This platform is unsupported by TI and was never widely distributed. As
this is untested for a long while and missing some DM conversions,
remove it and related device tree files.
Signed-off-by: Tom Rini <trini@konsulko.com>
Errata doc: https://www.ti.com/lit/pdf/sprz457
Errata ID i2331 CPSW: Device lockup when reading CPSW registers
Details: A device lockup can occur during the second read of any CPSW
subsystem register after any MAIN domain power on reset (POR). A MAIN
domain POR occurs using the hardware MCU_PORz signal, or via software
using CTRLMMR_RST_CTRL.SW_MAIN_POR or CTRLMMR_MCU_RST_CTRL.SW_MAIN_POR.
After these resets, the processor and internal bus structures may get
into a state which is only recoverable with full device reset using
MCU_PORz.
Due to this errata, Ethernet boot should not be used on this device.
Workaround(s): To avoid the lockup, a warm reset should be issued after
a MAIN domain POR and before any access to the CPSW registers. The warm
reset realigns internal clocks and prevents the lockup from happening.
Workaround above errata by calling do_reset() in case of cold boot in
order to trigger warm reset. This needs enabling SYSRESET driver in R5
SPL to enable TI SCI reset driver.
Signed-off-by: Nitin Yadav <n-yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Add support to detect daughtercards (GESI Ethernet card) in-order
to set the MAC address of the main CPSW2G interface.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Update the default BOOTCOMMAND to provide an automatic and easier way
to configure ethernet PHY before loading the firmware.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Add board specific devicetree for Bananapi R3 SBC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Commit dafe0fbfb0 ("pinctrl: mediatek: rewrite mtk_pinconf_set and
related functions") changed the logic deciding to set R0 and R1
registers for V1 devices.
Before:
/* Also set PUPD/R0/R1 if the pin has them */
err = mtk_hw_set_value(dev, pin, PINCTRL_PIN_REG_PUPD, !pullup);
if (err != -EINVAL) {
mtk_hw_set_value(dev, pin, PINCTRL_PIN_REG_R0, r0);
mtk_hw_set_value(dev, pin, PINCTRL_PIN_REG_R1, r1);
}
After:
/* try pupd_r1_r0 if pullen_pullsel return error */
err = mtk_pinconf_bias_set_pullen_pullsel(dev, pin, disable, pullup,
val);
if (err)
return mtk_pinconf_bias_set_pupd_r1_r0(dev, pin, disable,
pullup, val);
Tracing mtk_pinconf_bias_set_pullen_pullsel shows that the function
always either returns 0 in case of success or -EINVAL in case any error
has occurred. Hence the logic responsible of the decision to program R0
and R1 has been inverted.
This leads to problems on BananaPi R2 (MT7623N) when booting from
SDMMC, it turns out accessing eMMC no longer works since
U-Boot 2022.07:
MT7623> mmc dev 0
Card did not respond to voltage select! : -110
The problem wasn't detected for a long time as both eMMC and SDMMC work
fine if they are used to boot from, and hence R0 and R1 were already
setup by the bootrom and/or preloader.
Fix the logic to restore the originally intended and correct behavior
and also change the descriptive comment accordingly.
Fixes: dafe0fbfb0 ("pinctrl: mediatek: rewrite mtk_pinconf_set and related functions")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Enable Quality of Service (QoS) blocks for Display SubSystem (DSS), by
servicing the DSS - DDR traffic from the Real-Time (RT) queue. This is
done by setting the DSS DMA orderID to 8.
The C7x and VPAC have been overwhelming the DSS's access to the DDR
(when it was accessing via the Non Real-Time (NRT) Queue), primarily
because their functional frequencies, and hence DDR accesses, were
significantly higher than that of DSS. This led the display to flicker
when certain edgeAI models were being run.
With the DSS traffic serviced from the RT queue, the flickering issue
has been found to be mitigated.
The am62a qos files are auto generated from the k3 resource partitioning
tool.
Section-3.1.12, "QoS Programming Guide", in the AM62A TRM[1], provides
more information about the QoS, and section-14.1, "System Interconnect
Registers", provides the register descriptions.
[1] AM62A Tech Ref Manual: https://www.ti.com/lit/pdf/spruj16
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
J721E and J7200 have same file j721e_init.c which had the firewall
configs for J721E being applied on J7200 causing the warnings. Split the
firewalls for both the boards to remove those warnings.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The current documentation for Snapdragon based Samsung
and Qualcomm boards is vague in the sense that at one place
it mentions that u-boot can be used as a replacement for ABL
bootloader and at another it mentions that u-boot is loaded
as an Android boot image through ABL.
Fix the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Currently a few 'board/qualcomm/../Makefile' point to incorrect
path of sdm845 board file.
