For printing GUIDs with macro EFI_ENTRY use %pUs instead of %pUl to provide
readable debug output.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
If variable dfu_alt_info is not defined duplicate messages are displayed.
=> efidebug boot dump
Scanning disk mmc2.blk...
Scanning disk mmc1.blk...
Scanning disk mmc0.blk...
Found 3 disks
No EFI system partition
"dfu_alt_info" env variable not defined!
Probably dfu_alt_info not defined
"dfu_alt_info" env variable not defined!
Probably dfu_alt_info not defined
Remove the 'Probably dfu_alt_info not defined' message.
Instead write a warning if the variable contains no entities.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
U-Boot, in some occasions, injects a 'kaslr-seed' property on the /chosen
node. That would be problematic in case we want to measure the DTB we
install in the configuration table, since it would change across reboots.
The Linux kernel EFI-stub completely ignores it and only relies on
EFI_RNG_PROTOCOL for it's own randomness needs (i.e the randomization
of the physical placement of the kernel). In fact it (blindly) overwrites
the existing seed if the protocol is installed. However it still uses it
for randomizing it's virtual placement.
So let's get rid of it in the presence of the RNG protocol.
It's worth noting that TPMs also provide an RNG. So if we tweak our
EFI_RNG_PROTOCOL slightly and install the protocol when a TPM device
is present the 'kaslr-seed' property will always be removed, allowing
us to reliably measure our DTB.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Currently we allow and explicitly check a single shared page with
StandAloneMM. This is dictated by OP-TEE which runs the application.
However there's no way for us dynamically discover the number of pages we
are allowed to use. Since writing big EFI signature list variable
requires more than a page, OP-TEE has bumped the number of shared pages to
four.
Let's remove our explicit check and allow the request to reach OP-TEE even
if it's bigger than what it supports. There's no need to sanitize the
number of pages internally. OP-TEE will fail if we try to write more
than it's allowed. The error will just trigger later on, during the
StMM access.
While at it add an error message to help users figure out what failed.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Ilias Apalodimas <apalos@gmail.com>
When the TCG2 protocol is installed in efi_tcg2_register(),
TPM2 device must be present.
tcg2_measure_pe_image() expects that TCP2 protocol is installed
and TPM device is available. If TCG2 Protocol is installed but
TPM device is not found, tcg2_measure_pe_image() returns
EFI_SECURITY_VIOLATION and efi_load_image() ends with failure.
The same error handling is applied to
efi_tcg2_measure_efi_app_invocation().
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
There are functions that calls tcg2_agile_log_append() outside
of the TCG protocol invocation (e.g tcg2_measure_pe_image).
These functions must to check that TCG2 protocol is installed.
If not, measurement shall be skipped.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This commit modify efi_tcg2_register() to return the
appropriate error.
With this fix, sandbox will not boot because efi_tcg2_register()
fails due to some missing feature in GetCapabilities.
So disable sandbox if EFI_TCG2_PROTOCOL is enabled.
UEFI secure boot variable measurement is not directly related
to TCG2 protocol installation, tcg2_measure_secure_boot_variable()
is moved to the separate function.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Firmwares before U-Boot may be capable of doing tpm measurements
and passing them to U-Boot in the form of eventlog. However there
may be scenarios where the firmwares don't have TPM driver and
are not capable of extending the measurements in the PCRs.
Based on TCG spec, if previous firnware has extended PCR's, PCR0
would not be 0. So, read the PCR0 to determine if the PCR's need
to be extended as eventlog is parsed or not.
Signed-off-by: Ruchika Gupta <ruchika.gupta@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Platforms may have support to measure their initial firmware components
and pass the event log to u-boot. The event log address can be passed
in property tpm_event_log_addr and tpm_event_log_size of the tpm node.
Platforms may choose their own specific mechanism to do so. A weak
function is added to check if even log has been passed to u-boot
from earlier firmware components. If available, the eventlog is parsed
to check for its correctness and further event logs are appended to the
passed log.
Signed-off-by: Ruchika Gupta <ruchika.gupta@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
If we call efi_clear_os_indications() before initializing the memory store
for UEFI variables a NULL pointer dereference occurs.
The error was observed on the sandbox with:
usb start
host bind 0 sandbox.img
load host 0:1 $kernel_addr_r helloworld.efi
bootefi $kernel_addr_r
Here efi_resister_disk() failed due to an error in the BTRFS implementation.
Move the logic to clear EFI_OS_INDICATIONS_FILE_CAPSULE_DELIVERY_SUPPORTED
to the rest of the capsule code.
If CONFIG_EFI_IGNORE_OSINDICATIONS=y, we should still clear the flag.
If OsIndications does not exist, we should not create it as it is owned by
the operating system.
Fixes: 149108a3eb ("efi_loader: clear OsIndications")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Our algorithm for creating USB device paths may lead to duplicate device
paths which result in efi_disk_register() failing. Instead we should just
skip devices that cannot be registered as EFI block devices.
Fix a memory leak in efi_disk_add_dev() caused by the duplicate device
path.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
If we look at the path that bootm/booti take when preparing to boot the
OS, we see that as part of (or prior to calling do_bootm_states,
explicitly) the process, bootm_disable_interrupts() is called prior to
announce_and_cleanup() which is where udc_disconnect() /
board_quiesce_devices() / dm_remove_devices_flags() are called from. In
the EFI path, these are called afterwards. In efi_exit_boot_services()
however we have been calling bootm_disable_interrupts() after the above
functions, as part of ensuring that we disable interrupts as required
by the spec. However, bootm_disable_interrupts() is also where we go
and call usb_stop(). While this has been fine before, on the TI J721E
platform this leads us to an exception. This exception seems likely to
be the case that we're trying to stop devices that we have already
disabled clocks for. The most direct way to handle this particular
problem is to make EFI behave like the do_bootm_states() process and
ensure we call bootm_disable_interrupts() prior to ending up in
usb_stop().
