Enable driver model for SPI and SPI_FLASH to remove the following
compile warning on CM-FX6 SOM:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
====================================================
This change introduced SPL build error as shown:
In file included from include/common.h:47:0,
from drivers/mtd/spi/sf_probe.c:10:
drivers/mtd/spi/sf_probe.c: In function 'spi_flash_std_probe':
drivers/mtd/spi/sf_probe.c:149:54: error: dereferencing pointer to incomplete type 'struct dm_spi_slave_platdata'
scripts/Makefile.build:278: recipe for target 'spl/drivers/mtd/spi/sf_probe.o' failed
make[3]: *** [spl/drivers/mtd/spi/sf_probe.o] Error 1
scripts/Makefile.build:432: recipe for target 'spl/drivers/mtd/spi' failed
make[2]: *** [spl/drivers/mtd/spi] Error 2
Disabling DM for SPI support(SPI and SF) in SPL resolves the issue.
Target was compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
The SPL does not have DM enabled and therefor still needs to use the
hardware watchdog interface provided by the imx-watchdog driver.
Fixes: broken reset command after f2929d11a6 ("watchdog: imx: Use
immediate reset bits for expire_now")
Signed-off-by: Claudius Heine <ch@denx.de>
Make first step in DT/DM migration. Enable OF_CONTROL only for the main
U-Boot image for now.
Remove mmc_init_main() because board_mmc_init() is not called when
DM_MMC is enabled.
DM_MMC requires DM_GPIO for card-detect to work. That in turn makes gpio
request mandatory. Add code to request/free gpios in platform code.
MMC devices are now numbered according to DT. The SD card is 1, and eMMC
is 2. Account for that in board_mmc_get_env_dev(), BOOT_TARGET_DEVICES,
and has_emmc().
DM_MMC requires BLK. However, the (BLK && !DM_USB) combination disables
USB_STORAGE. Enable DM_USB to preserve USB functionality. Add also
DM_REGULATORS for the USB power controller. This allows us to drop
board_ehci_hcd_init() and setup_usb().
Runtime selection of DT is necessary because of the i.MX6QD vs i.MX6SDL
incompatibility. DT selection does not rely on GPIOs, since DM_GPIO
depends on DT. Instead, we take one "fully featured" DT of each variant.
That should be enough to boot from both SD card and eMMC.
Since we don't select the exact DT, override the generic
show_board_info() that shows the selected DT 'model' field.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Import fsl-imx-audmux.h from Linux as of v5.4-rc6. The header is
unchanged since v4.18.
That would make it easier to import DT files that depend on imx-audmux
definitions from the kernel tree.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Pass rtc_status via the device tree, instead of on kernel command line.
Additionally, the 2038 mitigation is reported, if applied successfully.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
DM for PCI pulls DM for ethernet that also needs other changes described
below to build u-boot and keep existing functionality - ability to update
MAC addresses of FEC ethernet adapter and I210 adapter connected to the
Marvell switch.
- fec_mxc driver with DM needs PHYLIB;
- configuration items are moved from ge_bx50v3.h to ge_bx50v3_defconfig;
- FEC is marked as eth0 because it is always present, so indices changed:
I210 are still probed in the same order;
- board_eth_init() was used by legacy ethernet, setup for enet iomux and
pcie is moved to the board_late_init();
- pci_init() is called from the board_late_init() to initiate PCI bus
probing, so I210 devices are propagated to the device tree;
Signed-off-by: Denis Zalevskiy <denis.zalevskiy@ge.com>
[Describe PHY reset in device tree]
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Use vidconsole for output to the LCD, now that DM_VIDEO is used. Write
white text on a black background, like before migrating to DM_VIDEO.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
This patch introduces support for i.MX28 based XEA board.
This board supports DM/DTS in U-Boot proper as well as DM aware drivers
in SPL (u-boot.sb) by using OF_PLATDATA.
More detailed information regarding usage of it can be found in
./board/liebherr/xea/README file.