Fix the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
K3 devices have some firewalls set up by ROM that we usually remove so
that the development is easy in HS devices.
While removing the firewalls disabling a background region before
disabling the foreground regions keeps the firewall in a state where all
the transactions will be blacklisted until all the regions are disabled.
This causes a race for some other entity trying to access that memory
region before all the firewalls are disabled and causes an exception.
Since the background regions configured by ROM are in such a manner
that they allow all transactions, don't touch the background regions at
all.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
Allow non fitImage bootflow on Field Securable (HS-FS) devices in
addition to GP, force fitImage boot only on Security enforced (HS-SE)
devices where signed images are necessary to maintain chain of trust.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
On modern Qualcomm platforms including SDM845 a GENI SE QUP IP
description is supposed to be found in board device tree nodes,
the version of the IP is used by the GENI UART driver to properly
set an oversampling divider value, which impacts UART baudrate.
The change touches dragonboard845c and starqltechn board device
tree source files, a device tree node label to "debug" UART is
renamed to 'uart9' according to the naming found in Linux.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Starting from QUP v2.5 the value of oversampling is changed from 32
to 16, keeping the old value on newer platforms results on wrong set
UART IP clock divider, thus the asked baudrate does not correspond to
the actually set with all the consequencies for a user.
The change links the driver to a new Qualcomm GENI SE QUP driver
to get its hardware version and update the oversampling value.
Deliberately the code under CONFIG_DEBUG_UART_MSM_GENI is not touched,
since a wanted baudrate can be controlled by setting a modified
CONFIG_DEBUG_UART_CLOCK build time variable.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
The name "se" is used in upstream Linux device trees and has been for
ages, long before this U-Boot-ism was introduced. Same goes for the
existing compatible. Get rid of that.
[vzapolskiy: removed a ready change in the driver]
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
A compiler warns about a missing function prototype, which is valid
and fixed by converting the function into static one, also fix
interleaved local variable declarations and assignments.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Fixes: 324df15a29 ("serial: qcom: add support for GENI serial driver")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
This a cosmetic change, which corrects code indentation in a few places.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
There is only one clock supplier to the serial IP, thus getting it by
name is not needed, also note that "clock-names" property is not listed
under doc/device-tree-bindings/serial/msm-geni-serial.txt, and finally
"se-clk" clock name is invalid, if added, it shall get "se" value like
it's already described in Linux device tree documentation.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
In preparation for supporting upstream Linux device trees on Qualcomm
platforms, make this the default behavior.
[vzapolskiy: extracted the driver change from a combination with dts changes]
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
For whatever reason, likely a driver stub was copied from another
driver, the driver contains a bunch of unnecessary and confusing
includes like watchdog.h etc., the change reduces the list.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
This change adds a Qualcomm GENI SE QUP device driver as a wrapper for
actually enabled and used serial devices found on a board.
At the moment the driver is pretty simple, its intention is to populate
childred devices and provide I/O mem read interface to them as clients,
this is needed for GENI UART driver to set up a proper clock divider
and provide the actually asked baud rate.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
This adds a simple Northstar "BRCMNS" board to be used with
the BCM4708x and BCM5301x chips.
The main intention is to use this with the D-Link DIR-890L
and DIR-885L routers for loading the kernel into RAM from
NAND memory using the BCH-1 ECC and using the separately
submitted SEAMA load command, so we are currently not adding
support for things such as networking.
The DTS file is a multiplatform NorthStar board, designed to
be usable with several NorthStar designs by avoiding any
particulars not related to the operation of U-Boot.
If other board need other ECC for example, they need to
create a separate DTS file and augment the code, but I don't
know if any other users will turn up.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The original Northstar is an ARM SoC series that comprise
BCM4709x and BCM5301x and uses a dual-core Cortex A9, the
global timer and a few other things.
This series should not be confused with North Star Plus
(NSP) which is partly supported by U-Boot already.
The SoC is well supported by the Linux kernel and OpenWrt
as it is used in many routers.
Since we currently don't need any chip-specific quirks
and can get the system up from just the device tree, a
mach-* directory doesn't even need to be added, just
some small Kconfig fragments.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This brings in the main SoC device tree used by the
Broadcom Northstar chipset, i.e. BCM4709x and BCM5301x.
This is taken from the v6.3 Linux kernel.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MAX14526 is a powerful extcon chip which allows detection of various
plugs like usb, mhl, uart, headset etc. This version of driver
implements support of AP-usb and CP-usb/uart paths.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # LG P880 T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new simple uclass for extcon. Currently all setup is done
in the probe. Uclass struct and ops are empty for now.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PCI autoconfig case for PCI_CLASS_PROCESSOR_POWERPC just prints debug
message and then calls autoconfig setup code like for any other standard
endpoint device. We do not need special debug message for it, so remove
this case and handle PCI_CLASS_PROCESSOR_POWERPC via default code path.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The files include/tpm* are an integral part of the TPM drivers.
