Commit graph

553 commits

Author SHA1 Message Date
Jakob Unterwurzacher
cdeb4d780a rockchip: spi: enable support for the rk_spi driver for the RK3399
The existing Rockchip SPI (rk_spi.c) driver also matches the hardware
block found in the RK3399.  This has been confirmed both with SPI NOR
flashes and general SPI transfers on the RK3399-Q7 for SPI1 and SPI5.

This change adds the 'rockchip,rk3399-spi' string to its compatible
list to allow reuse of the existing driver.

X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Philipp Tomsich
9fc354e246 rockchip: spi: rewrite rkspi_set_clk for a more conservative baudrate setting
The baudrate in rkspi was calculated by using an integer division
(which implicitly discarded any fractional result), then rounding to
an even number and finally clamping to 0xfffe using a bitwise AND
operator.  This introduced two issues:
1) for very small baudrates (overflowing the 0xfffe range), the
   bitwise-AND generates rather random-looking (wildly varying)
   actual output bitrates
2) for higher baudrates, the calculation tends to 'err towards a
   higher baudrate' with the actual error increasing as the dividers
   become very small. E.g., with a 99MHz input clock, a request
   for a 20MBit baudrate (99/20 = 4.95), a 24.75 MBit would be use
   (which amounts to a 23.75% error)... for a 34 MBit request this
   would be an actual outbout of 49.5 Mbit (i.e. a 45% error).

This change rewrites the divider selection (i.e. baudrate calculation)
by making sure that
a) for the normal case: the largest representable baudrate below the
   requested rate will be chosen;
b) for the denormal case (i.e. when the divider can no longer be
   represented), the lowest representable baudrate is chosen.

Even though the denormal case (b) may be of little concern in real
world applications (even with a 198MHz input clock, this will only
happen at below approx. 3kHz/3kBit), our board-verification team kept
complaining.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-05-10 13:37:21 -06:00
Philipp Tomsich
bd37671434 rockchip: spi: rk_spi: dynamically select an module input rate
The original clock/bitrate selection code for the rk_spi driver was a
bit limited, as it always selected a 99MHz input clock rate (which
would allow for a maximum bitrate of 49.5MBit/s), but returned -EINVAL
if a bitrate higher than 48MHz was requested.

To give us better control over the bitrate (i.e. add more operating
points, especially at "higher" bitrate---such as above 9MBit/s), we
try to choose 4x the maximum frequency (clamped to 50MBit) from the
DTS instead of 99MHz... for most use-cases this will yield a frequency
of 198MHz, but is flexible to go beyond this in future configurations.

This also rewrites the check to allow frequencies of up to half the
SPI module rate as bitrates and then clamps to whatever the DTS allows
as a maximum (board-specific) frequency and does away with the -EINVAL
when trying to select a bitrate (for cases that exceeded the hard
limit) and instead consistently clamps to the lower of the hard limit,
the soft limit for the SPI bus (from the DTS) or the soft limit for
the SPI slave device.

This replaces
  "rockchip: spi: rk_spi: select 198MHz input to the SPI module for the RK3399"
  "rockchip: spi: rk_spi: improve clocking code for the RK3399"
from earlier versions of this series.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-05-10 13:37:21 -06:00
Vikas Manocha
890bafd752 stm32f7: use clock driver to enable qspi controller clock
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
2017-05-08 11:38:41 -04:00
Suniel Mahesh
2f54205829 drivers: spi: Remove duplicate .probe method
.probe method has been assigned twice when declaring
a driver with U_BOOT_DRIVER(). Removed one of them.
Here is the last commit which had the duplicate entry:
"spi: omap3: Convert to driver model"
(sha1: 77b8d04854)

Signed-off-by: Suniel Mahesh <suniel.spartan@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-05-03 11:52:16 +05:30
Moritz Fischer
ac6991fb5f zynq: spi: Honour the activation / deactivation delay
This is not currently implemented. Add support for this so that the
Chrome OS EC can be used reliably.

Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-05-03 11:03:04 +05:30
Wenyou Yang
61a77ce1d5 spi: atmel: check GPIO validity before using cs_gpios
Before using the cs_gpio, check if the GPIO is valid or not.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-05-03 10:58:54 +05:30
Tom Rini
ea3310e8aa Blackfin: Remove
The architecture is currently unmaintained, remove.