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Simon Glass <sjg@chromium.org>
Suggested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Due to U-Boot's lazy binding mentality the TPM is probed but not properly
initialized. The user can startup the device from the command line
e.g 'tpm2 startup TPM2_SU_CLEAR'. However we can initialize the TPM during
the TCG protocol installation, which is easier to use overall.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
As described in the TCG spec [1] in sections 7.1.1 and 7.1.2 the FinalEvent
table should include events after GetEventLog has been called. This
currently works for us as long as the kernel is the only EFI application
calling that. Specifically we only implement what's described in 7.1.1.
So refactor the code a bit and support EFI application(s) calling
GetEventLog. Events will now be logged in both the EventLog and FinalEvent
table as long as ExitBootServices haven't been invoked.
[1] https://trustedcomputinggroup.org/wp-content/uploads/EFI-Protocol-Specification-rev13-160330final.pdf
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Implement the EFI_EVENT_GROUP_BEFORE_EXIT_BOOT_SERVICES event group
handling.
Add the definition of EFI_EVENT_GROUP_AFTER_READY_TO_BOOT.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Record capsule update result only if the capsule file is
successfully read, because the capsule GUID is not sure when
the file can not be read or the file is not a capsule.
Without this fix, if user puts a dummy (non-capsule) file
under (ESP)EFI/UpdateCapsule, U-Boot causes a synchronous
abort.
This also fixes use-after-free bug of the 'capsule' variable.
Fixes: c74cd8bd08 ("efi_loader: capsule: add capsule_on_disk support")
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
log_info() is used for the debug level logging statement
which should use log_debug() instead. Convert it to reduce the
log output.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
UEFI specification does not require that BootOrder is defined.
In current implementation, boot variable measurement fails and
returns EFI_NOT_FOUND if BootOrder is not defined.
This commit correcly handles this case, skip the boot variable
measurement if BootOrder is not defined.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Most modern platforms use 64-bit EFI so it is useful to have a U-Boot app
that runs under that. Add a (non-functional) build for this.
Note that --whole-archive causes the gcc 9.2 linker to crash, so disable
this for now. Once this is resolved, things should work.
For now, avoid mentioning the documentation for the 64-bit app, since it
does not work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This commit adds the EFI_TCG2_PROTOCOL.SubmitCommand
required in the TCG PC Client PFP spec.
SubmitCommand enables to send the raw command to the TPM device.
To implement this api, tpm2_submit_command() is added
into tpm-v2.c.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Calling unaligned/access-ok.h version of put_unaligned_le64()
causes data abort in arm 32-bit QEMU.
The similar issue also occurs in linux kernel,
unaligned/access-ok.h is no longer used in linux kernel[1].
This commit uses the unaligned/be_byteshift.h and
unaligned/le_byteshift.h helper instead of unaligned/access-ok.h.
[1]https://lore.kernel.org/all/20210507220813.365382-8-arnd@kernel.org/
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
As we discussed in ML, currently a device tree is the only place
to store public keys for capsule authentication. So __weak is not
necessary for now.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds the DeployedMode and AuditMode variable
measurement required in TCG PC Client Platform Firmware
Profile Specification.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
This commit adds the UEFI GPT disk partition topology
measurement required in TCG PC Client Platform Firmware
Profile Specification
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
TCG PC Client Platform Firmware Profile Specification
requires to measure the SMBIOS table that contains static
configuration information (e.g. Platform Manufacturer
Enterprise Number assigned by IANA, platform model number,
Vendor and Device IDs for each SMBIOS table).
The device- and environment-dependent information such as
serial number is cleared to zero or space character for
the measurement.
Existing smbios_string() function returns pointer to the string
with const qualifier, but exisintg use case is updating version
string and const qualifier must be removed.
This commit removes const qualifier from smbios_string()
return value and reuses to clear the strings for the measurement.
This commit also fixes the following compiler warning:
lib/smbios-parser.c:59:39: warning: cast to pointer from integer of
different size [-Wint-to-pointer-cast]
const struct smbios_header *header = (struct smbios_header *)entry->struct_table_address;
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Simplify efi_sigstore_parse_sigdb() by using existing functions.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
In multiple places we need the default GUID matching a variable name.
The patch provides a library function. For secure boot related variables
like 'PK', 'KEK', 'db' a lookup table is used. For all other variable
names EFI_GLOBAL_VARIABLE is returned.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
UEFI variable names are typically constants and hence should be defined as
const. Unfortunately some of our API functions do not define the parameters
for UEFI variable names as const. This requires unnecessary conversions.
Adjust parameters of several internal functions to tre UEFI variable names
as const.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The commit 47a25e81d3 ("Revert "efi_capsule: Move signature from DTB to
.rodata"") failed to revert the removal of efi_get_public_key_data().
Add back this function and move it under lib/efi_loader so that other
platforms can utilize it. It is now declared as a weak function so that
it can be replaced with a platform-specific implementation.
Fixes: 47a25e81d3 ("Revert "efi_capsule: Move signature from DTB to
.rodata"")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This commit fixes the following compilation warning
of boottime->install_configuration_table() function.
lib/efi_selftest/efi_selftest_tcg2.c:475:46:
warning: passing argument 1 of ‘boottime->install_configuration_table’
discards ‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers]
ret = boottime->install_configuration_table(&smbios_guid, dmi);
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The 'efidebug boot dump' command should not display the VenMedia() device
path node preceding the device path of the initial ram disk.
By letting efi_dp_from_lo() skip the VenMedia() device path node we can
simplify the coding.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Create the GUID as a global variable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Parameter size is never used in function efi_dp_from_lo(). Remove it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Instead of copying a GUID and then using a pointer to the copy for calling
guidcmp(), just pass the pointer to the orginal GUID.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We are ignoring the alignment communicated via the PE/COFF header.
Starting 5.10 the Linux kernel will loudly complain about it. For more
details look at [1] (in linux kernel).
So add a function that can allocate aligned EFI memory and use it for our
relocated loaded image.
[1] c32ac11da3f83 ("efi/libstub: arm64: Double check image alignment at entry")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Vincent Stehlé <vincent.stehle@arm.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When using a file to store UEFI variables we must make sure that secure
boot related variables are not loaded from this file. With commit
9ef82e2947 ("efi_loader: don't load signature database from file")
this has already been implemented for variables defined in the UEFI
specification. As most Linux distributions use Shim we should do the same
for Shim's MOK database.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This code should never have been added as it builds a new feature on top
of legacy code. This has already been improved with the dependency on BLK.
