This feature was only used for tegra20 seaboard that had a pinmux
conflict on the SPI pins. These boards were never manufactured, so
remove this support to clean up SPI driver.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
tegra_mmc_init() now parses the DT info for bus width, WP/CD GPIOs, etc.
Tested on Seaboard, fully functional.
Tamonten boards (medcom-wide, plutux, and tec) use a different/new
dtsi file w/common settings.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Harmony contains an SD slot with all 8 bits routed. This allows plugging
in an eMMC-chip-in-SD-form-factor.
Seaboard/Springbank/Ventana/AC100 all have an eMMC chip with all 8 bits
hooked up.
Now that the U-Boot eMMC code fully supports 8-bit operation, initialize
those ports as 8-bit instead of 4-bit to improve performance.
Whistler was already registering its ports as 8-bit.
TrimSlice doesn't have any 8-bit ports.
I don't have any Avionic Design boards nor the Colibri board to test with.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Seaboard has a GPIO that switches an external mux between Tegra's debug
UART and SPI flash. This is initialized from the SPL so that SPL debug
output can be seen. Simplify the code that does this, and don't actually
request the GPIO in the SPL; just program it. This saves ~4.5K from the
size of the SPL, mostly BSS due to the large gpio_names[] table that is
no longer required. This makes Seaboard's SPL fit within the current max
size.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Allen Martin <amartin@nvidia.com>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Seaboard and Ventana are very similar boards, and so share the seaboard.c
board file. The one difference needed so far is detected at run-time by
calling machine_is_ventana(). This bloats the Ventana build with code
that is never used. Switch to detecting Ventana at compile time to remove
bloat. This shaves ~5K off the SPL size on Ventana, and makes the SPL fit
within the max size.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Rename board provided gpio_config_uart() to
gpio_early_init_uart() as it does the same thing as the equally
called function provided by the uart-switch code. This allows
to simply call this function in early board init whether or not
we are building with CONFIG_UART_SWITCH defined.
Also provide a weak symbol for this function, to avoid the
need to provide this function for boards that don't need any
fixup.
This patch supersedes the earlier posted
"tegra: convert gpio_config_uart to weak symbol".
Build tested with MAKEALL -s tegra20
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h.
Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs
that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20'
'root' file.
All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate.
Convert tegra20_ source file and function names to tegra_, also.
Upcoming Tegra30 port will use common code/defines/names where possible.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
None of harmony, seaboard, ventana, whistler directly build files from
../common/, so there's no need to mkdir the obj directory for such files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is make naming consistent with the kernel and devicetree and in
preparation of pulling out the common tegra20 code.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In anticipation of Tegra3 support, continue removing/renaming
Tegra2-specific files. No functional changes (yet).
Updated copyrights to 2012.
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds basic USB support for port 0. The other port is not supported
yet.
Tegra2 (SeaBoard) # usb start
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 5 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Tegra2 (SeaBoard) # ext2load usb 0:3 10000000 /boot/vmlinuz
Loading file "/boot/vmlinuz" from usb device 0:3 (ROOT-A)
2932976 bytes read
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use the new funcmux_select() feature to set up the MMC pin mux.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
tegra2_mmc_init() is implemented by the Tegra2 MMC driver. Since most of
the Tegra2-based boards will need to call it, this commit exports it in
the new public asm/arch/mmc.h header file to prevent each board from
providing its own prototype.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On Seaboard the UART and SPI interfere with each other. This causes the UART
to receive spurious zero bytes after SPI transactions and also means that
SPI can corrupt a few output characters when it starts up if they are still
in the UART buffer.
This updates the board to use the SPI/UART switch to avoid the problem.
For now this feature is turned off since it needs changes to the NS16550
UART to operate.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra2 Seaboard has the unfortunate feature that SPI and the console
UART are multiplexed on the same pins. We need to switch between one
and the other during SPI and console activity.
This new file implements a switch and keeps track of which peripheral
owns the pins. It also flips over the controlling GPIO as needed
Since we are adding a second file to board/nvidia/common, we create
a proper Makefile there and remove the direct board.o include from
board/nvidia/seaboard/Makefile
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
... rather than open-coding the register accesses.
However, gpio_request() typically stores the "label" parameter in a global
data structure. This causes problems when called from gpio_config_uart(),
since the code is running before relocation. To solve this, pass a NULL
string to gpio_request(), and modify gpio_request() not to touch the string
if it's NULL.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Ventana is a board which is very similar to Seaboard. Support it by
re-using board/nvidia/seaboard/seaboard.c with minor run-time conditionals.
v5: Makefile: Use cmd_link_o_target, remove unused clean/distclean targets.
v6: Make gpio_config_uart_seaboard() static.
v7: Add MAINTAINERS entry for Ventana. Tom Warren doesn't have Ventana, so
he asked me to add myself for this board.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Pass the GPIO numbers for power and card detect to tegra2_mmc_init(), and
modify that function to perform all required GPIO initialization. This
removes the need for board files to perform these operations.
Move board_mmc_getcd() into tegra2_mmc.c now that the driver knows which
GPIOs to use.
Update affected call-sites in seaboard.c and harmony.c. Note that this
change should make all SD ports work on Harmony, since the required GPIO
setup is now being performed.
v4: Fix prototype of tegra2_mmc_init() in board.h to match driver change.
Remove prototype of gpio_config_mmc() from board.h
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Andy Fleming <afleming@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
For Seaboard, this is mostly a cut/paste of board_mmc_init() and
pin_mux_mmc() into seaboard.c; pin_mux_mmc() was modified to add some
missing pinmux_tristate_disable calls for the GPIOs.
For Harmony, those functions were modified to configure SDMMC2 (index 2)
instead of SDMMC3 (index 1), since that's what is present on the board.
However, harmony.c is still missing the required GPIO setup, so neither
port is likely to function correctly yet. This will be fixed in the next
change.
v4: Include board.h to prototype tegra2_mmc_init().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds the required GPIO and pinmux configuration to make eMMC / SD work
on Seaboard.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
Seems people fixed their files to use libfoo.o, but didn't actually
update the creation targets to use $(cmd_link_o_target). Update the
rest of the Makefile's found with grep.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Simon Glass <sjg@chromium.org>
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The out-of-tree build fails because the Makefiles in question depend on
source files of another directory but do not explicitly mkdir that
directory.
As a matter of fact, other Makefiles under board/*/ directory that refer
to source files under another directory explicitly call mkdir.
This patch adds explicit mkdir's to the Makefiles in question, and
verifies that out-of-tree build is working.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