U-Boot SPL 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
Trying to boot from MMC1
MMC0: Command 8 timeout (status 0xf0344020)
mmc_load_image_raw_sector: mmc block read error
U-Boot 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: SSP SPI #3, master, 3V3 NOR
Model: Liebherr (LWE) XEA i.MX28 Board
DRAM: 128 MiB
MMC: MXS MMC: 0
Loading Environment from SPI Flash... SF: Detected n25q128a13 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@800f0000 (eth0) using random MAC address - ce:e1:9e:46:f3:a2
eth0: ethernet@800f0000
Hit any key to stop autoboot: 0
Signed-off-by: Lukasz Majewski <lukma@denx.de>
sync defaut Envoronment with customer changes.
Unfortunately they are not changeable, as already
board is in production mode.
Get rid of the big bootcommand and set bootcommand
through Kconfig option.
Signed-off-by: Heiko Schocher <hs@denx.de>
add DM_VIDEO support and remove now unneeded board
code. As we show a bmp logo on boot, call now
bmp_display() from board code and do not use
cfb_console anymore.
Signed-off-by: Heiko Schocher <hs@denx.de>
enable CONFIG_DM_SPI and CONFIG_DM_SPI_FLASH
and get rid of build removal warnings.
define CONFIG_GPIO_ENABLE_SPI_FLASH is not longer
needed, so remove it from config_whitelist.txt
Signed-off-by: Heiko Schocher <hs@denx.de>
remove aristainetos-v2.c file, as we now want to
switch to DM/DTS support and have all board specific
code in one file. Goal is to setup differences
through DT.
Signed-off-by: Heiko Schocher <hs@denx.de>
remove 2b version of aristainetos board, as it
is easier to make the DM / DTS port and introduce
the 2b board version again (also some more board
version).
Signed-off-by: Heiko Schocher <hs@denx.de>
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
The build failure was originally reported on arm64-musl
target at https://bugs.gentoo.org/703132. Here is the amd64-musl
variant:
```
$ LANG=C make CROSS_COMPILE=x86_64-gentoo-linux-musl- tools-only_defconfig -j$(nproc)
$ LANG=C make CROSS_COMPILE=x86_64-gentoo-linux-musl- tools-all -j$(nproc)
...
include/u-boot/crc.h:37:44: error: unknown type name 'uint'; did you mean 'int'?
37 | void crc16_ccitt_wd_buf(const uint8_t *in, uint len,
| ^~~~
| int
```
Note: 'uint' is not defined there.
On glibc 'uint' comes from <sys/types.h> and happens to work on most .c files.
The change imports 'uint' declaration from '<compiler.h>'.
Bug: https://bugs.gentoo.org/703132
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
The build failure was originally reported on arm64-musl
target at https://bugs.gentoo.org/703132. Here is the amd64-musl
variant:
```
$ LANG=C make CROSS_COMPILE=x86_64-gentoo-linux-musl- tools-only_defconfig -j$(nproc)
$ LANG=C make CROSS_COMPILE=x86_64-gentoo-linux-musl- tools-all -j$(nproc)
...
In file included from tools/env/../../env/flags.c:7,
from tools/env/env_flags.c:1:
include/env.h:159:1: error: unknown type name 'ulong'; did you mean 'long'?
159 | ulong env_get_ulong(const char *name, int base, ulong default_val);
| ^~~~~
| long
```
Note: 'ulong' is not defined there.
On glibc 'ulong' comes from <sys/types.h>:
```c
/* Old compatibility names for C types. */
typedef unsigned long int ulong;
```
On musl it comes from <sys/types.h> as well but from under different guards:
```c
typedef unsigned long u_long, ulong;
```
The change inlines 'ulong' define similar to 'uint' define.