Add a dependency on DM_ETH also, to avoid needing to deal with this old
code.
Boards which want EFI_LOADER should migrate to driver model first.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Convert pixel values when necessary like we do for 16bpp
framebuffers.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At present EFI_SECURE BOOT selects RSA but does not necessarily enable
FIT_SIGNATURE. Mostly this is fine, but a few boards do not enable it,
so U-Boot tries to do RSA verification when loading FIT images, but it
is not enabled.
This worked because the condition for checking the RSA signature is
wrong in the fit_image_verify_with_data() function. In order to fix it
we need to fix this dependency. Make sure that FIT_SIGNATURE is enabled
so that RSA can be used.
It might be better to avoid using 'select' in this situation.
Signed-off-by: Simon Glass <sjg@chromium.org>
TCG EFI Protocol Specification defines the number_of_algorithms
field in spec ID event to be equal to the number of active
algorithms supported by the TPM device. In current implementation,
this field is populated with the count of all algorithms supported
by the TPM which leads to incorrect spec ID event creation.
Similarly, the algorithm array in spec ID event should be a variable
length array with length being equal to the number_of_algorithms field.
In current implementation this is defined as a fixed length array
which has been fixed.
Signed-off-by: Ruchika Gupta <ruchika.gupta@linaro.org>
CC: Masahisa Kojima <masahisa.kojima@linaro.org>
CC: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This was unfortunately applied despite much discussion about it beiong
the wrong way to implement this feature.
Revert it before too many other things are built on top of it.
This reverts commit ddf67daac3.
Signed-off-by: Simon Glass <sjg@chromium.org>
More C files do not use compile time timestamp macros and do not have to be
recompiled every time when SOURCE_DATE_EPOCH changes.
This patch moves version_string[] from version.h to version_string.h and
updates other C files which only needs version_string[] string to include
version_string.h instead of version.h. After applying this patch these
files are not recompiled every time when SOURCE_DATE_EPOCH changes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Macro U_BOOT_VERSION_STRING is already stored in variable version_string.
So use directly this variable instead of storing U_BOOT_VERSION_STRING into
temporary variable.
Signed-off-by: Pali Rohár <pali@kernel.org>
[trini: This area was reworked since posted, what is here is now really
inspired by the previous version, so drop Ilias' Acked-by]
Signed-off-by: Tom Rini <trini@konsulko.com>
There is two unneeded EFI_CALL references in tcg2_measure_pe_image().
The first one in efi_search_protocol() and the second on in the device path
calculation. The second isn't even a function we should be calling, but a
pointer assignment, which happens to work with the existing macro.
While at it switch the malloc call to a calloc, remove the unnecessary cast
and get rid of an unneeded if statement before copying the device path
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The move to driver model should by now be completed. To be able to remove
pre-driver model code from our block IO code require CONFIG_BLK=y for UEFI
support.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
boot_service_capability_min is constant, it should be capitalized.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When dropping SHA512_ALGO in general, we didn't catch some cases where
an option was selecting both SHA512 and SHA512_ALGO and caused them to
select SHA512 twice. Kconfig doesn't complain, but this is still wrong
and should be corrected.
Fixes: e60e449931 ("lib: Drop SHA512_ALGO in lieu of SHA512")
Reported-by: Andreas Schwab <schwab@suse.de>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
SHA512_ALGO was used as a "either SHA512 or SHA384", although the
implementations of these two algorithms share a majority of code.
From a Kconfig interface perspective, it makes sense to present two
distinct options. This requires #ifdefing out the SHA512
implementation from sha512.c. The latter doesn't make any sense.
It's reasonable to say in Kconfig that SHA384 depends on SHA512, and
seems to be the more polite way to handle the selection.
Thus, automatically select SHA512 when SHA384 is enabled.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
TCG EFI Protocol Specification defines that PCRIndex parameter
passed from caller must be 0 to 23.
TPM2_MAX_PCRS is currently used to check the range of PCRIndex,
but TPM2_MAX_PCRS is tpm2 device dependent and may have larger value.
This commit newly adds EFI_TCG2_MAX_PCR_INDEX macro, it is used to
check the range of PCRIndex parameter.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
TCG EFI Protocol Specification defines the required parameter
checking and return value for each API.
This commit adds the missing parameter check and
fixes the wrong return value to comply the specification.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
When U-Boot is started we have to use the existing variables to determine
in which secure boot state we are.
* If a platform key PK is present and DeployedMode=1, we are in deployed
mode.
* If no platform key PK is present and AuditMode=1, we are in audit mode.
* Otherwise if a platform key is present, we are in user mode.
* Otherwise if no platform key is present, we are in setup mode.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Writing variables AuditMode and DeployedMode serves to switch between
Secure Boot modes. Provide a separate value for these in efi_auth_var_type.
With this patch the variables will not be read from from file even if they
are marked as non-volatile by mistake.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The UEFI specification requires that the signature database may only be
stored in tamper-resistant storage. So these variable may not be read
from an unsigned file.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
We should not first allocate memory and then report a rounded up value as
image size. Instead first round up according to section allocation and then
allocate the memory.
Fixes: 82786754b9 ("efi_loader: ImageSize must be multiple of SectionAlignment")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
In a section header VirtualSize may be zero. This is for instance seen in
the .sbat section of shim. In this case use SizeOfRawData as section size.
Fixes: 9d30a941cc ("efi_loader: don't load beyond VirtualSize")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Asherah Connor <ashe@kivikakk.ee>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
Memory allocated in the implementation of the
EFI_DEVICE_PATH_TO_TEXT_PROTOCOL must be of type EfiBootServicesData.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
dp_alloc() was using a constant from the wrong enum resulting in creating
device paths in EfiReservedMemory.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Use enum efi_memory_type and enum_allocate_type in the definitions of the
efi_allocate_pages(), efi_allocate_pool().
In the external UEFI API leave the type as int as the UEFI specification
explicitely requires that enums use a 32bit type.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Refactor efi_append_scrtm_version() to use common
function for adding eventlog and extending PCR.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
TCG PC Client PFP spec requires to measure
"Exit Boot Services Invocation" if ExitBootServices() is invoked.
