Commit graph

822 commits

Author SHA1 Message Date
Simon Glass
afc84dec1c tpm: Drop two unused options
The address of the I2C TPM is now defined in the device tree so there is no
need for the CONFIG options.

Remove them from the README and board config to avoid confusion.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2015-08-31 07:57:27 -06:00
Simon Glass
c294ac5c16 net: e1000: Add Kconfig options
Add Kconfig options in preparation for moving boards to use Kconfig.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-08-21 16:33:39 -05:00
Nishanth Menon
a615d0be6a ARM: Introduce erratum workaround for 801819
Add workaround for Cortex-A15 ARM erratum 801819 which says in summary
that "A livelock can occur in the L2 cache arbitration that might
prevent a snoop from completing. Under certain conditions this can
cause the system to deadlock. "

Recommended workaround is as follows:
Do both of the following:

1) Do not use the write-back no-allocate memory type.
2) Do not issue write-back cacheable stores at any time when the cache
is disabled (SCTLR.C=0) and the MMU is enabled (SCTLR.M=1). Because it
is implementation defined whether cacheable stores update the cache when
the cache is disabled it is not expected that any portable code will
execute cacheable stores when the cache is disabled.

For implementations of Cortex-A15 configured without the “L2 arbitration
register slice” option (typically one or two core systems), you must
also do the following:

3) Disable write-streaming in each CPU by setting ACTLR[28:25] = 0b1111

So, we provide an option to disable write streaming on OMAP5 and DRA7.
It is a rare condition to occur and may be enabled selectively based
on platform acceptance of risk.

Applies to: A15 revisions r2p0, r2p1, r2p2, r2p3 or r2p4 and REVIDR[3]
is set to 0.

Note: certain unicore SoCs *might* not have REVIDR[3] not set, but
might not meet the condition for the erratum to occur when they donot
have ACP (Accelerator Coherency Port) hooked to ACE (AXI Coherency
Extensions). Such SoCs will need the work around handled in the SoC
specific manner, since there is no ARM generic manner to detect such
configurations.

Based on ARM errata Document revision 18.0 (22 Nov 2013)

Suggested-by: Richard Woodruff <r-woodruff2@ti.com>
Suggested-by: Brad Griffis <bgriffis@ti.com>
Reviewed-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2015-08-12 20:47:49 -04:00
Paul Kocialkowski
f3f431a712 Reproducible U-Boot build support, using SOURCE_DATE_EPOCH
In order to achieve reproducible builds in U-Boot, timestamps that are defined
at build-time have to be somewhat eliminated. The SOURCE_DATE_EPOCH environment
variable allows setting a fixed value for those timestamps.

Simply by setting SOURCE_DATE_EPOCH to a fixed value, a number of targets can be
built reproducibly. This is the case for e.g. sunxi devices.

However, some other devices might need some more tweaks, especially regarding
the image generation tools.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-07-27 15:03:14 -04:00
Paul Kocialkowski
a588d99ac1 usb: CONFIG_USB_FASTBOOT prefix replacement for consistency
FASTBOOT is defined both by CONFIG_USB_FUNCTION_FASTBOOT AND CONFIG_CMD_FASTBOOT, so it doesn't
make much sense to have a CONFIG_USB_FASTBOOT prefix for fastboot-specific options, especially
given that other config options for fastboot use the CONFIG_FASTBOOT prefix.

This replaces the CONFIG_USB_FASTBOOT prefix with CONFIG_FASTBOOT, for consistency.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-07-22 08:57:54 +02:00
Paul Kocialkowski
17da3c0c8c usb: Fastboot function config for better consistency with other functions
USB download gadget functions such as thor and dfu have a separate config option
for the USB gadget part of the code, independent from the command part.
This switches the fastboot USB gadget to the same scheme, for better
consistency.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>

Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
2015-07-22 08:57:53 +02:00
Paul Kocialkowski
01acd6abbd usb: USB download gadget and functions config options coherent naming
This introduces a coherent scheme for naming USB download gadget and functions
config options. The download USB gadget config option is moved to
CONFIG_USB_GADGET_DOWNLOAD for better consistency with other gadgets and each
function's config option is moved to a CONFIG_USB_FUNCTION_ prefix.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>

Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
2015-07-22 08:57:53 +02:00
Prabhakar Kushwaha
5c05508971 armv8/fsl-lsch3: Support 256M mem split for MC & dbg-srvr
The agreed split of the top of memory is 256M for debug server and 256M
 for MC. This patch implements the split.

