Move these two options to the arch Kconfig file.
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
The correct mask for getting the source/destination register from ESR in
the case of an unaligned access exception is 0x3E0. With this change, a
dummy unaligned store produces the expected info:
"""
>> swi r5, r0, 0x111
...
Hardware exception at 0x111 address
Unaligned data access exception
Unaligned word access
Unaligned store access
Register R5
Return address from exception 0x7f99dfc
### ERROR ### Please RESET the board ###
"""
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20220213080925.1548411-6-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The unaligned access messages are only valid in the case of an unaligned
data access exception. Do not print them for other types of hw exceptions.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20220213080925.1548411-5-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
According to the MicroBlaze reference manual (xilinx2021.2/ug984/page-37):
"""
If an exception is caused by an instruction in a delay slot (that is,
ESR[DS]=1), the exception handler should return execution to
the address stored in BTR instead of the normal exception return
address stored in R17.
"""
Adjust the code to print the proper return address for delay slot
exceptions.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20220213080925.1548411-4-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The switch statement in _hw_exception_handler() only covers the
rightmost 5 bits that encode the exception cause:
switch (state & 0x1f)
{
...
}
For this reason, the "0x1000" case will never be reached, because the 13th
bit was zeroed out. To fix this, move delay slot exception handling before
the switch statement (delay slot (DS) bit in Exception Status Register is
independent of the exception cause (EC)).
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20220213080925.1548411-3-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The privileged instruction exception seems to have been introduced in
microblaze v7.00 along with MMU support, so having it wrapped in
MICROBLAZE_v5 ifdefs seems incorrect. Move it out of the ifdef, since all
recent microblaze versions support it.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20220213080925.1548411-1-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When building for a custom board, it is quite common to maintain a
private branch which include some defconfig and .dts files. But to
hook up those .dts files requires modifying a file "belonging" to
upstream U-Boot, the arch/*/dts/Makefile. Forward-porting that branch
to a newer upstream then often results in a conflict which, while it
is trivial to resolve by hand, makes it harder to have a CI do "try to
build our board against latest upstream".
The .config usually includes information on precisely what .dtb(s) are
needed, so to avoid having to modify the Makefile, simply add the
files in (SPL_)OF_LIST to dtb-y.
A technicality is that (SPL_)OF_LIST is not always defined, so rework
the Kconfig symbols so that (SPL_)OF_LIST is always defined (when
(SPL_)OF_CONTROL), but only prompted for in the cases which used to be
their "depends on".
nios2 and microblaze already have something like this in their
dts/Makefile, and the rationale in commit 41f59f6853 is similar to
the above. So this simply generalizes existing practice. Followup
patches could remove the logic in those two makefiles, just as there's
potential for moving some common boilerplate from all the
arch/*/dts/Makefile files to the new scripts/Makefile.dts.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Current code assumes that the vector base address is always at 0x0.
However, this value is configurable for MicroBlaze using the
CONFIG_XILINX_MICROBLAZE0_VECTOR_BASE_ADDR Kconfig option. Update the
reset routines to branch to this location instead.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-10-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current code assumes that the vector base address is always at 0x0.
However, this value is configurable for MicroBlaze, so update the
__setup_exceptions routine to work with any vector base address.
The r4 register is reserved for the vector base address inside
__setup_exceptions and the function prologe/epilogue are also updated to
save and restore r4.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-9-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Migrate CONFIG_SYS_USR_EXCEP to Kconfig. Also, rename it to
XILINX_MICROBLAZE0_USR_EXCEP in order to match the naming convention of
microblaze-generic Kconfig options.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-7-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Microblaze is one the last two users of the CONFIG_SYS_RESET_ADDRESS
macro (the other is arch/powerpc/cpu/mpc8xx/cpu.c, but the macro is not
defined anywhere in powerpc code, so it should be removed there too).
