cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYrlYngAKCRDKSWXLKUoM
ITgbAJ9S9xO2QqxtuodWAYMtJfvZ14c7mgCeKnyFTrrBnJkC0wPsGqE71oNJ49o=
=3gGm
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.10
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
Fix the buffer underflow that would occur if puts is called with length
of zero.
Fixes: efa51f2bd6 ("serial: sandbox: Implement puts")
Cc: Sean Anderson <sean.anderson@seco.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
CONFIG_VAL(DEBUG_UART_BASE) expands to CONFIG_DEBUG_UART_BASE or
CONFIG_SPL_DEBUG_UART_BASE or CONFIG_TPL_DEBUG_UART_BASE and allows boards
to set different values for SPL, TPL and U-Boot Proper.
For ns16550 driver this support is there since commit d293759d55
("serial: ns16550: Add support for SPL_DEBUG_UART_BASE").
Signed-off-by: Pali Rohár <pali@kernel.org>
ARM semihosting provides no provisions for determining if there is
pending input. The only way to determine if there is console input is to
do a read (and block until the user types something). For this reason,
we always return true for tstc (since you will always get input if you
try). However, this behavior can cause problems for code which expects
tstc to eventually be empty. In query_console_serial, there is the
following construct:
/* empty input buffer */
while (tstc())
getchar();
with the current implementation, this effectively turns into an infinite
loop. To avoid this, fake tstc by returning false half of the time. This
is generally OK because the other common construct looks like
do {
if (tstc())
process(getchar());
} while (!timeout());
so it's fine if we only read a new character every other loop. This will
break things like CYGACC_COMM_IF_GETC_TIMEOUT, but that could be
reworked to test on the timeout instead of calling tstc again (and
ymodem over semihosted serial is not that useful in the first place).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
These were only ever implied by sunxi platforms, and that usage has
been removed. Current practice is to specify CONFIG_CONS_INDEX in each
board's defconfig.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Use CONFIG_VAL(DEBUG_UART_BASE) instead of CONFIG_DEBUG_UART_BASE, so
proper config value (CONFIG_DEBUG_UART_BASE or CONFIG_SPL_DEBUG_UART_BASE)
is used based on building target.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
TPL_DEBUG_UART_BASE is same as DEBUG_UART_BASE, but applies only for TPL.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Stefan Roese <sr@denx.de>
SPL_DEBUG_UART_BASE is same as DEBUG_UART_BASE, but applies only for SPL.
In some cases base address of UART is different in SPL and proper U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The serial_rockchip.c driver converts platdata to the data structure
used in the ns16550.c file and then calls the function
ns16550_serial_probe().
When compiled with OF_REAL the serial_rockchip.c driver returns
now -ENODEV when probed and does no harm.
The config ROCKCHIP_SERIAL is currently depends on SPL_OF_PLATDATA.
Allow serial port use for both SPL and TPL by removing this
dependency and SPL_BUILD restriction.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip serial driver depends on an enabled NS16550 driver,
so add select SYS_NS16550 to config ROCKCHIP_SERIAL.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When a defconfig for rk3288 is compiled it gives the warning:
rockchip_rk3288_uart: Missing .compatible in
./drivers/serial/serial_rockchip.c
: WARNING: the driver rockchip_rk3288_uart
was not found in the driver list
Fix by renaming U_BOOT_DRIVER name of serial_rockchip.c
to rockchip_uart. Add rk3288 serial support with
a DM_DRIVER_ALIAS define.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip uart DT nodes have "snps,dw-apb-uart" as
fall back string. The driver ns16550.c has CONFIG_IS_ENABLED(OF_REAL)
as condition to of_match and does not copy dtplat data.
For TPL/SPL the driver serial_rockchip.c
is used. Move driver alias to correct driver.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ns16550.c driver has the following conditions for .of_match:
CONFIG_IS_ENABLED(OF_REAL)
For Rockchip SoCs with TPL/SPL and platform data that need serial
support the serial_rockchip.c driver was made. It copies this data
and then calls ns16550_serial_probe(). With the addition of yet an other
SoC type this driver is in need for a little restyle.