 In addition, the MC mem must be 512MB aligned, so the amount of memory
 to hide must be 512MB to achieve that alignment.

Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-20 11:44:36 -07:00
Jagan Teki
23cbd16db6 README: Remove CONFIG_SPI_FLASH_DATAFLASH help text
Since the help text is added in drivers/mtd/spi/Kconfig

Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-07-01 21:39:06 +05:30
Jagan Teki
afdfe387cd README: Remove CONFIG_SPI_FLASH_BAR help text
Since the help text is added in drivers/mtd/spi/Kconfig

Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-07-01 21:39:06 +05:30
Jagan Teki
0c79bde479 README: Remove CONFIG_SPI_FLASH_MTD help text
Since the help text is added in drivers/mtd/spi/Kconfig

Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-07-01 21:39:05 +05:30
Jagan Teki
a128197b81 README: Add CONFIG_SPI_FLASH_DATAFLASH description
This patch adds CONFIG_SPI_FLASH_DATAFLASH descrition on README
file for more readble for users.

Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-07-01 21:15:04 +05:30
Daniel Schwierzeck
9fe6d8716e mtd, spi: Add MTD layer driver
Add MTD layer driver for spi, original patch from:
http://git.denx.de/?p=u-boot/u-boot-mips.git;a=commitdiff;h=bb246819cdc90493dd7089eaa51b9e639765cced

Changes from Heiko Schocher against this patch:
- Remove compile error if not defining CONFIG_SPI_FLASH_MTD:

  LD      drivers/mtd/spi/built-in.o
drivers/mtd/spi/sf_probe.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
drivers/mtd/spi/sf_ops.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
make[1]: *** [drivers/mtd/spi/built-in.o] Fehler 1
make: *** [drivers/mtd/spi] Fehler 2

- Add a README entry.
- Add correct writebufsize, to fit with Linux v3.14
  MTD, UBI/UBIFS sync.

Note (From Jagan): For testing raw mtd parition erase/read/write operations
using cmd_sf, sf_mtd should be required to register the spi flash device to
MTD layer but the sf_mtd_info ops were not required until and unless if we
use any flash filesystem layer say for example UBI. Due to this the foot-print
got increased ~290bytes in non-UBI case here that should be acceptible.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Jagannadh Teki <jteki@openedev.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
2015-06-30 00:40:11 +05:30
Joe Hershberger
ef0f2f5752 Move defaults from config_cmd_default.h to Kconfig
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-25 22:18:34 -04:00
Chris Packham
3b10cf120b README: Describe CONFIG_SYS_NO_FLASH
Unlike most configuration options defining this actually disables
support for a feature (parallel flash). Eventually the logic behind this
should probably be flipped so that '#ifndef CONFIG_SYS_NO_FLASH' becomes
'#ifdef CONFIG_HAS_PARALLEL_FLASH' but for now lets document the
existing behaviour.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2015-06-19 16:46:50 -04:00
Stefan Roese
2d908fa084 autoboot.c: Remove CONFIG_AUTOBOOT_STOP_STR2 and CONFIG_AUTOBOOT_DELAY_STR2
These defines for a 2nd autoboot stop and delay string are nearly unused. Only
sc3 defines CONFIG_AUTOBOOT_DELAY_STR2. And a patch to remove this most likely
unmaintained board is also posted to the list.