Cc: Benjamin Matthews <mben12@gmail.com>
Cc: Chong Huang <chuang@ucrobotics.com>
Cc: Dimitar Penev <dpn@switchfin.org>
Cc: Haitao Zhang <hzhang@ucrobotics.com>
Cc: I-SYST Micromodule <support@i-syst.com>
Cc: M.Hasewinkel (MHA) <info@ssv-embedded.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Strubel <strubel@section5.ch>
Cc: Peter Meerwald <devel@bct-electronic.com>
Cc: Sonic Zhang <sonic.adi@gmail.com>
Cc: Valentin Yakovenkov <yakovenkov@niistt.ru>
Cc: Wojtek Skulski <info@skutek.com>
Cc: Wojtek Skulski <skulski@pas.rochester.edu>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-05 13:52:01 -04:00
Stefan Roese
706865afe5 dm: core: Add flags parameter to device_remove()
This patch adds the flags parameter to device_remove() and changes all
calls to this function to provide the default value of DM_REMOVE_NORMAL
for "normal" device removal.

This is in preparation for the driver specific pre-OS (e.g. DMA
cancelling) remove support.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:15:10 -06:00
Suresh Gupta
38a5c57ac5 spi: fsl_qspi: Add support for single chip select
SOC’s like LS1012A has only one chip select signal for QSPI flash.
Avoid scanning other flash.

Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-03-28 09:10:12 -07:00
Jean-Jacques Hiblot
b06a381a69 drivers: ti_qspi: use syscon to get the address ctrl_mod_mmap register
We used to get the address of the optionnal ctrl_mod_mmap register as the
third memory range of the "reg" property. the linux driver moved to use a
syscon instead. In order to keep the DTS as close as possible to that of
linux, we move to using a syscon as well.

If SYSCON is not supported, the driver reverts to the old way of getting
the address from the 3rd memory range

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2017-03-22 07:27:19 -06:00
Simon Glass
e160f7d430 dm: core: Replace of_offset with accessor
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-02-08 06:12:14 -07:00
Michael Kurz
d4363baada ARM: SPI: stm32: add stm32f746 qspi driver
This patch adds support for the QSPI IP found in stm32f7 devices.

Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
2017-01-28 14:04:50 -05:00
Jagan Teki
68e7999ba9 spi: Zap cf_qspi driver and related code
Dropped becuase
- driver not used any board.
- no dm conversion.

Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Richard Retanubun <richardretanubun@ruggedcom.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Acked-by: Angelo Dureghello <angelo@sysam.it>
2017-01-15 18:29:04 +01:00
Jagan Teki
ee86e0d2fe spi: Zap ep93xx_spi driver and related code
Dropped becuase
- driver and related configs not used any board.
- no dm conversion.

Cc: Heiko Schocher <hs@denx.de>
Cc: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
2017-01-13 22:47:14 +01:00
Vignesh R
b63b46313e spi: cadence_qspi_apb: Use 32 bit indirect read transaction when possible
According to Section 11.15.4.9.1 Indirect Read Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface reads until the last word of an indirect transfer
So, make sure that QSPI indirect reads are 32 bit sized except for the
final read. If the rxbuf is unaligned then use bounce buffer, so that
readsl() can be used instead of readsb() to avoid non 32-bit accesses.

[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-01-04 16:38:35 +01:00
Vignesh R
57897c13de spi: cadence_qspi_apb: Use 32 bit indirect write transaction when possible
According to Section 11.15.4.9.2 Indirect Write Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface writes until the last word of an indirect transfer
otherwise indirect writes is known to fails sometimes. So, make sure
that QSPI indirect writes are 32 bit sized except for the last write. If
the txbuf is unaligned then use bounce buffer to avoid data aborts.

So, now that the driver uses bounce_buffer, enable CONFIG_BOUNCE_BUFFER
for all boards that use Cadence QSPI driver.

[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-01-04 16:38:12 +01:00
Jagan Teki
cb71c6d854 spi: Zap armada100_spi.c and env
armada100_spi.c and related env is zapping becuase
of "no DM conversion".

Cc: Ajay Bhargav <ajay.bhargav@einfochips.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
2016-12-21 12:18:47 +01:00
Jagan Teki
353f6a770f spi: Zap mpc52xx_spi.c, config and related code
armada100_spi.c, related config options and related codes
are zapping becuase of "no DM conversion".

Cc: Werner Pfister <Pfister_Werner@intercontrol.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-21 12:14:37 +01:00
Phil Edworthy
6d72810c66 spi: cadence_qspi: Move DT prop code to match layout
Move the code to read the "sram-size" property into the other code
that reads properties from the node, rather than the SF subnode.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:28 +01:00
Phil Edworthy
22e63ff3a2 spi: cadence_qspi: Fix CS timings
The Cadence QSPI controller has specified overheads for the various CS
times that are in addition to those programmed in to the Device Delay
register. The overheads are different for the delays.