Simplify struct rockchip_uart_plat and add extra SoCs with
DM_DRIVER_ALIAS(). Return -ENODEV when the ns16550.c driver
probe function is available.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This adds an implementation of puts for DM. The implementation is not as
clean as for the non-DM puts because we have to handle non-nul-terminated
string. We also handle short writes (though these are probably very
unusual).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds a test to ensure that puts is equivalent to putc called in a
loop. We don't verify the contents of the message to avoid having to
record console output a second time (though that could be added in the
future). The globals are initialized to non-zero values to avoid a
warning; in particular, the character count is off-by-one (but we always
make relative measurements).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This implements puts for sandbox. It is fairly straightforward, except
that we break out the shared color printing functionality into its own
function.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A string like "test\n" would be broken up into the following sequence of
prints by _serial_puts:
puts("test\n")
putc('\r')
Although functionally this is the same as \r\n, it is not the standard
sequence and caused tests to fail. Fix this by excluding the '\n' from
the initial print. The above string will now be broken up like
puts("test")
puts("\r\n")
Since we may now need to call ops->puts twice (with the associated retry
logic), break that part of the function off into a helper.
Fixes: 7a76347189 ("serial: dm: Add support for puts")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This converts the following to Kconfig:
CONFIG_CONS_SCIF0
CONFIG_CONS_SCIF1
CONFIG_CONS_SCIF2
CONFIG_CONS_SCIF4
CONFIG_CONS_SCIFA0
Signed-off-by: Tom Rini <trini@konsulko.com>
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYkxUZwAKCRDKSWXLKUoM
IXJ2AKCQcoFK7wanCCvZfuEJCSwO5E4eCACginE2CFVXKcY1P8ta4ESusjY2TH0=
=HOoS
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc1 v2
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
Some serial drivers can be vastly more efficient when printing multiple
characters at once. Non-DM serial has had a puts option for these sorts
of drivers; implement it for DM serial as well.
Because we have to add carriage returns, we can't just pass the whole
string directly to the serial driver. Instead, we print up to the
newline, then print a carriage return, and then continue on. This is
less efficient, but it is better than printing each character
individually. It also avoids having to allocate memory just to add a few
characters.
Drivers may perform short writes (such as filling a FIFO) and return the
number of characters written in len. We loop over them in the same way
that _serial_putc loops over putc.
This results in around sizeof(void *) growth for all boards with
DM_SERIAL. The full implementation takes around 140 bytes.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If semihosting is disabled, then the user has no debugger attached, and
will not see any messages. Don't create a serial device in this
instance, to (hopefully) fall back on another working serial device.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds a serial driver which uses semihosting calls to read and write
to the host's console. For convenience, if CONFIG_DM_SERIAL is enabled,
we will instantiate a serial driver. This allows users to enable this
driver (which has no physical device) without modifying their device
trees or board files. We also implement a non-DM driver for SPL, or for
much faster output in U-Boot proper.
There are three ways to print to the console:
Method Baud
================== =====
smh_putc in a loop 170
smh_puts 1600
smh_write with :tt 20000
================== =====
These speeds were measured using a 175 character message with a J-Link
adapter. For reference, U-Boot typically prints around 2700 characters
during boot on this board. There are two major factors affecting the
speed of these functions. First, each breakpoint incurs a delay. Second,
each debugger memory transaction incurs a delay. smh_putc has a
breakpoint and memory transaction for every character. smh_puts has one
breakpoint, but still has to use a transaction for every character. This
is because we don't know the length up front, so OpenOCD has to check if
each character is nul. smh_write has only one breakpoint and one memory
transfer.
DM serial drivers can only implement a putc interface, so we are stuck
with the slowest API. Non-DM drivers can implement puts, which is vastly
more efficient. When the driver starts up, we try to open :tt. Since
this is an extension, this may fail. If it does, we fall back to
smh_puts. We don't check :semihosting-features, since there are
nonconforming implementations (OpenOCD) which don't implement it (but
*do* implement :tt).
Some semihosting implementations (QEMU) don't handle READC properly. To
work around this, we try to use open/read (much like for stdin) if
possible.
There is no non-blocking I/O available, so we don't implement pending.
This will cause __serial_tstc to always return true. If
CONFIG_SERIAL_RX_BUFFER is enabled, _serial_tstc will try and read
characters forever. To avoid this, we depend on this config being
disabled.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_LPUART
CONFIG_LPUART_32B_REG
And note that CONFIG_LPUART_32B_REG is unused in code.
Signed-off-by: Tom Rini <trini@konsulko.com>
Serial IP has output buffer which status is indicated by two bits. If fifo
if empty or full. Default configuration is that chars are pushed to fifo
till it is full. Time to time it is visible that chars are scambled and
logs are not visible. Not sure what it is exactly happening but all the
time it helps to change driver behavior to write only one char at a time.
