The function fdt_fixup_dr_usb is specific to fsl/nxp. So,
make the function name explicit and rename fdt_fixup_dr_usb
into fsl_fdt_fixup_dr_usb.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
Users migrating Freescale's PowerPC SoC U-Boot code to their custom
board, often overlook the need to execute set_liodns() and
setup_portals() being called by platform files.
So Move set_liodns() and setup_portals() to common u-boot boot
sequence
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
XFI does not work stable on current board, it's due to heat sink issue,
to make it work stable the board needs additional heat sink, enable two
XFI lanes only. Right now we do not have such an erratum for the issue,
so use a define CONFIG_SYS_FSL_B4860QDS_XFI_ERR to identify it.
The workaround will only be used in XFI protocols and only if the
hwconfig indicates that XFI is prefered.
A new VSC3308 config function is used instead of re-use the original
function, to avoid making the function complex and ugly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes2 lanes EFGH either go to SFP or AMC riser card slot2.
By default AMC will be configured even if no hwconfig is specified.
To enable XFI via SFP use the below hwconfig:
fsl_b4860_serdes2:sfp_amc=sfp
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@ffeescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We need following changes to make xfi work on B4:
1. set cross-point switch VSC3308 to use sfp config when running xfi;
2. add 10G interface check for xfi;
3. set phy address for xfi so the 10G ports can be registered by mdio;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add the support of newly added LC VCO SerDes protocols
for configuration of IDT and VSC crossbar
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
B4860, B4440, B4420 and B4220 have MAPLE, so enable law creation
for them only. Remove static LAW creation for MAPLE.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This function can fail if the device tree runs out of space. Rather than
silently booting with an incomplete device tree, allow the failure to be
detected.
Unfortunately this involves changing a lot of places in the code. I have
not changed behvaiour to return an error where one is not currently
returned, to avoid unexpected breakage.
Eventually it would be nice to allow boards to register functions to be
called to update the device tree. This would avoid all the many functions
to do this. However it's not clear yet if this should be done using driver
model or with a linker list. This work is left for later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
find_tlb_idx() is called in board_early_init_r() on multiple boards.
The return value is not checked before being used to disable a TLB.
In normal case the return value wouldn't be -1. In case of a mis-
configuration during porting to a new board, checking the return value
may be helpful to reveal some user errors.
Signed-off-by: York Sun <yorksun@freescale.com>
Crossbars and IDT were not getting configured for Serdes2 protocol
0x9d for B4420.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
B4860QDS has a PowerOne ZM7300 programmable digital Power
Manager which is programmed as per the value read from
the fuses.
Reference for this code is taken from t4qds VID implementation.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
SerDes PLLs may not lock reliably at 5 G VCO configuration(A006384)
and at cold temperatures(A006475), workaround recalibrate the
PLLs with some SerDes configuration
Both these errata are only applicable for b4 rev1.
So, make workaround for these errata conditional,
depending upon soc version.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Change setting of SerDes2 refclk2 to have the default value as it is
coming on board that is 156.25MHz, for XFI to work.
Also change PLL_NUM variable to the one defined in config_mpc85xx.h
for B4860 and B4420.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On B4860 and B4420, some serdes protocols can be used with LC VCO as
well as Ring VCO options.
Addded Alternate options with LC VCO for such protocols.
For example protocol 0x2a on srds 1 becomes 0x29 if it is LC VCO.
The alternate option has the same functionality as the original option;
the only difference being LC VCO rather than Ring VCO.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1) SerDes2 Refclks have been set properly to make
PCIe SATA to work as it work on SerDes refclk of 100MHz
2) Mask the SerDes's device reset request before changing
the Refclks for SerDes1 and SerDes2 for PLL locks to
happen properly, device reset request bit unmasked
after SerDes refclks configuration
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1) Add new SerDes1 protocols having Aurora in them
2) Add VSC cross point connections for Aurora to work with
CPRI and SGMIIs
3) Configure VSC crossbar switch to connect SerDes1
lanes to aurora on board, by checking SerDes1 protocols
4) SerDes1 Refclks have been set properly to make
Aurora, CPRI and SGMIIs to work together properly
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This allows to share some common code for the boards that use a corenet
base SoC.
Two different versions of the function are available in
fsl_corenet_serdes.c and fsl_corenet2_serdes.c files.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix t1040qds.c]
Acked-by: York Sun <yorksun@freescale.com>
1) Add support in B4860 board files for using IDT driver where
IDT8T49N222A is a low phase noise Frequency Translator / Synthesizer
that generate different refclks for SerDes modules, used this driver
for reconfiguring SerDes1 Refclks(based on SerDes1 protocols)
for CPRI to work. CPRI works on 122.88MHz and default refclks coming
on board are not suitable for it
2) Move SerDes1 refclk1 source selection from eth_b4860qds.c file
to b4860qds board file, as SerDes1 Refclk1 would come from
PHY MUX in case of certain protocols, that have been checked here.
This change would make on board SGMIIs to work
3) Add I2C addresses for IDT8T49N222A devices in board/include file
4) Add define for PCA-I2C bus multiplexer, on which IDT devices exist
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Crossbar switches were wrongly programmed to
route the CPRI lanes to SFP as the connectivity table
was not correct.
Modified it correctly for SFPs connections.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Move these fields into arch_global_data and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Update for bsc9132qds.c, b4860qds.c]
Signed-off-by: Tom Rini <trini@ti.com>
This function is called by "qixis_reset switch" command
and switch settings are calculated from FPGA/qixis registers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
B4860QDS is a high-performance computing evaluation, development and
test platform supporting the B4860 QorIQ Power Architecture processor.
B4860QDS Overview
------------------
- DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,
ECC, 4 GB of memory in two ranks of 2 GB.
- DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 2 GB of memory. Single rank.
- SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point
16x16 switch VSC3316
- SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point
8x8 switch VSC3308
- USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode.
- B4860 UART port is available over USB-to-UART translator USB2SER or over
RS232 flat cable.
- A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper
connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA
connector ports 0 and 2 for AMC mode.
- The B4860 configuration may be loaded from nine bits coded reset
configuration reset source. The RCW source is set by appropriate
DIP-switches:
- 16-bit NOR Flash / PROMJet
- QIXIS 8-bit NOR Flash Emulator
- 8-bit NAND Flash
- 24-bit SPI Flash
- Long address I2C EEPROM
- Available debug interfaces are:
- On-board eCWTAP controller with ETH and USB I/F
- JTAG/COP 16-pin header for any external TAP controller
- External JTAG source over AMC to support B2B configuration
- 70-pin Aurora debug connector
- QIXIS (FPGA) logic:
- 2 KB internal memory space including
- IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK,
DDRCLK1, 2 and RTCCLK.
- Two 8T49N222A SerDes ref clock devices support two SerDes port clocks
- total four refclk, including CPRI clock scheme
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