Depending upon the return code from the ExitBootServices() call,
"Exit Boot Services Returned with Success" or "Exit Boot Services
Returned with Failure" is also measured.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Swap two ifs in efi_exit_boot_services().
efi_tcg2_notify_exit_boot_services must have EFIAPI signature.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
TCG PC Client PFP spec requires to measure "Boot####"
and "BootOrder" variables, EV_SEPARATOR event prior
to the Ready to Boot invocation.
Since u-boot does not implement Ready to Boot event,
these measurements are performed when efi_start_image() is called.
TCG spec also requires to measure "Calling EFI Application from
Boot Option" for each boot attempt, and "Returning from EFI
Application from Boot Option" if a boot device returns control
back to the Boot Manager.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
TCG PC Client PFP spec requires to measure the secure
boot policy before validating the UEFI image.
This commit adds the secure boot variable measurement
of "SecureBoot", "PK", "KEK", "db", "dbx", "dbt", and "dbr".
Note that this implementation assumes that secure boot
variables are pre-configured and not be set/updated in runtime.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
iPXE used Uri() device path nodes. So we should support them in the
device path to text protocol.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In the commit c982874e93 ("efi_loader: refactor
efi_setup_loaded_image()"), setjmp-related definitions were moved to
efi_loaded_image_obj in efi_loader.h. So setjmp.h is no longer
refererenced in efi_api.h.
This also fixes some error when efi_api.h will be included in
mkeficapsule.c.
Fixes: c982874e93 ("efi_loader: refactor efi_setup_loaded_image()")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If capsule authentication is disabled and yet a capsule file is signed,
its signature must be removed from image data to flush.
Otherwise, the firmware will be corrupted after update.
Fixes: 04be98bd6b ("efi: capsule: Add support for uefi capsule
authentication")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
efi_guid_capsule_root_cert_guid is never used.
Just remove it.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
SMBIOS tables only support 32bit addresses. If we don't have memory here
handle the error gracefully:
* on x86_64 fail to start U-Boot
* during UEFI booting ignore the missing table
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The capsule signature is now part of our DTB. This is problematic when a
user is allowed to change/fixup that DTB from U-Boots command line since he
can overwrite the signature as well.
So Instead of adding the key on the DTB, embed it in the u-boot binary it
self as part of it's .rodata. This assumes that the U-Boot binary we load
is authenticated by a previous boot stage loader.
Reviewed-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Tested-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
TCG PC Client PFP spec says "The Log Area Minimum Length
for the TCG event log MUST be at least 64KB." in ACPI chapter.
This commit increase the buffer size to 64KB.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Use %pD to log device-path instead of using efi_dp_str() and
efi_free_pool() locally in find_boot_device().
This is a cleanup patch, no feature update nor fix.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Previously, the GPT device GUID was being used instead of the partition,
which was incorrect.
Signed-off-by: Alfonso Sánchez-Beato <alfonso.sanchez-beato@canonical.com>
Let EFI_LOADER select CONFIG_PARTITION_UUIDS.
Use log_warning() instead of printf() for warning.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Fix find_boot_device() to set bootdev_root if it finds the
bootdev from BootNext. Currently it sets the bootdev_root only
when it finds bootdev from BootOrder.
Fixes: c74cd8bd08 ("efi_loader: capsule: add capsule_on_disk support")
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Accked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If multiple capsules are applied, the FMP drivers for the individual
capsules can expect the value of CapsuleLast to be accurate. Hence
CapsuleLast must be updated after each capsule.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
* Use log category LOGC_EFI. This allows to remove 'EFI:' prefixes in
messages.
* Rephrase some of the messages.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When reading a directory using EFI_FILE_PROTOCOL.Read() provide file
attributes and timestamps.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Although U-Boot supports capsule update on-disk, it's lack of support for
SetVariable at runtime prevents applications like fwupd from using it.
In order to perform the capsule update on-disk the spec says that the OS
must copy the capsule to the \EFI\UpdateCapsule directory and set a bit in
the OsIndications variable. The firmware then checks for the
EFI_OS_INDICATIONS_FILE_CAPSULE_DELIVERY_SUPPORTED bit in OsIndications
variable, which is set by the submitter to trigger processing of the
capsule on the next reboot.
Let's add a config option which ignores the bit and just relies on the
capsule being present. Since U-Boot deletes the capsule while processing
it, we won't end up applying it multiple times.
Note that this is allowed for all capsules. In the future, once
authenticated capsules are fully supported, we can limit the functionality
to those only.
Signed-off-by: apalos <ilias.apalodimas@linaro.org>
Reword Kconfig description.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
After each reboot we must clear flag
EFI_OS_INDICATIONS_FILE_CAPSULE_DELIVERY_SUPPORTED in variable
OsIndications.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Improve efi_query_variable_info() to check the parameter settings and
return correct error code according to the UEFI Specification 2.9,
and the Self Certification Test (SCT) II Case Specification, June
2017, chapter 4.1.4 QueryVariableInfo().
Reported-by: Kazuhiko Sakamoto <sakamoto.kazuhiko@socionext.com>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
After if we should use parentheses to keep the code readable.
Fixes: a95f4c8859 ("efi_loader: NULL dereference in EFI console")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We only install FMPs if a CapsuleUpdate is requested. Since we now have an
ESRT table which relies on FMPs to build the required information, it
makes more sense to unconditionally install them. This will allow userspace
applications (e.g fwupd) to make use of the ERST and provide us with files
we can use to run CapsuleUpdate on-disk
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Chapter 23 of the EFI spec (rev 2.9) says:
"A specific updatable hardware firmware store must be represented by
exactly one FMP instance".
This is not the case for us, since both of our FMP protocols can be
installed at the same time because they are controlled by a single
'dfu_alt_info' env variable.
So make the config options depend on each other and allow the user to
install one of them at any given time. If we fix the meta-data provided
by the 'dfu_alt_info' in the future, to hint about the capsule type
(fit or raw) we can revise this and enable both FMPs to be installed, as
long as they target different firmware hardware stores
Note that we are not using a Kconfig 'choice' on purpose, since we
want to allow both of those to be installed and tested in sandbox
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When running the efidebug capsule disk-update command, the efi_fmp_raw
protocol installation fails with 2 (EFI_INVALID_PARAMETER) as below.