Replace CONFIG_SYS_RESET_ADDRESS usage in start.S with
CONFIG_SYS_TEXT_BASE. If the reset address should really be
user-configurable, a new Kconfig option could be added.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-6-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
To simpify the code, use stack space as scratch memory for endian offset
calculation, rather than saving/restoring the first unused MB vector.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-5-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable SPL_LIBCOMMON_SUPPORT and SPL_LIBGENERIC_SUPPORT if CONFIG_SPL=y, in
order to fix the following link failures:
common/spl/spl.o: in function `board_init_r':
common/spl/spl.c:755: undefined reference to `puts'
...
common/spl/spl.o: in function `board_init_r':
common/spl/spl.c:756: undefined reference to `hang'
common/spl/spl.c:740: undefined reference to `memset'
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-4-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Microblaze has three boot modes defined in microblaze/include/asm/spl.h,
but only booting from NOR flash is currently useable. Add a custom
board_boot_order() implementation so that RAM and SPI boot modes can also
be selected if the corresponding load-image support is present.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-3-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
board_fdt_blob_setup() uses the _end symbol to find the dtb in the non-spl
case. In order to allow microblaze builds to compile successfully with
CONFIG_OF_SEPARATE, the _end symbol must be defined. Align microblaze with
the other architectures and use _end symbol rather than __end to mark the
end of the u-boot binary.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-2-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a host Kconfig for OF_LIBFDT. With this we can use
CONFIG_IS_ENABLED(OF_LIBFDT) directly in the tools build, so drop the
unnecessary indirection.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Switch arc/arm/m68k/microblaze/mips/ppc arch_lmb_reserve() to
arch_lmb_reserve_generic().
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Hai Pham <hai.pham.ud@renesas.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Wolfgang Denk <wd@denx.de>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
GCC's garbage collector works for Microblaze for quite a long time but none
has enabled it.
The same change has be done for example by commit fac4790491 ("arc:
Eliminate unused code and data with GCC's garbage collector").
Before:
text data bss dec hex filename
588760 33592 39192 661544 a1828 u-boot
After:
text data bss dec hex filename
504504 32164 38608 575276 8c72c u-boot
Which saves almost 15% of memory footprint.
Also group symbols/functions to proper section.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CONFIG_NEEDS_MANUAL_RELOC macro was out of Kconfig. Move it there to be
able to use compile-time checks to reduce the number of build paths.
Fixes: f9a882438966 ("dm: core: Convert #ifdef to if() in root.c") for Microblaze
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable SPI drivers and driver model for microblaze.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Implement early init by calling generic board_init_f_alloc_reserve and
board_init_f_init_reserve functions:
* drop SYS_MALLOC_F_LEN related code, as allocation and gd->malloc_base
assignment are taken care of by the generic functions
* drop _gd logic
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Currently, the exceptions setup code is duplicated in pre-relocation and
post-relocation init. Factor out this code to __setup_exceptions asm
routine to get rid of the duplication.
__setup_exceptions is called with a relocation offset parameter (r5)
which is set to zero for pre-reloc init and gd->reloc_off for post-reloc
exception setup.
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add read/write memory utilities for 16 and 32 bits. Add these
api's for both little and big endian systems similar to arm
architecture.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Kconfig symbol CONFIG_STACK_SIZE is used both by ARM and Microblaze
with the same meaning. Move it to menu 'General setup' so that we can use
it for all architectures.
Use the value of CONFIG_STACK_SIZE instead of a hard coded 16 MiB value for
reserving memory in the UEFI sub-system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In order to support the compiler providing information used within
Kconfig itself we cannot have the compiler be determined by
arch/*/config.mk as we will not be able to evaluate that yet. Given
that most documentation tells people to specify CROSS_COMPILE, remove
these references.
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Rick Chen <rick@andestech.com>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
In a few places we have Kconfig entries that set SPL_LDSCRIPT to what is
the default value anyways. Drop these.
Cc: Michal Simek <monstr@monstr.eu>
Cc: Rick Chen <rick@andestech.com>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com> (for Microblaze)
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move these two functions into the irq_funcs.h header file. Also move
interrupt_handler_t as this is used by the irq_install_handler() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions do not use driver model but are fairly widely used in
U-Boot. But it is not clear that they will use driver model anytime soon,
so we don't want to label them as 'legacy'.
Move them to a new irq_func.h header file. Avoid the name 'irq.h' since it
is widely used in U-Boot already.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