By removing these defines the code will become cleaner and moving the remaining
compile options to Kconfig will get easier.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
2015-06-08 10:45:11 -04:00
Joe Hershberger
bdf1fe4e68 env: Add regex support to env_attrs
Allow the features that use env_attrs to specify regexs for the name

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-05-21 09:13:19 -04:00
Tom Rini
3238639d40 Merge git://git.denx.de/u-boot-net 2015-05-20 15:57:55 -04:00
Joe Hershberger
92ac520821 net: Remove all references to CONFIG_ETHADDR and friends
We really don't want boards defining fixed MAC addresses in their config
so we just remove the option to set it in a fixed way. If you must have
a MAC address that was not provisioned, then use the random MAC address
functionality.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-05-19 13:33:21 -05:00
Joe Hershberger
bef1014b31 net: Implement random ethaddr fallback in eth.c
Implement the random ethaddr fallback in eth.c so it is in a common
place and not reimplemented in each board or driver that wants this
behavior.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-05-19 13:33:21 -05:00
Hans de Goede
a8552c7c9b console: Fix pre-console flushing via cfb_console being very slow
On my A10 OlinuxIno Lime I noticed a huge (5+ seconds) delay coming from
console_init_r. This turns out to be caused by the preconsole buffer flushing
to the cfb_console. The Lime only has a 16 bit memory bus and that is already
heavy used to scan out the 1920x1080 framebuffer.

The problem is that print_pre_console_buffer() was printing the buffer once
character at a time and the cfb_console code then ends up doing a cache-flush
for touched display lines for each character.

This commit fixes this by first building a 0 terminated buffer and then
printing it in one puts() call, avoiding unnecessary cache flushes.

This changes the time for the flush from 5+ seconds to not noticable.

The downside of this approach is that the pre-console buffer needs to fit
on the stack, this is not that much to ask since we are talking about plain
text here. This commit also adjusts the sunxi CONFIG_PRE_CON_BUF_SZ to
actually fit on the stack. Sunxi currently is the only user of the pre-console
code so no other boards need to be adjusted.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-05-19 18:37:30 +02:00
Fabio Estevam
aed9fed975 README: fix typo in 'currently'
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-05-08 17:24:17 -04:00
Bin Meng
5098d73e86 x86: Remove the old VGA driver
CONFIG_VIDEO_VGA is no longer needed thus remove it.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-29 18:51:48 -06:00
Tom Rini
cc555bd4f4 Merge branch 'master' of git://git.denx.de/u-boot-spi 2015-04-28 07:28:43 -04:00
York Sun
207774b213 armv8/ls2085a: Fix generic timer clock source
The timer clock is system clock divided by 4, not fixed 12MHz.
This is common to the SoC, not board specific. Primary core is
fixed when u-boot still runs in board_f. Secondary cores are
fixed by reading a variable set by u-boot.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Mark Rutland <mark.rutland@arm.com>
2015-04-23 08:55:55 -07:00
York Sun
4516ff8160 driver/ddr/fsl: Add built-in memory test for DDR4 driver
Add built-in memory test to catch errors after DDR is initialized, before
any other transactions. To enable this test, define CONFIG_FSL_DDR_BIST.
An environmental variable "ddr_bist" is checked before starting test.
It takes a while (several seconds) depending on system memory size.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23 08:55:53 -07:00
York Sun
f8cb101e1e driver/i2c/mxc: Enable I2C bus 3 and 4
Some SoCs have more than two I2C busses. Instead of adding ifdef
to the driver, macros are put into board header file where
CONFIG_SYS_I2C_MXC is defined.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Heiko Schocher <hs@denx.de>
2015-04-23 08:55:53 -07:00
Jagannadha Sutradharudu Teki
122d805fd4 Revert "spi: add config option to enable the WP pin function on st micron flashes"
This reverts commit 562f8df18d.

Note: Even un-reverting this patch couldn't works as expected, based
on the latest testing from Heiko Schocher.

Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
2015-04-23 19:53:29 +05:30
Tom Rini
1733259d25 Merge branch 'master' of git://git.denx.de/u-boot-video 2015-04-20 09:13:52 -04:00
Simon Glass
ee2b24340f Kconfig: Move CONFIG_BOOTSTAGE to Kconfig
Move CONFIG_BOOT_STAGE and its associated options to Kconfig. Adjust
existing users and code.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:37 -06:00
Joe Hershberger
bc0571fc10 net: cosmetic: Fix checkpatch.pl failures in net.c
Finish eliminating CamelCase from net.c and other failures

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:35 -06:00
Hannes Petermaier
604c7d4a5a common/lcd_console: introduce display/framebuffer rotation
Sometimes, for example if the display is mounted in portrait mode or even if it
is mounted landscape but rotated by 180 degrees, we need to rotate our content
of the display respectively the framebuffer, so that user can read the messages
which are printed out.