Bug: https://bugs.gentoo.org/703132
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
- Fix latest mainline kernel for rk3308
- Update rk3288-evb config to suport OP-TEE
- Fix for firefly-px30 DEBUG_UART channel and make it standalone
- Script make_fit_atf add python3 support
- Fix rk3328 timer with correct COUNTER_FREQUENCY
- Fix rk3328 ATF support with enable spl-fifo-mode
The arch timer needs COUNTER_FREQUENCY to get correct counter, add it to
make the timer works correct.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The omap3_beagle NAND ECC scheme was changed in 4b37928d35 for unknown
reasons, leading to uncorrectible ecc errors. This commit changes it
back to what it was before.
Signed-off-by: Patrik Dahlström <risca@dalakolonin.se>
Passing earlycon string in the command line may be
useful during bring up, but not after such phase.
Remove the earlycon string to align with the other i.MX SoCs
command lines.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
U-Boot binary has grown in such a way that it goes beyond the reserved
area for the environment variables.
Running "saveenv" followed by a "reset" causes U-Boot to hang because
of this overlap.
Fix this problem by increasing the CONFIG_ENV_OFFSET size.
Also, in order to prevent this same problem to happen in the future,
use CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time.
CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare
CONFIG_ENV_OFFSET with its direct value instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
After the DM conversion the boot SD card is now device 3.
Adjust it so that we can boot the kernel again.
While at it avoid a hardcoded mmc dev inside the finduuid script.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
When compile the curren mainline linux kernel(Linux 5.5-rc3)
with defconfig, the final Image is 29M, it's much
larger than Linux 5.4.
On the current u-boot side on rk3308, the gap between
kernel and fdt is 25M, the fdt will overwrite kernel
Image, so move ftd to a higher memory to give 34M
gab for them.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable DP_PWR signal to power the DP to HDMI converter cable.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Maximum size of secure boot header to be read from MMC is
12KB which spans across 0x20 blocks.
Hence increase the mmc read size for secure boot
headers from MMC to 0x20 blocks.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for DPSPARSER object (create/destroy, open/close, apply spb)
which is required to configure Soft Parser by using MC.
Also add uboot command to apply Soft Parser Blob with command:
fsl_mc apply spb <spb_load_addr>
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_CONS_INDEX is nowhere used for this board, we can drop it.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
We can use the existing CONFIG_SYS_CONFIG_NAME define for that and
remove the option. Also fix the boot string for all km83xx boards.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Remove this from the board header files and move it to Kconfig. Also use
the correct default address for kmtegr1.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
On kmtegr1 we have to specify the second localbus clock signal also
instead of using the default for our ppc 8309 boards.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
JESD216 allow vendors to define their own SFDP tables.
Add SST SFDP parser. The vendor table is allocated using resource-managed
kmalloc - the table will be freed on driver detach. It will be accessible
by getting the UCLASS_SPI_FLASH's private data.
The SST's SFDP table is particularly of interest because contains
pre-programmed globally unique EUI-48 and EUI-64 identifiers.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Add ability to query size of eeprom device and partitions
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Some devices (2 wire eeproms for example) use some bits from the chip
address to represent the high bits of the offset instead of or as well
as using multiple bytes for the offset, effectively stealing chip
addresses on the bus.
Add a chip offset mask that can be set for any i2c chip which gets
filled with the offset overflow during offset setup.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add support for coral which is a range of Apollo Lake-based Chromebook
released in 2017. This also includes reef released in 2016, since it is
based on the same SoC.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Binman supports writing the position and size of U-Boot proper and SPL
into the previous phase of U-Boot. This allows the next phase to be easily
located and loaded.
Add functions to return these useful values, along with symbols to allow
TPL to load SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function is specific to qemu so it seems best to keep it separate
from the generic code.
Move it out to a new file and update the condition to use if() instead of
#ifdef
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With of-platdata we need to create drivers for particular chips, or at
least drivers that are separate from the standard code, since C structures
are created by dtoc which are private to that driver.
