Add support for distro boot. This is especially helpful for external
devices. There is a global boot command which scans a predefined
list of boot targets:
run distro_bootcmd
As well as direct boot commands such as:
run bootcmd_mmc1
run bootcmd_usb
run bootcmd_dhcp
...
Refer to doc/README.distro fo details.
While at it, remove the CONFIG_DRIVE_TYPES define which has not
been used and was meant to be used for multi device boot support
which is now provided by distroboot.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Print also for Colibri iMX6 512MB IT with 64-bit RAM bus.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This doesn't do anything anymore, probably never did.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Migrate GPIOs to using driver model, properly request backlight, MMC/SD
card detect and USB power enable GPIOs and also enable SION bit in pin
muxing for auxiliary, backlight and USB power enable GPIOs.
While at it also update copyright year, clean-up/re-order includes, add
some comments clarifying ifdef scope and do some white-space clean-up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Move console in env from header file to defconfig.
While at it also update copyright year.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now with SPL long since being in place even for recovery using SDP
finally get rid of those nospl configurations.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The PMIC on Apalis iMX6 may have ECC errors in fuses that will prevent
correct settings. Up to one bit error per fuse bank may be reported and
corrected by the ECC logic. Two bit errors can only be reported.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Switch to the generic compressed Kernel image type (zImage) instead of
the U-Boot specific uImage format.
While at it also fix device tree naming for MMC DFU.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
In case USB serial downloader has been used to load U-Boot start the
serial download protocol (SDP) emulation. This allows to download
complete images such as Toradex Easy Installer over USB SDP as well.
This code uses the boot ROM provided boot information to reliably
detect USB serial downloader.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Use ext4 file system by default.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
We have two commands to change the bootmode fuses:
mfgr_fuse which set fuse 0/5 and 0/6
and
updt_fuse which burns bit 4 of 0/5.
Before BSP 2.6 we fused in mfgr_fuse 0x5062, which boots
from the user partition of the eMMC.
To workaround certain hangs we moved to fastboot mode and
using the first bootpartition of the eMMC requiring a fuse
value of 0x5072 which could be achieved by the then added
updt_fuse command. At the same time the mfgr_fuse command
was changed to also fuse 0x5072, revert that second change
so that one can fuse both values, one with just mfgr_fuse
and the later with mfgr_fuse;updt_fuse.
Note that the mfgr_fuse command is only needed at module
production time, a customer might need to use updt_fuse
when upgrading an older module to be compatible with a
newer image. The command is integrated into the image
update scripts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
If the UART is used in DTE mode the RI and DCD bits in UCR3 become
irq enable bits. Both are set to enabled after reset and both likely
are pending.
Disable the bits also on UARTs not used in the boot loader to prevent
an interrupt storm when Linux enables the UART interrupts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Keep debug code at the end of the function.
Use a one line informational message for the PMIC only.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
In the Linux device tree we use 40Ohm drive strength. So use the same
value in U-Boot.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
During porting to 2016.11 the check of a SD (mmc2) interface
was dropped, this was unintended.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add support for distro boot. This is especially helpful for external
devices. There is a global boot command which scans a predefined
list of boot targets:
run distro_bootcmd
As well as direct boot commands such as:
run bootcmd_mmc1
run bootcmd_mmc2
run bootcmd_usb
run bootcmd_dhcp
...
Refer to doc/README.distro for details.
While at it, remove the CONFIG_DRIVE_TYPES define which has not
been used and was meant to be used for multi device boot support
which is now provided by distroboot.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This doesn't do anything anymore, probably never did.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Migrate GPIOs to using driver model, properly request backlight,
Ethernet PHY reset, MMC/SD card detect and USB power GPIOs and also
enable SION bit in pin muxing for Apalis, backlight, eMMC reset,
Ethernet PHY reset and USB power enable GPIOs.
While at it also update copyright year, clean-up/re-order includes,
add some comments clarifying ifdef scope and do some White-space
clean-up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Move console in env from header file to defconfig.
While at it also update copyright year and remove spurious comments and
new lines.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now with SPL long since being in place even for recovery using SDP
finally get rid of those nospl configurations.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Specific ARP timeout sometimes causes ARP timeout during nfs loading
of the fitImage.
Signed-off-by: Joonas Aijala <joonas.aijala@ge.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