For this we introduce the feature called "CONFIG_LCD_ROTATION", this may be
defined in the board-configuration if needed. After this the lcd_console will
be initialized with a given rotation from "vl_rot" out of "vidinfo_t" which is
provided by the board specific code.

If CONFIG_LCD_ROTATION is not defined, the console will be initialized with
0 degrees rotation.

Signed-off-by: Hannes Petermaier <hannes.petermaier@br-automation.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
[agust: fixed 'struct vidinfo' has no member named 'vl_rot' errors]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2015-04-18 17:40:37 +02:00
Albert ARIBAUD \(3ADEV\)
8c80eb3b53 Introduce CONFIG_SPL_PANIC_ON_RAW_IMAGE
introduce CONFIG_SPL_PANIC_ON_RAW_IMAGE.
An SPL which define this will panic() if the
image it has loaded does not have a mkimage
signature.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10 14:23:37 +02:00
Peter Tyser
073adf987e nand: Remove CONFIG_MTD_NAND_VERIFY_WRITE
The CONFIG_MTD_NAND_VERIFY_WRITE has been removed from Linux for some
time and a more generic method of NAND verification now exists in U-Boot.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2015-03-30 23:24:39 -05:00
Masahiro Yamada
0a12e6872e generic-board: move __HAVE_ARCH_GENERIC_BOARD to Kconfig
Move the option to Kconfig renaming it to CONFIG_HAVE_GENERIC_BOARD.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-03-28 09:03:08 -04:00
Masahiro Yamada
3bde6888c0 README: remove description about driver model configuration options (again)
The Driver Model description in README was removed by commit
65eb659e56 (README: remove description about driver model
configuration options), and was revived by mistake by commit
b79dadf846 when resolving the conflict.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-03-13 09:29:36 -04:00
Nishanth Menon
9b4d65f918 ARM: Introduce erratum workaround for 621766
621766: Under a specific set of conditions, executing a sequence of
	NEON or vfp load instructions can cause processor deadlock
Impacts: Every Cortex-A8 processors with revision lower than r2p1
Work around: Set L1NEON to 1

Based on ARM errata Document revision 20.0 (13 Nov 2010)

Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:28:53 -04:00
Nishanth Menon
5902f4ce0f ARM: Introduce erratum workaround for 430973
430973: Stale prediction on replaced inter working branch causes
	Cortex-A8 to execute in the wrong ARM/Thumb state
Impacts: Every Cortex-A8 processors with revision lower than r2p1
Work around: Set IBE to 1

Based on ARM errata Document revision 20.0 (13 Nov 2010)

Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:28:52 -04:00
Nishanth Menon
b45c48a7c3 ARM: Introduce erratum workaround for 454179
454179: Stale prediction may inhibit target address misprediction on
	next predicted taken branch
Impacts: Every Cortex-A8 processors with revision lower than r2p1
Work around:  Set IBE and disable branch size mispredict to 1

Also provide a hook for SoC specific handling to take place if needed.

Based on ARM errata Document revision 20.0 (13 Nov 2010)

Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:28:48 -04:00
Nishanth Menon
c616a0df29 ARM: Introduce erratum workaround for 798870
Add workaround for Cortex-A15 ARM erratum 798870 which says
"If back-to-back speculative cache line fills (fill A and fill B) are
issued from the L1 data cache of a CPU to the L2 cache, the second
request (fill B) is then cancelled, and the second request would have
detected a hazard against a recent write or eviction (write B) to the
same cache line as fill B then the L2 logic might deadlock."

Implementations for SoC families such as Exynos, OMAP5/DRA7 etc
will be widely different.

Every SoC has slightly different manner of setting up access to L2ACLR
and similar registers since the Secure Monitor handling of Secure
Monitor Call(smc) is diverse. Hence an weak function is introduced
which may be overriden to implement SoC specific accessor implementation.