To avoid duplicating the probing code, export this probe function for use
by these drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we have to have an xfer() method even if it does nothing. This
is not correct, so fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With FSP2 we need to run silicon init early after relocation. Add a new
hook for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add support for some important configuration options and FSP memory init.
The memory init uses swizzle tables from the device tree.
Support for the FSP_S binary is also included.
Bootstage timing is used for both FSP_M and FSP_S and memory-mapped SPI
reads.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update this uclass to support the needs of the Apollo Lake ITSS. It
supports four operations.
Move the uclass into a separate directory so that sandbox can use it too.
Add a new Kconfig to control it and enable this on x86.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Primary-to-Sideband bus (P2SB) is used to access various peripherals
through memory-mapped I/O in a large chunk of PCI space. The space is
segmented into different channels and peripherals are accessed by
device-specific means within those channels. Devices should be added in
the device tree as subnodes of the p2sb.
This adds a uclass and enables it for sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Intel x86 SoCs have a power manager/controller which handles several
power-related aspects of the platform. Add a uclass for this, with a few
useful operations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Early in boot it is necessary to decode the PCI device/function values for
particular peripherals in the device tree or of-platdata. This is needed
in TPL where CONFIG_PCI is not defined.
To handle this, move pci_get_devfn() into a file that is built even when
CONFIG_PCI is not defined.
Also add a function for use by of-platdata, to convert a reg property to
a pci_dev_t.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present PCI auto-configuration happens in U-Boot both before and after
relocation. This is a waste of time and may mess up static addresses used
in board_init_f(). Adjust the code to supporting doing auto-configuration
once, after relocation, under control of a device-tree property.
This is needed for Apollo Lake for debugging the silicon-init code. Once
the UART is moved to a different MMIO address the debug UART does not work
and any debug output in Apollo Lake's arch_fsp_init_r() causes a hang.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If the offset is -1 this function correctly sets up a null ofnode. But if
the offset is any other negative number (e.g. -FDT_ERR_BADPATH) then it
does the wrong thing.
An offset of -1 in ofnode indicates that the ofnode is not valid. Any
other negative value is not handled by ofnode_valid(). We could of course
change that function, but it seems much better to always use the same
value for an invalid node.
Fix it by setting the offset to -1 if it is invalid for any reason.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
SPL and TPL can access information about binman entries using link-time
symbols but this is not available in U-Boot proper. Of course it could be
made available, but the intention is to just read the device tree.
Add support for this, so that U-Boot can locate entries.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With commit 37db55b7e9 ("linux/types.h: fix typo unchar") we have a
duplicate typedef for uchar. As linux/types.h is included in common.h we
don't need another typedef for uchar there.
Fixes: 37db55b7e9 ("linux/types.h: fix typo unchar")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
- Increase stack size to avoid a stack overflow during distro boot.
- Add hifive-unleashed-a00.dts for SIFIVE FU540.
- Add OF_SEPARATE support for SIFIVE FU540.
- Add SPL support for Andes AX25 AE350.
- Improve U-Boot SPL / OpenSBI smp boot flow for RISC-V.
OpenSBI uses a relocation lottery to determine the hart to relocate
OpenSBI to its link address. In the U-Boot SPL boot flow, the main hart
schedules the secondary harts to enter OpenSBI before doing so itself.
One of the secondary harts will therefore always be the winner of the
relocation lottery. This is problematic if the link address ranges of
OpenSBI and U-Boot SPL overlap. OpenSBI will be relocated and therefore
overwrite U-Boot SPL while some harts may still run it, leading to code
corruption.
Avoid this problem by specifying the main hart as the preferred boot
hart to perform the OpenSBI relocation. The main hart will be the last
hart to enter OpenSBI, relocation can therefore occur safely.
The boot hart field was added to version 2 of the OpenSBI FW_DYNAMIC
info structure. The header file include/opensbi.h is synchronized with
include/sbi/fw_dynamic.h from the OpenSBI project to update the info
structure. The header file is recent as of commit
7a13beb21326 ("firmware: Add preferred boot HART field in struct
fw_dynamic_info").