This is because the code passes efi_root instead of the handle local var.
=> efidebug capsule disk-update
EFI: Call: efi_install_multiple_protocol_interfaces( &handle, &efi_guid_firmware_management_protocol, &efi_fmp_fit, NULL)
EFI: Entry efi_install_multiple_protocol_interfaces(00000000fbaf5988)
EFI: Call: efi_install_protocol_interface( handle, protocol, EFI_NATIVE_INTERFACE, protocol_interface)
EFI: Entry efi_install_protocol_interface(00000000fbaf5988, 86c77a67-0b97-4633-a187-49104d0685c7, 0, 00000000fbfa6ee8)
EFI: new handle 00000000fbb37520
EFI: Exit: efi_install_protocol_interface: 0
EFI: 0 returned by efi_install_protocol_interface( handle, protocol, EFI_NATIVE_INTERFACE, protocol_interface)
EFI: Exit: efi_install_multiple_protocol_interfaces: 0
EFI: 0 returned by efi_install_multiple_protocol_interfaces( &handle, &efi_guid_firmware_management_protocol, &efi_fmp_fit, NULL)
EFI: Call: efi_install_multiple_protocol_interfaces( &efi_root, &efi_guid_firmware_management_protocol, &efi_fmp_raw, NULL)
EFI: Entry efi_install_multiple_protocol_interfaces(00000000fbfec648)
EFI: Call: efi_install_protocol_interface( handle, protocol, EFI_NATIVE_INTERFACE, protocol_interface)
EFI: Entry efi_install_protocol_interface(00000000fbfec648, 86c77a67-0b97-4633-a187-49104d0685c7, 0, 00000000fbfa6f18)
EFI: handle 00000000fbaf8520
EFI: Exit: efi_install_protocol_interface: 2
EFI: 2 returned by efi_install_protocol_interface( handle, protocol, EFI_NATIVE_INTERFACE, protocol_interface)
EFI: Exit: efi_install_multiple_protocol_interfaces: 2
EFI: 2 returned by efi_install_multiple_protocol_interfaces( &efi_root, &efi_guid_firmware_management_protocol, &efi_fmp_raw, NULL)
Command failed, result=1
To fix this issue, pass the handle local var which is set NULL right
before installing efi_fmp_raw as same as the installing efi_fmp_fit.
(In both cases, the local reference to the handle will be just discarded)
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
According to chapter 7.1 "Event, Timer, and Task Priority Services"
TPL_HIGH_LEVEL should not be exposed to applications and drivers.
According to the discussion with EDK II contributors this implies that
CreateEvent() shall not allow to create events with TPL_HIGH_LEVEL.
Cc: Samer El-Haj-Mahmoud <Samer.El-Haj-Mahmoud@arm.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Samer El-Haj-Mahmoud <Samer.El-Haj-Mahmoud@arm.com>
Brackets '[' need to be escaped to avoid a build warning
lib/efi_loader/efi_image_loader.c:223:
WARNING: Inline strong start-string without end-string.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Masahisa Kojima <masahisa.kojima@linaro.org>
If we want to address partition 15 of virtio block device 11, we have to
write:
virtio b:f
When calling sprintf() we must use %x for the device and partition numbers.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
"TCG PC Client Platform Firmware Profile Specification"
requires to measure every attempt to load and execute
a OS Loader(a UEFI application) into PCR[4].
This commit adds the PE/COFF image measurement, extends PCR,
and appends measurement into Event Log.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Replace CONFIG_HASH_CALCULATE by CONFIG_HASH
Fix conversions between pointers and u64.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The hash_calculate() symbol is provided by hash-checksum.c. It depends
on hash_progressive_lookup_algo(), provided when CONFIG_HASH=y.
The issue is that hash_calculate() is used by the efi_loader,
irregardless of CONFIG_FIT_SIGNATURE. As pointed out in
commit 87316da05f ("lib: introduce HASH_CALCULATE option"),
enabling hash_calculate() based on CONFIG_FIT_SIGNATURE is incorrect.
To resolve this, use CONFIG_HASH as the compile switch for
hash-checksum.c. This ensures that all dependencies are compiled, and
is the most natural Kconfig to use.
There is the issue of having to 'select HASH' in a couple of places
that already 'select SHA256'. This is a deeper problem with how hashes
are organized, and fixing it is beyonf the scope of this change.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Masahisa Kojima <masahisa.kojima@linaro.org>
When we think of Kconfig, we usually think of features that we like
to enable or not. Ideally, we wouldn't use Kconfig to fix a build
issue, although sometimes it might make sense. With Kconfig it's hard
to guarantee that the fix is universal. We can only say that it works
for the set of tested configurations. In the majority of cases, it's
preferable to let the linker figure things out for us.
The reverted commit attempted to fix a build issue by adding an
invisible Kconfig option. This is wrong in several ways:
It invents a new Kconfig variable when CONFIG_HASH already
exists for the same purpose.
Second, hash-checksum.c makes use of the hash_progressive_lookup_algo()
symbol, which is only provided with CONFIG_HASH, but this dependency
was not expressed in the reverted patch.
It feels like Kconfig is turning into a listing of all available
source files, and a buffet to 'select' which ones to compile. The
purpose of this revert is to enable the next change to make use of
CONFIG_HASH instead of adding to Kconfig.
This reverts commit 87316da05f.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Coverity reported 3 warnings on the current code.
CID 331856, 331855, 331854 on the latest scan.
Fix the rest of the warnings by initializing the variables before
passing them to tpm2_get_pcr_info().
In order to avoid future warnings and errors initialize them to 0 within
the function as well, since the values are always OR'ed after querying the
hardware.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Compiling with -Wextra produces a number of (harmless) warnings for the EFI
TCG2 protocol. Let's fix those in case we ever enable the flag on the EFI
subsystem
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Before this patch efi_dp_from_name() only accommodated a maximum file path
length of 31 characters. This leads to boot failures due to file name
truncation.