In addition, the existing code does not handle the case when the delay
is less than a SCLK period.

This change accurately calculates the additional delays in Ref clocks.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
3c56953219 spi: cadence_qspi: Remove returns from end of void functions
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
7d403f284c spi: cadence_qspi: Use spi mode at the point it is needed
Instead of extracting mode settings and passing them as separate
args to another function, just pass the SPI mode as an arg.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
7e76c4b08a spi: cadence_qspi: Clean up the #define names
A lot of the #defines are for single bits in a register, where the
name has _MASK on the end. Since this can be used for both a mask
and the value, remove _MASK from them.

Whilst doing so, also remove the unnecessary brackets around the
constants.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
db37cc9c39 spi: cadence_qspi: Use #define for bits instead of bit shifts
Most of the code already uses #defines for the bit value, rather
than the shift required to get the value. This changes the remaining
code over.

Whislt at it, fix the names of the "Rd Data Capture" register defs.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
0ceb4d9e9a spi: cadence_qspi: Better debug information on the SPI clock rate
Show what the output clock rate actually is.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
32068c42a7 spi: cadence_qspi: Fix baud rate calculation
With the existing code, when the requested SPI clock rate is near
to the lowest that can be achieved by the hardware (max divider
of the ref clock is 32), the generated clock rate is wrong.
For example, with a 50MHz ref clock, when asked for anything less
than a 1.5MHz SPI clock, the code sets up the divider to generate
25MHz.

This change fixes the calculation.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
cc80a897e4 spi: cadence_qspi: Fix clearing of pol/pha bits
Or'ing together bit positions is clearly wrong.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Simon Glass
1b7c28f514 spi: Add error checking for invalid bus widths
At present an invalid bus width prints a message but does not return an
error. This is the opposite of the correct behaviour. Adjust it to avoid
code bloat in the common case, and avoid hard-to-debug failure in the
uncommon case.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:38:30 +01:00
Nishanth Menon
3891a54f47 ARM: DRA7x/AM57xx: Get rid of CONFIG_AM57XX
CONFIG_AM57XX is just an unnecessary macro that is redundant given So,
remove the same instead of spreading through out the u-boot source
code and getting in the way to maintain common code for DRA7x family.

Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-03 13:21:11 -05:00
Simon Glass
28f9885875 spi: Add a debug() on bind failure
This is an uncommon error but we may as well have a debug() message when
it happens.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:30 -07:00
Simon Glass
b42524744d rockchip: spi: Honour the deactivation delay
This is not currently implemented. Add support for this so that the Chrome
OS EC can be used on jerry.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:30 -07:00
Simon Glass
6e019c4f28 rockchip: spi: Add support for of-platdata
Allow this driver to be used with of-platdata on rk3288.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:30 -07:00
Simon Glass
71634f289d spi: Add of-platdata support to SPI and SPI flash
Some boards may want to use these subsystems with of-platdata in SPL. Add
support for this by avoiding any device tree access in this case.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:30 -07:00
Chris Packham
ebfa18cb3d spi: kirkwood_spi: implement mvebu_spi_set_mode()
Set the appropriate bits in the interface config register based
on the SPI_ mode flags.

Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
2016-11-18 13:04:52 +05:30
Vignesh R
948b8bbd5f spi: ti_qspi: Fix baudrate divider calculation
Fix the divider calculation logic to choose a value so that the
resulting baudrate is either equal to or closest possible baudrate less
than the requested value. While at that, cleanup ti_spi_set_speed().

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-11-13 15:54:37 -05:00
Wenyou Yang
0eafd4b776 dm: at91: Add driver model support for the spi driver
Add driver model support while retaining the existing legacy code.
This allows the driver to support boards that have converted to
driver model as well as those that have not.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
2016-10-28 18:37:15 +02:00
Simon Glass
df87e6b1b8 libfdt: Sync fdt_for_each_subnode() with upstream
The signature for this macro has changed. Bring in the upstream version and
adjust U-Boot's usages to suit.