Reported-by: Rick Chen <rick@andestech.com>
Suggested-by: Anup Patel <Anup.Patel@wdc.com>
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Rick Chen <rick@andestech.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
This patch provides four configurations which can support U-Boot SPL
to boot from RAM or FLASH and then boot FIT image including OpenSBI
FW_DYNAMIC firmware and U-Boot proper images from RAM or MMC boot devices.
With ae350_rv[32|64]_spl_defconfigs:
U-Boot SPL will be loaded by gdb or FSBL and runs in RAM in machine mode
and then load FIT image from RAM device on AE350.
With ae350_rv[32|64]_spl_xip_defconfigs:
U-Boot SPL can be burned into SPI flash and run in flash in machine mode
and then load FIT image from SPI flash or MMC device on AE350.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
Implement dma_get_cfg() interface to pass flow id information for DMA
clients to use. This is needed because on K3 SoCs, CPSW (ethernet) and
UDMA (DMA provider) support "flows" within a given RX DMA channel. This
allows different network packets to be segregated while using same RX
DMA channel. In order for basic ethernet to work, CPSW slave must be
aware of the flow ID allocated for the RX channel by the DMA driver.
This interface allows CPSW to query flow ID from DMA provider and
configure it in CPSW HW.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Sometimes, there would be a need to exchange data between DMA provider
and DMA client which are very specific to DMA driver of the SoC/platform
and are not generic enough to be put into struct dma. Therefore, introduce
dma_get_cfg() interface to get DMA provider specific data from client
device. Clients can use unique configuration ID flags to get different
configuration data from DMA driver.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
The function connects an ethernet device to a PHY using DT information.
This API is only available for eth devices with an associated device tree
node.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Renamed dm_mdio_phy_connect arguments dev to mdiodev and addr to phyaddr
for a bit more clarity and consistency with the following patches.
Also use NULL instead of 0 on error return path.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This is useful to carry custom information between the driver structure
associated with a specific HW and the driver code.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Drivers currently use XGMII for XFI and USXGMII and, where needed, use
other information to identify the actual protocol on the board. With these
two defined drivers can now rely on DT phy-mode property.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Based on commit 980066e6d964 ("dt-bindings: phy: dp83867: Add documentation
for disabling clock output") of mainline linux kernel.
The clock output is generally only used for testing and development and not
used to daisy-chain PHYs. It's just a source of RF noise afterward.
Add a mux value for "off". I've added it as another enumeration to the
output property. In the actual PHY, the mux and the output enable are
independently controllable. However, it doesn't seem useful to be able
to describe the mux setting when the output is disabled.
Document that PHY's default setting will be left as is if the property
is omitted.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Part of the env cleanup moved this out of the environment code and into
the net code. However, this helper is sometimes needed even when the net
stack isn't included.
Move the helper to lib/net_utils.c like it's similarly-purposed
string_to_ip(). Also rename the moved function to similar naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Ondrej Jirman <megous@megous.com>
unsigned char should be called uchar and not unchar.
