add logging to capture this
information for read operations.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
6322a7b63f cros: Update cros_ec code to use struct udevice
At present we pass around a private pointer to specify the cros_ec device.
With driver model it makes more sense to pass the device. Update the code
to do this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
aa0ffe8eb9 serial: Allow serial to be absent in TPL
At present this option applies to SPL, but it should be available in TPL
also, and separately. Change to using CONFIG_IS_ENABLED(), add a new
Kconfig option and fix up hang().

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
6307896c17 tpm: Add support for SPL and TPL
At present the tpm can only be used in U-Boot proper. Updated it to work
in SPL and TPL also.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
06f94461a9 fdt: Allow indicating a node is for U-Boot proper only
At present it is not possible to specify that a node should be used before
relocation (in U-Boot proper) without it also ending up in SPL and TPL
device trees. Add a new "u-boot,dm-pre-proper" boolean property for this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
380d4f787a rtc: Allow use of RTC in SPL and TPL
Add Kconfig options so that the RTC can be used in SPL and TPL. This is
helpful for accessing the contents of CMOS RAM, for example.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
107610775b Kconfig: Convert CONFIG_RTC_MC146818 to Kconfig
Move this option to Kconfig and tidy up the two boards which use it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
ef39151583 blk: Support block drivers in TPL
At present it is not possible to enable/disable block drivers in TPL. This
is needed to provide sandbox support. Add a Kconfig option and adjust the
Makefile.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
985ca3945f spl: input: Allow input in SPL and TPL
In some cases it is necessary to read the keyboard in early phases of
U-Boot. Update the config to allow this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
97f57109bb sf: Avoid allocating memory on every read operation
At present spi_flash_cmd_read_ops() allocates and frees a few bytes of
memory every time it is called. It is faster to use the stack for this
and this is now supported by the minimum GCC version required by U-Boot.

Remove the allocation and use a variable-sized array instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
e6c5c94a79 dm: core: Update ofnode to read binman-style flash entry
At present ofnode_read_fmap_entry() reads a flash map entry in a format
which is not supported by binman. To allow use to use binman-format
descriptions, update this function.

Also add a simple test.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
cdb6aa0afb dm: core: Add a function to find the first inactive child
Some devices have children and want to press an existing inactive child
into service when needed. Add a function to help with this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
9f15cc14bf dm: core: Update some functions to use const
Quite a few functions do not actually modify the device that is passed in.
Update the function signatures to reflect that.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
c7a3accc3f dm: core: Alloc uclass-private data to be cache-aligned
There is no reason why this feature should not be supported for uclass-
private data. Update the code accordingly.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
4af3e9ad8a sandbox: Restore blocking I/O on exit
At present sandbox sets non-blocking I/O as soon as any input is read
from the terminal. However it does not restore the previous state on
exit. Fix this and drop the old os_read_no_block() function.

This means that we always enable blocking I/O in sandbox (if input is a
terminal) whereas previously it would only happen on the first call to
tstc() or getc(). However, the difference is likely not important.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
66613f5dd2 dm: spi: Clean up detection of sandbox SPI emulator
Now that we don't have to deal with the command-line flag we can simplify
the code for detecting the emulator. Remove the lookup based on the SPI
specification, relying just on the device tree to locate the emulator.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
ef8a25006d sandbox: tpm: Enhance to support the latest Chromium OS
This driver was originally written against Chromium OS circa 2012. A few
new features have been added. Enhance the TPM driver to match. This mostly
includes a few new messages and properly modelling whether a particular
'space' is present or not.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
998af31903 sandbox: tpm: Tidy up enums and return values
Use an enum for command values instead of open-coding them. This removes
the need for comments. Also make sure the driver returns proper error
numbers instead of -1.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
114b60a7e6 serial: sandbox: Allow serial output without device tree
At present sandbox assumes that device-tree control is active, but this
may not be the case in SPL or TPL. Add some conditions to handle this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
ee4417644c sandbox: Add a debug UART
Add support for the debug UART so that sandbox provides build testing for
this feature.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
55d39911c0 sandbox: video: Speed up video output
At present there are many situations where sandbox syncs the display to
the SDL frame buffer. This is a very expensive operation but is only
needed every now and then. Update video_sync() so that we can specify
whether this operation is really needed.

At present this flag is not used on other architectures. It could also
be used for reducing writeback-cache flushes but the benefit of that would
need to be investigated.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
2018-10-09 04:40:27 -06:00
Simon Glass
c3aed5db59 sandbox: spi: Add more logging
Add logging to aid debugging features in these drivers. Also drop some
code in sandbox_spi_xfer() which is not used.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
1289e96797 sandbox: spi: Drop command-line SPI option
At present we support specifying SPI flash devices to use in the device
tree and on the command line. Drop the second option, since it is a pain
to support nicely with driver model, and unnecessary.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:26 -06:00
Trent Piepho
4a094725b4 rtc: Add read8 and write8 support to isl1208 driver
This can be used for device register access from board code.

This allows access to capabilities in the RTC chip not abstracted in
U-Boot's RTC class.  E.g., device NVRAM or a tamper detection circuit.

Cc: Klaus Goger <klaus.goger@theobroma-systems.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-10-08 14:45:02 -04:00
Marek Vasut
a6a45cd325 ofnode: Add missing address translation into ofnode_get_addr_size()
Of CONFIG_OF_TRANSLATE is enabled, this function still returns
untranslated bogus results. Add the missing translation.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-10-08 07:34:34 -06:00
Marek Vasut
51cb927504 ofnode: Replace of_n_addr_cells with of_n_size_cells
The size should be decoded using of_n_size_cells(), make it so.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-10-08 07:34:34 -06:00
Jens Wiklander
0a60a81ba3 Kconfig: sandbox: enable cmd_avb and dependencies
Enables cmd_avb and its dependencies need to run the AVB tests.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
[trini: Disable for sandbox_noblk]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-07 13:34:19 -04:00