Signed-off-by: Simon Glass <sjg@chromium.org>
Update to drivers/power/pmic/palmas.c:
Signed-off-by: Keerthy <j-keerthy@ti.com>

Change-Id: I6cc9021339bfe686f9df21d61a1095ca2b3776e8
2016-10-13 14:10:32 -06:00
Tom Rini
711b534120 Merge git://git.denx.de/u-boot-fsl-qoriq
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	include/configs/ls1021aqds.h
	include/configs/ls1021atwr.h
2016-10-12 08:29:42 -04:00
Robert P. J. Day
fc0b5948e0 Various, accumulated typos collected from around the tree.
Fix various misspellings of:

 * deprecated
 * partition
 * preceding,preceded
 * preparation
 * its versus it's
 * export
 * existing
 * scenario
 * redundant
 * remaining
 * value
 * architecture

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-10-06 20:57:40 -04:00
York Sun
3c6b1767c2 spi: fsl_qspi: Preserve endianness of QSPI MCR
The endianness can be changed by RCW + PBI sequence. It may have
other than power on reset value.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Yuan Yao <yao.yuan@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-10-06 14:28:32 -07:00
Stefan Roese
3fda4ef395 spi: Add driver for Marvell Armada 3700 SoC
The SPI IP core in the Marvell Armada 3700 is similar to the one in the
other Armada SoCs. But the differences are big enough that it makes
sense to introduce a new driver instead of cluttering the old
kirkwood driver with #ifdef's.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-09-27 17:29:52 +02:00
Masahiro Yamada
1221ce459d treewide: replace #include <asm/errno.h> with <linux/errno.h>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content.  (both just wrap <asm-generic/errno.h>)

Replace all include directives for <asm/errno.h> with <linux/errno.h>.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-23 17:55:42 -04:00
Tom Rini
19d051a2b7 Merge branch 'master' of git://git.denx.de/u-boot-spi 2016-09-22 11:36:45 -04:00
Jagan Teki
21b1dd18f1 spi: Kconfig: Move FSL_QSPI entry to non-dm place
Since FSL_QSPI driver still supporting non-dm code
better to move the Kconfig from DM undefined place.

Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-09-22 14:16:28 +05:30
Michal Simek
5f647c2284 spi: zynq: Use variable to remove u32 to u64 conversions
Current code generates warning when it is compiled for arm64:
Warnings:
In file included from drivers/spi/zynq_spi.c:14:0:
drivers/spi/zynq_spi.c: In function ‘zynq_spi_init_hw’:
drivers/spi/zynq_spi.c:95:9: warning: large integer implicitly truncated
to unsigned type [-Woverflow]
  writel(~ZYNQ_SPI_ENR_SPI_EN_MASK, &regs->enr);
         ^
./arch/arm/include/asm/io.h:146:34: note: in definition of macro
‘writel’
 #define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v;
})
                                  ^
drivers/spi/zynq_spi.c: In function ‘zynq_spi_release_bus’:
drivers/spi/zynq_spi.c:177:9: warning: large integer implicitly
truncated to unsigned type [-Woverflow]
  writel(~ZYNQ_SPI_ENR_SPI_EN_MASK, &regs->enr);
         ^
./arch/arm/include/asm/io.h:146:34: note: in definition of macro
‘writel’
 #define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v;
})
                                  ^
This patch is using one variable to do conversion via u32 variable.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-09-22 07:33:20 +02:00
Jagan Teki
08fe9c294f spi: Use mode for rx mode flags
Make rx mode flags as generic to spi, earlier mode_rx is
maintained separately because of some flash specific code.

Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-09-22 01:02:28 +05:30
Vignesh R
28b69f6488 spi: ti_qspi: Remove unnecessary udelay for AM437x
This udelay() was added as an HACK and is no longer required. All
read/write/erase operations work fine even without this delay. Hence,
remove the udelay() call.

Tested read/write/erase operation on AM437x SK. Also tested QSPI Boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-09-22 00:58:26 +05:30
Vignesh R
260368507a spi: ti_qspi: use 128 bit transfer mode when writing to flash
TI QSPI has four 32 bit data registers which can be used to transfer 16
bytes of data at once. The register group QSPI_SPI_DATA_REG_3,
QSPI_SPI_DATA_REG_2, QSPI_SPI_DATA_REG_1 and QSPI_SPI_DATA_REG is
treated as a single 128-bit word for shifting data in and out. The bit
at QSPI_SPI_DATA_REG_3[31] position is the first bit to be shifted out
in case of 128 bit transfer mode. Therefore the first byte to be written
to flash should be at QSPI_SPI_DATA_REG_3[31-25] position.
Instead of writing 1 byte at a time when interacting with SPI NOR flash,
make use of all the four registers so that 16 bytes can be transferred
in one go.

With this patch, the flash write speed increases from ~250KBs/ to
~650KB/s on DRA74 EVM.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-09-22 00:58:26 +05:30
Lad, Prabhakar
d2998286fc spi: zynq_spi: Fix infinite looping while xfer
During spi transfer, for example:
sspi 1:1.0 8 ff

the rx_len values will  be:
rx_len = 0
rx_len = 4294967295

This caused a busy looping during xfer, this patch fixes it
by adding a check while reading the rx fifo

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-09-22 00:58:26 +05:30