This fixes a build error in lib/crypto/x509_cert_parser.c.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
-----BEGIN PGP SIGNATURE-----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=L2zo
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191209' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Fixes for 2020.01
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
Imported from linux kernel v5.3:
pkcs7.asn1 without changes
pkcs7.h with changes marked as __UBOOT__
pkcs7_parser.h without changes
pkcs7_parser.c with changes marked as __UBOOT__
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Imported from linux kernel v5.3:
rsapubkey.asn1 without changes
rsa.h without changes
rsa_helper.c with changes marked as __UBOOT__
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Imported from linux kernel v5.3:
asymmetric-type.h with changes marked as __UBOOT__
asymmetric_type.c with changes marked as __UBOOT__
public_key.h with changes marked as __UBOOT__
public_key.c with changes marked as __UBOOT__
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Imported from linux kernel v5.3:
build_OID_registry without changes
oid_registry.h without changes
oid_registry.c with changes marked as __UBOOT__
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Imported from linux kernel v5.3:
asn1.h without changes
asn1_ber_bytecode.h without changes
asn1_decoder.h without changes
asn1_compiler.c without changes
This host command will be used to create a ASN1 parser, for example,
for pkcs7 messages or x509 certificates. More specifically, it will
generate *byte code* which will be interpreted by asn1 decoder library.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Adding "printk.h" will help improve portability from linux kernel
code (in my case, lib/asn1_decoder.c and others) where printf and
pr_* variant functions are used.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
This function will be used in lib/crypto/x509_cert_parser.c, which
will also be imported from linux code in a later commit.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
The default value of CONFIG_SYS_CBSIZE is too small when we need
to input long commands or when using long kernel command line.
The default value of CONFIG_SYS_MAXARGS is too small to add a long
command line, and the kernel might not boot as intended without the
complete bootargs. Increase argument buffer sizes and the number of
arguments.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Convert the board to ethernet DM support. Adjust board file accordingly,
as the board_eth_init() contains custom clock configuration required for
this board to work. Furthermore, enable FEC1 clock to make FEC1 work as
well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
In preparation for use of DDR DRAM fine-tuning upon boot,
convert the board to SPL framework instead of using DCD
tables to bring up DRAM and pinmux.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Add support for setting linux,usable-memory property in the memory
node of device tree for the kernel [1].
This property holds a base address and size, describing a
limited region in which memory may be considered available for use by
the kernel. Memory outside of this range is not available for use.
[1] https://www.kernel.org/doc/Documentation/devicetree/bindings/chosen.txt
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
U-Boot binary has grown in such a way that it goes beyond the reserved
area for the environment variables.
Running "saveenv" followed by a "reset" causes U-Boot to hang because
of this overlap.
Fix this problem by increasing the CONFIG_ENV_OFFSET size.
Also, in order to prevent this same problem in the future, use
CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time.
CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare
CONFIG_ENV_OFFSET with its direct value instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Acked-by: Joris Offouga <offougajoris@gmail.com>
Tested-by: Joris Offouga <offougajoris@gmail.com>
Recent versions of the Linux kernel with many options enabled have
grown large enough to overwrite the beginning of the initrd. For
example, the kernel I use on my Rock64 and RockPro64 is 34.1 MiB,
while only 31.5 MiB are available between kernel_addr_r and
ramdisk_addr_r.
This patch moves ramdisk_addr_r up by 32 MiB on the RK3328 and RK3399,
allowing for much larger kernels.
Signed-off-by: Ben Wolsieffer <benwolsieffer@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The 'sf' command is not supposed to rely on the MTD stack, but both
'sf' and 'nand' commands use helpers located in mtd_uboot.c. Despite
their location, these functions do not depend at all on the MTD
stack.
This file (drivers/mtd/mtd_uboot.c) is only compiled if CONFIG_MTD is
selected, which is inconsistent with the current situation. Solve this
by moving these three functions (which are only used by the above two
commands) out of mtd_uboot.c and put them in a C file only compiled
with cmd/sf.c and cmd/nand.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Don't export get_part function now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Let's be consistent and always declare CONFIG_MTD from the defconfig
file when needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
CONFIG_MTD must be reserved for the MTD core. Like any other
subsystem, prefix the symbol by DM when it comes to DM support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Add Kconfig files]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
This adds a general board file based on MT8518 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
This commit is adding the basic boot support for the MT8518 eMMC board.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
[trini: Migrate env location to defconfig, set ENV_IS_IN_MMC]
Signeed-off-by: Tom Rini <trini@konsulko.com>
Currently the omapl138_lcdk has SKIP_LOWLEVEL_INIT set.
The README states there is a variation of this for the ARM926EJ-S
which allows the board to just skip the call to lowlevel_init()
and do the normal CP15 init which enables the instruction cache.