Allow arbitrary path lengths.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is preparation for PE/COFF measurement support.
PE/COFF image hash calculation is same in both
UEFI Secure Boot image verification and measurement in
measured boot. PE/COFF image parsing functions are
gathered into efi_image_loader.c, and exposed even if
UEFI Secure Boot is not enabled.
This commit also adds the EFI_SIGNATURE_SUPPORT option
to decide if efi_signature.c shall be compiled.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Configuring a system with CONFIG_EFI_CAPSULE_AUTHENTICATE=y but without a
method to retrieve the public key data is a misconfiguration. We should get
a build failure for it. Therefore remove the weak efi_get_public_key_data()
implementation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Build error occurs when CONFIG_EFI_SECURE_BOOT or
CONFIG_EFI_CAPSULE_AUTHENTICATE is enabled,
because hash-checksum.c is not compiled.
Since hash_calculate() implemented in hash-checksum.c can be
commonly used aside from FIT image signature verification,
this commit itroduces HASH_CALCULATE option to decide
if hash-checksum.c shall be compiled.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
EFI_TCG2 depends not only on TPMv2 but also on the underlying algorithms.
So select the missing SHA1, SHA256, SHA384 and SHA512 we currently support
Reported-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add 'default y'.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Up to now we are stopping the EFI subsystem if a TPMv2 exists but the
protocol fails to install. Now that we've switched the config to 'default
y' the sandbox TPM fails, since it doesn't support all the required
capabilities of the protocol.
Not installing the protocol is not catastrophic. If the protocol fails
to install the PCRs will never be extended to the expected values, so
some other entity later in the boot flow will eventually figure it out
and take the necessary actions.
While at it fix a corner case were the user can see an invalid error
message when the protocol failed to install. We do have a tcg2_uninit()
which we call when the protocol installation fails. There are cases though
that this might be called before the configuration table is installed (e.g
probing the TPM for capabilities failed). In that case the user will see
"Failed to delete final events config table". So stop printing it since it's
not an actual failure , simply because the config table was never installed
in the first place.
In order to stop printing it make efi_init_event_log() and create_final_event()
cleanup themselves and only call tcg2_uninit() when the protocol installation
fails.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Instead of just failing, clean up the installed config table and
EventLog memory if logging an s-crtm event fails during the protocol
installation
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Eliminate label 'out:' by using return.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
efi_init_event_log() calls tcg2_uninit() in case of failure.
We can skip that since the function is called on efi_tcg2_register()
which also cleans up if an error occurs
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is same issue as https://bugzilla.redhat.com/show_bug.cgi?id=1733817,
but that fix was wrongly partial reverted.
When reading a directory, EFI_BUFFER_TOO_SMALL should be returned when
the supplied buffer is too small, so a use-case is to call
EFI_FILE_PROTOCOL.Read() with *buffer_size=0 and buffer=NULL to
obtain the needed size before doing the actual read.
So remove the check only for directory reading, file reading already
do the check by itself.
Fixes: db12f518edb0("efi_loader: implement non-blocking file services")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefan Sørensen <stefan.sorensen@spectralink.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The current capsule authentication code checks if the environment
variable capsule_authentication_enabled is set, for authenticating the
capsule. This is in addition to the check for the config symbol
CONFIG_EFI_CAPSULE_AUTHENTICATE. Remove the check for the environment
variable. The capsule will now be authenticated if the config symbol
is set.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviwed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Building 32bit boards with the TCG2 protocol enabled leads to a build
warning due to a missing conversion.
lib/efi_loader/efi_tcg2.c:774:27:
error: cast to pointer from integer of different size
[-Werror=int-to-pointer-cast]
774 | ret = tcg2_create_digest((u8 *)data_to_hash, data_to_hash_len,
| ^
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
In case of failure at efi_get_variable_int("BootOrder"), we should
skip examining boot option variables and return an appropriate error
code which is the one the function returned.
Fixes: CID 331153 Code maintainability issues (UNUSED_VALUE)
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Indicated by Coverity Scan CID 331147
The ESRT was being refreshed in situations where the UpdateCapsule
procedure failed. In that scenario:
1) the ESRT refresh was superfluous.
2) a failed ESRT refresh return code overwrites the UpdateCapsule error
return code.
This commit ensures that the ESRT is only refreshed when the
UpdateCapsule performs successfully.
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Sughosh Ganu <sughosh.ganu@linaro.org>
CC: AKASHI Takahiro <takahiro.akashi@linaro.org>
CC: Tom Rini <trini@konsulko.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: nd@arm.com
Signed-off-by: Jose Marinho <jose.marinho@arm.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Bumping the digest list count, for all supported algorithms, can be
calculated outside of the individual switch statements. So let's do that
for every loop iteration instead and simplify the code a bit.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
To avoid diverging function definitions we need to include efi_loader.h.
Fixes: fe179d7fb5 ("efi_loader: Add size checks to efi_create_indexed_name()")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Variable "final" will have SHA512 digest, but currently
the array size is not sufficient. Let's fix it.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If realloc() fails, we should free the old buffer.
Fixes: c74cd8bd08: ("efi_loader: capsule: add capsule_on_disk support")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Remove function invocations using the EFI_CALL macro for those
functions that do not have an EFI_ENTRY call in their definition. Such
functions can use u-boot api's which rely on u-boot global data(gd)
pointer. The Arm and RiscV architectures maintain a separate gd
pointer, one for u-boot, and a separate gd for the efi application.
Calling a function through the EFI_CALL macro changes the gd pointer
to that used for the efi application, with u-boot gd being
unavailable. Any function then trying to dereference u-boot's gd will
result in an abort.
Fix this issue by removing the EFI_CALL macro for all of such
functions which do not begin by an EFI_ENTRY function call.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Although ptr arithmetics are allowed with extensions in gcc, they
are not allowed by the C spec. So switch to (void *)(uintptr_t) instead
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Fix the build warning when building for 32 bit systems by using the
length modifier for size_t.
lib/efi_loader/efi_esrt.c: In function ‘efi_esrt_populate’:
include/efi_loader.h:126:8: warning: format ‘%ld’ expects argument of type ‘long int’, but argument 8 has type ‘size_t’ {aka ‘unsigned int’} [-Wformat=]
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable building of the crypto helper functions used during capsule
authentication by selecting IMAGE_SIGN_INFO.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
get_var() is defined statically in efi_bootmgr.c and doesn't properly
check a buffer allocation. Remove it completely and use the exported
function from efi_var_common.c that does the same thing
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In the devicepath node to text conversion for Uart nodes a break statement
is missing.
