Half DQ configuration seems to be very rare for H6 based boards/STBs,
but exists nevertheless. Currently the only known product which needs
this support is Tanix TX6 mini.
This commit adds support for half DQ configuration. Code was tested
for regressions on other configurations (OrangePi 3 1 GiB/LPDDR3, Tanix
TX6 4 GiB/DDR3) and none were found.
Thanks to Icenowy Zheng for help with this code.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: thomas graichen <thomas.graichen@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Add some basic line delay values to be used with DDR3 DRAM chips on
some H6 TV boxes.
Taken from a register dump after boot0 initialised the DRAM.
Put them as the default delay values for DDR3 DRAM until we know better.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
At the moment the H6 DRAM driver only supports LPDDR3 DRAM.
Extend the driver to cover DDR3 DRAM as well.
The changes are partly motivated by looking at the ZynqMP register
documentation, partly by looking at register dumps after boot0/libdram
has initialised the controller.
Many thanks to Jernej for contributing some fixes!
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Currently the H6 DRAM driver only supports one kind of LPDDR3 DRAM.
Split the timing parameters for this LPDDR3 configuration into a
separate file, to allow selecting an alternative later at compile time
(as the sunxi-dw driver does).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The DRAM controller manual suggests to first program the PHY
initialisation parameters to the PHY_PIR register, and then set bit 0 to
trigger the initialisation. This is also used in boot0.
Follow this recommendation by setting bit 0 in a separate step.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Using memcpy() is, however tempting, not a good idea: It depends on the
specific implementation of memcpy, also lacks barriers. In this
particular case the first registers were written using 64-bit writes,
and the last register using four separate single-byte writes.
Replace the memcpy with a proper loop using the writel() accessor.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Currently the DRAM bus gate and reset is changed at the same time in
H6 DRAM initialization code, which disobeys the user manual's
programming guide.
Fix the sequence by follow the sequence suggested by the user manual
(ungate the bus clock after release the reset signal).
By some experiments it seems to fix the DRAM size detection failure that
rarely happens.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner H6 SoC comes with a set of new DRAM controller+PHY combo.
Both the controller and the PHY seem to be originate from DesignWare,
and are similar to the ones in ZynqMP SoCs.
This commit introduces an initial DRAM driver for H6, which contains
only LPDDR3 support. The currently known SBCs with H6 all come with
LPDDR3 memory, including Pine H64 and several Orange Pi's.
The BSP DRAM initialization code is closed source and violates GPL. Code
in this commit is written by experimenting, referring the code/document
of other users of the IPs (mainly the ZynqMP, as it's the only found PHY
reference) and disassebling the BSP blob.
Thanks for Jernej Skrabec for review and fix some issues in this driver
(including the most critical one which made it to work), and rewrite
some code from register dump!
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