On the da850evm, this was shown to improve startup time.
This patch switches SKIP_LOWLEVEL_INIT to SKIP_LOWLEVEL_INIT_ONLY
thus, enabling the cache.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This converts the following to Kconfig:
CONFIG_SYS_CORTINA_FW_IN_MMC
CONFIG_SYS_CORTINA_FW_IN_NAND
CONFIG_SYS_CORTINA_FW_IN_NOR
CONFIG_SYS_CORTINA_FW_IN_REMOTE
CONFIG_SYS_CORTINA_FW_IN_SPIFLASH
Signed-off-by: Tom Rini <trini@konsulko.com>
Enhance do_bootm_vxworks() to support Linux compatible standard DTB
for ARM and PPC, when the least significant bit of flags in VxWorks
bootargs is set. Otherwise it falls back to the existing bootm flow
which is now legacy.
Signed-off-by: Lihua Zhao <lihua.zhao@windriver.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These functions do not use driver model but are still used. Move them to a
new eeprom.h header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this function into the init.h header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This function can be dropped when all boards use driver model for PCI. For
now, move it into init.h with a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this function into init.h which seems to be designed for this sort
of thing. Also update the header to declare struct global_data so that it
can be included without global_data.h being needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function is not defined by any boards so the feature is not used.
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these functions into the command.h header file which is a better fit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these two functions into the irq_funcs.h header file. Also move
interrupt_handler_t as this is used by the irq_install_handler() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions do not use driver model but are fairly widely used in
U-Boot. But it is not clear that they will use driver model anytime soon,
so we don't want to label them as 'legacy'.
Move them to a new irq_func.h header file. Avoid the name 'irq.h' since it
is widely used in U-Boot already.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These are used by only one arch and only within a single file. Drop the
declarations from the common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h since they do not use driver model.
Move them over. Don't bother adding comments since these functions should
be deleted.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and update the comment
style.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in time.h so move them over and add comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a header file to house the lz4 compression function. Add a comment
while we are here, since it not even clear from the name what the function
actuall does.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this function header to serial.h since this function is clearly
related to serial. The function itself stays in console.c since we don't
have a single serial file. DM and non-DM each has a separate file so we
would have to either create a new common serial file, or repeat the
function in both serial.c and serial-uclass.c, neither of which seem
worthwhile.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The function declarations in serial.h are not in sync with what is
currently used in usbtty. Fix this by updating the header and including
it, to help catch future such problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function relates to networking, so move it out of the common.h
header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
At present this function sits in its own file but it does not really
justify it. There are similar string functions in vsprintf.h, so move it
there. Also add the missing function comment.
Use the vsprintf.h include file explicitly where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These don't need to be in common.h so move them out into a new header.
Also add some missing comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These don't need to be in common.h so move them out.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It is not good practice to write code in a header file. If it is included
multiple times then the code can cause duplicate functions.
Move the bootcount_store() and bootcount_load() functions into SPL.
Note: bootcount is a bit strange in that it uses driver model but does not
define proper drivers. This should be fixed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Drop inclusion of crc.h in common.h and use the correct header directly
instead.
With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some of these have a space before the bracket. Drop it to fix the style.
Add some missing function comments while here.
Note that u32 and u8 cannot be used here since crc.h is included on the
host side.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
We have an existing U-Boot header for the one function that this defines.
Use that instead of the linux/ one. Move over the nice comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Create a new rand.h header file and move functions into it, to reduce
the size of common.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are a few whitespace problems with this code. Tidy them up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is only used by a few files so it should not be in the common header.
Move it out.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These should be moved to driver model, but in the meantime, move them
out of the common header to help reduce its size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The deadline for migration to CONFIG_DM is v2020.01. The VCT
baords would need an almost complete rewrite of all drivers to
support driver model.
Unless someone has access to the hardware and volunteers to do the migration,
the board should be scheduled for removal.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