Indicated by Coverity Scan CID 330038
Fixes: 62df6e9c99 ("efi_loader: Uart device path")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We recently added a common function for calculating file size,
instead of copy pasting the code around. Switch one of the
occurences over to the common function
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviwed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
TCG PC Client Platform Firmware Profile Spec mandates that an S-CRTM
event for the version identifier using the event type EV_S_CRTM_VERSION
must be measured.
So since we are trying to add more conformance into U-Boot, let's add
the event using U_BOOT_VERSION_STRING, extend PCR[0] accordingly and log
it in the EventLog
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Current code doesn't free the efi allocated memory in case the protocol
failed to install
Fixes: c8d0fd5825 ("efi_loader: Introduce eventlog support for TCG2_PROTOCOL")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The ESRT is initialised during efi_init_objlist after
efi_initialize_system_table().
The ESRT is recreated from scratch at the following events:
- successful UpdateCapsule;
- FMP instance install.
The code ensures that every ESRT entry has a unique fw_class value.
Limitations:
- The ESRT is not updated if an FMP instance is uninstalled;
- the fields image_type and flags are in the current implementation left
undefined. Setting these values will require a per-platform function
that returns the image_type/flags as a function of the image fw_class.
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Sughosh Ganu <sughosh.ganu@linaro.org>
CC: AKASHI Takahiro <takahiro.akashi@linaro.org>
CC: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CC: Andre Przywara <andre.przywara@arm.com>
CC: Alexander Graf <agraf@csgraf.de>
CC: nd@arm.com
Signed-off-by: Jose Marinho <jose.marinho@arm.com>
Remove two EFI_CALL() indirections.
Move ESRT GUID in efidebug's list of GUIDs.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Up to now we install EFI_LOAD_FILE2_PROTOCOL to load an initrd
unconditionally. Although we correctly return various EFI exit codes
depending on the file status (i.e EFI_NO_MEDIA, EFI_NOT_FOUND etc), the
kernel loader, only falls back to the cmdline interpreted initrd if the
protocol is not installed.
This creates a problem for EFI installers, since they won't be able to
load their own initrd and continue the installation. It also makes the
feature hard to use, since we can either have a single initrd or we have
to recompile u-boot if the filename changes.
So let's introduce a different logic that will decouple the initrd
path from the config option we currently have.
When defining a UEFI BootXXXX we can use the filepathlist and store
a file path pointing to our initrd. Specifically the EFI spec describes:
"The first element of the array is a device path that describes the device
and location of the Image for this load option. Other device paths may
optionally exist in the FilePathList, but their usage is OSV specific"
When the EFI application is launched through the bootmgr, we'll try to
interpret the extra device path. If that points to a file that exists on
our disk, we'll now install the load_file2 and the efi-stub will be able
to use it.
This opens up another path using U-Boot and defines a new boot flow.
A user will be able to control the kernel/initrd pairs without explicit
cmdline args or GRUB.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
A following patch introduces a different logic for loading initrd's
based on the EFI_LOAD_FILE2_PROTOCOL.
Since similar logic can be applied in the future for other system files
(i.e DTBs), let's add some helper functions which will retrieve and
parse file paths stored in EFI variables.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
On the following patches we allow for an initrd path to be stored in
Boot#### variables. Specifically we encode in the FIlePathList[] of
the EFI_LOAD_OPTIONS for each Boot#### variable.
The FilePathList[] array looks like this:
kernel - 0xff - VenMedia(initrd GUID) - initrd1 - 0x01 initrd2 - 0xff
So let's add the relevant functions to concatenate and retrieve a device
path based on a Vendor GUID.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reformat function descriptions.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When uploading an EFI binary via the UART we need to assign a device path.
* Provide devicepath node to text conversion for Uart() node.
* Provide function to create Uart() device path.
* Add UART support to efi_dp_from_name().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Even if CONFIG_DM_VIDEO=y and stdout="vidconsole", a video device may not
be available. Check the return values of the relevant functions.
If no video output device is available, assume that the serial console is
in use.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This occur when building on Raspberry Pi 400 (32-bit ARM). Fix them.
Examples:
cmd/efidebug.c: In function ‘do_efi_capsule_update’:
cmd/efidebug.c:75:49: warning: cast from pointer to integer of different
size [-Wpointer-to-int-cast]
ret = EFI_CALL(RT->update_capsule(&capsule, 1, (u64)NULL));
^
include/efi_loader.h:104:9: note: in definition of macro ‘EFI_CALL’
typeof(exp) _r = exp; \
^~~
cmd/efidebug.c:75:49: warning: cast from pointer to integer of different
size [-Wpointer-to-int-cast]
ret = EFI_CALL(RT->update_capsule(&capsule, 1, (u64)NULL));
^
include/efi_loader.h:104:19: note: in definition of macro ‘EFI_CALL’
typeof(exp) _r = exp; \
^~~
In file included from include/common.h:20,
from lib/efi_loader/efi_capsule.c:9:
lib/efi_loader/efi_capsule.c: In function ‘efi_update_capsule’:
include/efi_loader.h:83:8: warning: format ‘%lu’ expects argument of type
‘long unsigned int’, but argument 10 has type ‘size_t’
{aka ‘unsigned int’} [-Wformat=]
debug("%sEFI: Entry %s(" format ")\n", __efi_nesting_inc(), \
^~~~~~~~~~~~~~~~~~
include/linux/printk.h:37:21: note: in definition of macro ‘pr_fmt’
#define pr_fmt(fmt) fmt
^~~
include/log.h:229:2: note: in expansion of macro ‘log’
log(LOG_CATEGORY, LOGL_DEBUG, fmt, ##args); \
^~~
include/log.h:249:2: note: in expansion of macro ‘debug_cond’
debug_cond(_DEBUG, fmt, ##args)
^~~~~~~~~~
include/efi_loader.h:83:2: note: in expansion of macro ‘debug’
debug("%sEFI: Entry %s(" format ")\n", __efi_nesting_inc(), \
^~~~~
lib/efi_loader/efi_capsule.c:444:2: note: in expansion of macro ‘EFI_ENTRY’
EFI_ENTRY("%p, %lu, %llu\n", capsule_header_array, capsule_count,
^~~~~~~~~
lib/efi_loader/efi_capsule.c:444:19: note: format string is defined here
EFI_ENTRY("%p, %lu, %llu\n", capsule_header_array, capsule_count,
~~^
%u
Signed-off-by: Simon Glass <sjg@chromium.org>
Replace (uintptr_t)NULL by 0.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The (yet unreleased version of the) devicetree specification clearly
states that:
As with the /reserved-memory node, when booting via UEFI
entries in the Memory Reservation Block must also be listed
in the system memory map obtained via the GetMemoryMap() toi
protect against allocations by UEFI applications. The memory
reservation block entries should be listed with type
EfiReservedMemoryType.