Based on ARM errata Document revision 18.0 (22 Nov 2013)

Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-03-13 09:28:29 -04:00
Tom Rini
b79dadf846 Merge branch 'master' of git://git.denx.de/u-boot-tegra
Conflicts:
	README

Signed-off-by: Tom Rini <trini@konsulko.com>
2015-03-10 19:09:18 -04:00
Masahiro Yamada
65eb659e56 README: remove description about driver model configuration options
All the DM-related configuration options are described in Kconfig
helps.  They should not be duplicated in README.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-03-05 19:13:43 -07:00
Tom Rini
02ebe6f702 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-03-05 07:22:18 -05:00
Simon Glass
db910353a1 arm: spl: Allow board_init_r() to run with a larger stack
At present SPL uses a single stack, either CONFIG_SPL_STACK or
CONFIG_SYS_INIT_SP_ADDR. Since some SPL features (such as MMC and
environment) require a lot of stack, some boards set CONFIG_SPL_STACK to
point into SDRAM. They then set up SDRAM very early, before board_init_f(),
so that the larger stack can be used.

This is an abuse of lowlevel_init(). That function should only be used for
essential start-up code which cannot be delayed. An example of a valid use is
when only part of the SPL code is visible/executable, and the SoC must be set
up so that board_init_f() can be reached. It should not be used for SDRAM
init, console init, etc.

Add a CONFIG_SPL_STACK_R option, which allows the stack to be moved to a new
address before board_init_r() is called in SPL.

The expected SPL flow (for CONFIG_SPL_FRAMEWORK) is documented in the README.

Signed-off-by: Simon Glass <sjg@chromium.org>
For version 1:
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Tom Rini <trini@konsulko.com>
2015-03-04 14:55:04 -05:00
Stephen Warren
73c38934da ARM: tegra: support running in non-secure mode
When the CPU is in non-secure (NS) mode (when running U-Boot under a
secure monitor), certain actions cannot be taken, since they would need
to write to secure-only registers. One example is configuring the ARM
architectural timer's CNTFRQ register.

We could support this in one of two ways:
1) Compile twice, once for secure mode (in which case anything goes) and
   once for non-secure mode (in which case certain actions are disabled).
   This complicates things, since everyone needs to keep track of
   different U-Boot binaries for different situations.
2) Detect NS mode at run-time, and optionally skip any impossible actions.
   This has the advantage of a single U-Boot binary working in all cases.

(2) is not possible on ARM in general, since there's no architectural way
to detect secure-vs-non-secure. However, there is a Tegra-specific way to
detect this.

This patches uses that feature to detect secure vs. NS mode on Tegra, and
uses that to:

* Skip the ARM arch timer initialization.

* Set/clear an environment variable so that boot scripts can take
  different action depending on which mode the CPU is in. This might be
  something like:
  if CPU is secure:
    load secure monitor code into RAM.
    boot secure monitor.
    secure monitor will restart (a new copy of) U-Boot in NS mode.
  else:
    execute normal boot process

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-03-04 10:08:57 -07:00
Stefano Babic
b9cb64825b Merge branch 'master' of git://git.denx.de/u-boot 2015-03-02 09:42:53 +01:00
gaurav rana
94e3c8c4fd crypto/fsl - Add progressive hashing support using hardware acceleration.
Currently only normal hashing is supported using hardware acceleration.
Added support for progressive hashing using hardware.

Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
CC: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-02-25 13:20:02 -08:00
York Sun
e32d59a2fa driver/ddr/fsl: Add sync of refresh
Add sync of refresh for multiple DDR controllers. DDRC initialization
needs to complete first. Code is re-ordered to keep refresh close.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-02-24 13:09:42 -08:00
Christian Gmeiner
189d257b7a cmd_eeprom: make it possible to define the used i2c bus
A SoC like the i.MX6 supports more then one i2c bus. In oder to be
able to use the eeprom command add a new define to specify the
i2c bus to use. If CONFIG_SYS_I2C_EEPROM_BUS is not defined there
is no functional change, else a call to i2c_set_bus_num(..) is
done before calling i2c_read(..) and i2c_write(..).

Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2015-02-17 10:42:53 +01:00
Heiko Schocher
7bae0d6f62 arm, at91, wdt: make timeout configurable
make the HW WDT timeout configurable through the define
CONFIG_AT91_HW_WDT_TIMEOUT.

Signed-off-by: Heiko Schocher <hs@denx.de>
2015-02-07 23:43:20 +01:00