That's why enable this mode when debug uart is enabled not to see scrambled
chars in debug by default.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/332b2106d7a8190dd1001b5387f8bd1fba2e061b.1648205405.git.michal.simek@xilinx.com
The stdout-path property in the device tree does not necessarily
point at a serial device. On machines such as the Apple M1 laptops
where the serial port isn't easy to access and users expect to see
console output on the integrated display stdout-path may point at
the device tree node for the framebuffer for example.
If stdout-path does not point at a node for a serial device, the
serial_check_stdout() will not find a bound device and will drop
down into code that attempts to use lists_bind_fdt() to bind a
device anyway. However, that fallback code does not check that
the uclass of the device is UCLASS_SERIAL. So if stdout-path points
at the framebuffer instead of the serial device it will return a
UCLASS_VIDEO device. Since the code that calls this function
expects the returned device to be a UCLASS_SERIAL device, U-Boot
will crash as soon as it attempts to send output to the console.
Add a check here to verify that the uclass of the bound device
really is UCLASS_SERIAL. If it isn't, serial_check_stdout() will
return an error and serial_find_console_or_panic() will use the
serial device with sequence number 0 as the console and all is fine.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Quite a few RISC-V emulators and ISS (including Spike) have host
transfer interface (HTIF) based console. This patch adds HTIF
based console driver for RISC-V platforms which depends totally
on DT node for HTIF register base address.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
if CONFIG_DM_STDIO is defined but SERIAL_PRESENT not,
gcc drops warnings for serial_stub_* functions
that they are defined but not used.
Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
nulldev_serial_input is static and not used in this file,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When building sandbox_defconfig with CONFIG_DM_VIDEO=n a link time error
occurs:
in function `sandbox_serial_pending':
drivers/serial/sandbox.c:101: undefined reference to `video_sync_all'
video_sync_all() is only defined if we have CONFIG_DM_VIDEO=y.
Calling this function in a serial driver looks quite hackish
but at least let's add the missing build constraint.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYeg7sQAKCRDKSWXLKUoM
IVhJAKCAiNx/joEeFBJ0XgThtJzFhCjdMwCfYKY9Ewz4L0n2I56lDgR3UJroct0=
=HtB+
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
At present only the backspace key is supported in U-Boot, when running as
an EFI app. Add support for arrows, home and end as well, to make the CLI
more friendly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The only place we use CONFIG_CPU_ARMV8 was in the arm_dcc serial driver.
Switch this to CONFIG_ARM64 today, and if in the future we need finer
granularity tuning here, a new CONFIG_SERIAL option needs to be
introduced.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.
With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.
Signed-off-by: Tom Rini <trini@konsulko.com>
There is no maintainer entry for serial_mvebu_a3700.c. Add entry with Pali
and Stefan as maintainers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Sometimes UART stops transmitting characters after UART clock is changed
back to XTAL. In this state UART fifo is always full. Kernel during early
boot wants to print output on UART and is waiting for non-empty UART fifo.
Which leads to CPU hangup without any (debug) output on UART.
Marvell Armada 3700 Functional Specifications says that for programming
fractional divisor registers it is required to disable UART, enable
loopback mode, reset fifos, program registers, disable loopback mode,
release reset of fifos and enable UART.
But these steps do not fix above mentioned issue that UART hangup. Also
gating UART clock does not help. And even resetting UART state machines do
not help.
Experiments showed that UART fifo is unblocked after board is being reset
(during board reset UART HW transmit UART fifo even CPU is not executing
kernel/bootloader anymore).
And another experiments showed that same workaround can be achieved also
by external reset of UART HW (without need to reset board).
So do not implement any of "Marvell recommended" steps from Functional
Specifications as they do not work. And rather prior changing parent clock
back to XTAL, do external reset of UART HW. This operation also resets all
UART registers, so basically it also sets UART clock to default, which is
XTAL. It is unknown why UART hangups and enters such broken state.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The official ls1028a binding of the driver uses the following as
compatibles:
compatible = "fsl,ls1028a-lpuart";
Add the missing compatible to the driver and update the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Generic Interface (GENI) Serial Engine (SE) based uart
can be found on newer qualcomm SOCs, starting from SDM845.
Tested on Samsung SM-G9600(starqltechn)
by chain-loading u-boot with stock bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