This restores the behaviour that was changed by commit 4cbb2930bd
("efi_loader: consider no-map property of reserved memory").
Fixes: 4cbb2930bd ("efi_loader: consider no-map property of reserved memory")
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
GRUB_ARM32_WORKAROUND can be disabled on ARCH_SUNXI as the Allwinner SoCs
only have a level 2 cache controlled via CP15 and not an architecturally
defined cache. Having the cache available speeds up booting Linux.
On ARCH_BCM283X it is already disabled via rpi_2_defconfig. But let's move
this setting to Kconfig.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When uploading an EFI binary via the UART we need to assign a device path.
* Provide devicepath node to text conversion for Uart() node.
* Provide function to create Uart() device path.
* Add UART support to efi_dp_from_name().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Even if CONFIG_DM_VIDEO=y and stdout="vidconsole", a video device may not
be available. Check the return values of the relevant functions.
If no video output device is available, assume that the serial console is
in use.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This occur when building on Raspberry Pi 400 (32-bit ARM). Fix them.
Examples:
cmd/efidebug.c: In function ‘do_efi_capsule_update’:
cmd/efidebug.c:75:49: warning: cast from pointer to integer of different
size [-Wpointer-to-int-cast]
ret = EFI_CALL(RT->update_capsule(&capsule, 1, (u64)NULL));
^
include/efi_loader.h:104:9: note: in definition of macro ‘EFI_CALL’
typeof(exp) _r = exp; \
^~~
cmd/efidebug.c:75:49: warning: cast from pointer to integer of different
size [-Wpointer-to-int-cast]
ret = EFI_CALL(RT->update_capsule(&capsule, 1, (u64)NULL));
^
include/efi_loader.h:104:19: note: in definition of macro ‘EFI_CALL’
typeof(exp) _r = exp; \
^~~
In file included from include/common.h:20,
from lib/efi_loader/efi_capsule.c:9:
lib/efi_loader/efi_capsule.c: In function ‘efi_update_capsule’:
include/efi_loader.h:83:8: warning: format ‘%lu’ expects argument of type
‘long unsigned int’, but argument 10 has type ‘size_t’
{aka ‘unsigned int’} [-Wformat=]
debug("%sEFI: Entry %s(" format ")\n", __efi_nesting_inc(), \
^~~~~~~~~~~~~~~~~~
include/linux/printk.h:37:21: note: in definition of macro ‘pr_fmt’
#define pr_fmt(fmt) fmt
^~~
include/log.h:229:2: note: in expansion of macro ‘log’
log(LOG_CATEGORY, LOGL_DEBUG, fmt, ##args); \
^~~
include/log.h:249:2: note: in expansion of macro ‘debug_cond’
debug_cond(_DEBUG, fmt, ##args)
^~~~~~~~~~
include/efi_loader.h:83:2: note: in expansion of macro ‘debug’
debug("%sEFI: Entry %s(" format ")\n", __efi_nesting_inc(), \
^~~~~
lib/efi_loader/efi_capsule.c:444:2: note: in expansion of macro ‘EFI_ENTRY’
EFI_ENTRY("%p, %lu, %llu\n", capsule_header_array, capsule_count,
^~~~~~~~~
lib/efi_loader/efi_capsule.c:444:19: note: format string is defined here
EFI_ENTRY("%p, %lu, %llu\n", capsule_header_array, capsule_count,
~~^
%u
Signed-off-by: Simon Glass <sjg@chromium.org>
Replace (uintptr_t)NULL by 0.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The (yet unreleased version of the) devicetree specification clearly
states that:
As with the /reserved-memory node, when booting via UEFI
entries in the Memory Reservation Block must also be listed
in the system memory map obtained via the GetMemoryMap() toi
protect against allocations by UEFI applications. The memory
reservation block entries should be listed with type
EfiReservedMemoryType.
This restores the behaviour that was changed by commit 4cbb2930bd
("efi_loader: consider no-map property of reserved memory").
Fixes: 4cbb2930bd ("efi_loader: consider no-map property of reserved memory")
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
GRUB_ARM32_WORKAROUND can be disabled on ARCH_SUNXI as the Allwinner SoCs
only have a level 2 cache controlled via CP15 and not an architecturally
defined cache. Having the cache available speeds up booting Linux.
On ARCH_BCM283X it is already disabled via rpi_2_defconfig. But let's move
this setting to Kconfig.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Carve out a function to translate a Unicode code point to an 8bit codepage.
Provide a unit test for the new function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If stdout is 'vidconsole', we correctly set the console size.
If stdout is 'vidconsole,serial', the video console is ignored.
We should always evaluate the size of vidconsole if it is the primary
console.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
VenHw and VenMedia device path nodes may carry vendor defined data of
arbitrary length. When converting a device path node to text ensure that we
do not overrun our internal buffer.
In our implementation of
EFI_DEVICE_PATH_TO_TEXT_PROTOCOL.ConvertDevicePathToText() we could first
determine the output length and then allocate buffers but that would nearly
double the code size. Therefore keep the preallocated buffers and truncate
excessive device paths instead.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