The tpm* commands are used to access TPM devices.
Both should be managed by the TPM DRIVERS maintainer.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
At BDF address 00:00.0 is fictional device which PCI configuration header
is for configuring mpc85xx PCI controller itself. PCI config space of this
device has ATMU inbound registers on position of PCI BARs. Trying to do PCI
auto configuration of this device cause rewriting ATMU inbound registers.
To avoid it, do not allow overwriting registers at BARs positions. And
because this device does not have any PCI memory, return zeros when trying
to read PCI BARs config space registers. It signals to auto configuration
tool to not allocate any PCI memory for this device.
This information is taken from MPC8544E Reference Manual, sections
17.3.1.3, 17.3.1.1.1, 17.3.2 and 17.3.2.11. Available at NXP website:
https://www.nxp.com/docs/en/reference-manual/MPC8544ERM.pdf
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Driver pci_mpc85xx.c is PCI controller driver for old PCI Local Bus,
which does not support access to extended PCIe registers (above 0xff),
as opposite of the PCIe driver pcie_fsl.c for the same platform.
So do not try to access extended PCIe registers as it cannot work.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
This Freescale mpc85xx PCI controller should support 8-bit and 16-bit read
and write access to PCI config space as described in more Freescale
reference manuals.
This change fixes issue that 8-bit and 16-bit write to PCI config space
caused to clear adjacent bits of 32-bit PCI register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
On PowerPC we should use barrier after store operation to HW register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
The "Programming Environments Manual for 32-Bit Implementations of the
PowerPC™ Architecture" says "W and G bits are not defined for IBAT
registers. Attempting to write to these bits causes boundedly-undefined
results"
The "e300 Power Architecture™ Core Family Reference Manual" says the
same: "Neither the W or G bits of the IBAT registers should be set.
Attempting to write to these bits causes boundedly-undefined results."
Remove the possibility to set those bytes.
Fixes: 30915ab95d ("mpc83xx: Migrate BATS config to Kconfig")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Mario Six <mario.six@gdsys.cc>
Please pull the second part of the sunxi pull request for this cycle.
Another bunch of patches that replace old-school U-Boot hacks with
proper DM based code, this time for the raw NAND flash driver, and the
USB PHY VBUS detection code. Plus two smaller patches that were sitting
in my inbox for a while.
Gitlab CI passed. In lack of some supported board with NAND flash I
couldn't really test this part, but apparently this was tested by the
reviewer. I briefly ran the branch on some boards with USB-OTG, and
this still worked.
This pull request adds support for the last CPU board from
CS GROUP France (previously CSSI).
That CPU board called CMPCPRO has a mpc8321E CPU (Family PQII PRO hence
its name) and can be plugged in place of the CMPC885 board.
In order to support that new board, the following changes are included
in this series:
- Make the mpc8xx watchdog driver more generic for reusing it
with mpc83xx
- Fix various small problems on mpc83xx platform
- Add a GPIO Driver for QE GPIOs
- Add support for mpc832x into mpc83xx SPI driver
- Refactor existing board code that will be shared with new board
- Add the new board
various other minor fixes
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmRMHUARHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZYvQf/R868tRhADWw5UfUyg4TdSWsfGmNlmnYT
eU2e4L1riWvTzrQh30CGhXOamsgfrsDfOdERgypl1bRvhwI68GZPqjXXAyEcIcsP
HkqU47cUv4998Gcg4WwWdImU1vBeY1TRckgk3ILGMM1f4yGIlEaA/iYK8sqP2VuO
UYbrTVBPs5bu7BCQuLyMsR9SKpgMr8CTx9/UqBZioeXwwm8PD5+6S4kh8OlwWn93
5uFxxgFHSDioZZvM2A4sHkpsR5AxPJbC+Jxy9VHdMpfEaHk1E9H28gQnbnnDvByz
7I1JWVBeH/xu/OLjG9OR97s/yZF7IpcNtld+EMhczx1JJoxwxDBAKg==
=G7yK
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-28apr23' of https://source.denx.de/u-boot/custodians/u-boot-dm
sandbox and fdt bug fixes / tweaks
various other minor fixes
For the devfdt_get_addr_index_ptr() and devfdt_get_addr_size_index_ptr()
function use map_sysmem() function as cast for the return for use in
sandbox. Also fix sandbox test.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drop second hunk:
Signed-off-by: Simon Glass <sjg@chromium.org>
importlib.resources became part of 3.7 only. Allow using distros with
3.6 and the importlib_resources backport.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drop the map_to_sysmem() copy paste error. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
