Nothing selects ARMADA_64BIT. Instead the 64-bit SoCs just select ARM64
directly. Remove the unused config item.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CONFIG_MVEBU_NAND_BOOT, CONFIG_MVEBU_SPI_BOOT, CONFIG_MVEBU_MMC_BOOT and
CONFIG_MVEBU_UBOOT_DFLT_NAME are unused when CONFIG_CMD_MVEBU_BUBT is not
enabled. So hide them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
zynqmp_pm_is_function_supported() which checks feature support on som,
which is implemented in firmware_zynqmp.c driver. As mini configuration
does not use firmware driver, so create a weak function to avoid
compilation error on zynqmp mini configuration.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/c60655a509956b8fc3a81671a7dc51157f3973db.1651048030.git.michal.simek@xilinx.com
board_get_usable_ram_top() was designed for getting the top most location
for U-Boot allocation that's why function itself supports via total_size
parameter to find out where the right location for U-Boot is.
But function itself is also reused by different (EFI) which is passing
total_size as 0 to find out where the usable ram top is. For this case
doesn't make sense (a waste time) to call any lmb functions.
That's why simply return gd->ram_top.
And gd->ram_top is filled already based on previous call for U-Boot iself.
The same solution is also used by stm32mp by commit 92b611e8b0 ("stm32mp:
correctly handle board_get_usable_ram_top(0)") and commit c8510e397f
("stm32mp: Fix board_get_usable_ram_top()").
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/44470619e74f3e480b70deac24578e3e0d5c907e.1651225945.git.michal.simek@amd.com
- Migrate CONFIG_MTD_CONCAT to Kconfig, use CONFIG_VAL/IS_ENABLED in
more places, rename SPL_LEGACY_IMAGE_SUPPORT to
SPL_LEGACY_IMAGE_FORMAT and update some related dependencies for TI
platforms.
Update the diagnostic message with revised location of document, which
changed in 3e9fddfc4f ("doc: Move devicetree control doc to rST")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Drop CONFIG_NEEDS_MANUAL_RELOC ifdefs in board_init_r() and use
IS_ENABLED() instead. Also, use the MANUAL_RELOC() macro to update the
initcall pointers.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
This converts the following to Kconfig:
CONFIG_MTD_CONCAT
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
There is currently no support for PRE_CONSOLE_BUFFER in SPL, but if
and when that gets implemented, one would almost certainly want to use
a different address and/or size for the buffer (e.g., U-Boot proper
might specify an address in DRAM and a generous buffer, while SPL
would be much more constrained).
So a prerequisite for adding SPL_PRE_CONSOLE_BUFFER is to make the
code use SPL_-specific values. No functional change.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
TI secure devices chain-of-trust depends on FIT image processing,
enable it by default on these devices. This also reduces the delta
between the secure and non-secure defconfig files.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Non-FIT image loading support should be disabled for TI secure
devices as the image handlers for those image types do not follow
our secure boot checks.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Booting of non-FIT images bypass our chain-of-trust boot flow,
these options should not be allowed when high security is set.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This matches what this support is called in the non-SPL case. The postfix
_SUPPORT is redundant as enabling Kconfig options implies support.
With this we can use CONFIG_IS_ENABLED() as needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
-----BEGIN PGP SIGNATURE-----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=s7xn
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220510' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add new STM32 MCU boards and Documentation
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
We should only build support for misc if the appropriate SPL/TPL symbol
is defined. To ease the transition, make SPL/TPL_MISC default to MISC.
This is necessary because many drivers don't specify their dependencies
properly. These defaults can be removed once all drivers depend on the
appropriate config.
Fixes: aaba703fd0 ("spl: misc: Allow misc drivers in SPL and TPL")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
[trini: Add VPL_MISC symbol, handle like SPL/TPL_MISC]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add stm32746g-eval_defconfig for stm32746g evaluation board to
build U-Boot proper.
Full board description can be found here :
https://www.st.com/en/evaluation-tools/stm32746g-eval.html
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As stm32f46-disco, stm32f769-disco and stm32746g-eval are very similar
except their respective device tree file. These 3 boards uses the same
TARGET_STM32F746_DISCO flag (so same include/configs/stm32f746-disco.h
and same board file board/st/stm32f746-disco/stm32f746-disco.c)
To be able to compile these 3 boards, replace the hard-coded device-tree
name in include/configs/stm32f746-disco.h by CONFIG_DEFAULT_DEVICE_TREE
which is set in each board defconfig file with the correct value.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Replace CONFIG_SUPPORT_SPL by CONFIG_SPL_BUILD to allow
dram_init() execution when using none SPL defconfig
(stm32f746-disco_defconfig).
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The current stm32f769-disco_defconfig file supports SPL, rename it to
stm32f769-disco_spl_defconfig to reflect the supported configuration.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The current stm32f746-disco_defconfig file supports SPL, rename it to
stm32f746-disco_spl_defconfig to reflect the supported configuration.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This allows to concatenate spl and u-boot binaries together.
Previously, both binaries has to be flashed separately at the correct
offset (spl at offset 0 and u-boot at offset 0x8000).
With this patch, only one binary is generated (u-boot-with-spl.bin)
and has to be copied in flash at offset 0 using openocd for example
or simply copied in exported mass storage.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Always consider USB cable is connected when USB boot device is detected.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add support of phy-tuning properties for sm32-usbphyc's phy tuning
aligned with v5.15 kernel bindings.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
On some STM32 SoC's package, GPIO bank may have hole in their GPIO bank
Example:
If GPIO bank have 16 GPIO pins [0-15].
In particular SoC's package case, some GPIO bank can have less GPIO pins:
- [0-10] => 11 pins;
- [2-7] => 6 pins.
Commit dbf928dd26 ("gpio: stm32f7: Add gpio bank holes management")
proposed a first implementation by not counting GPIO "inside" hole. GPIO
are not displaying correctly using gpio or pinmux command when GPIO holes
are located at the beginning of GPIO bank.
To simplify, consider that all GPIO have 16 GPIO and use the gpio_ranges
struct to indicate if a GPIO is mapped or not. GPIO uclass offers several
GPIO functions ("input", "output", "unused", "unknown" and "func"), use
"unknown" GPIO function to indicate that a GPIO is not mapped.
stm32_offset_to_index() is no more needed and removed.
This must be reflected using the "gpio" command to indicate to user
that a particular GPIO is not mapped (marked as "unknown") as shown below:
Example for a 16 pins GPIO bank with the [2-7] mapping (only 6 pins
mapped):
GPIOI0 : unknown
GPIOI1 : unknown
GPIOI2 : analog
GPIOI3 : analog
GPIOI4 : alt function 0 push-pull pull-down
GPIOI5 : alt function 0 push-pull pull-down
GPIOI6 : alt function 0 push-pull pull-down
GPIOI7 : analog
GPIOI8 : unknown
GPIOI9 : unknown
GPIOI10 : unknown
GPIOI11 : unknown
GPIOI12 : unknown
GPIOI13 : unknown
GPIOI14 : unknown
GPIOI15 : unknown
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
GPIOF_UNKNOWN becomes a valid pin muxing information to indicate
that a pin is not mapped.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
pinmux_mode[] is linked to gpio_function[] defined in gpio-uclass.c
So reuse the same gpio_func_t enum value
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Long TFTP transfers lead to a wall of # characters on UART, which in
the end may slow down the transfer itself. Use CONFIG_TFTP_TSIZE to
print progress in fewer # characters.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
The Buck3 on DHCOR is used to supply IO voltage. It can output either 3V3
in the default DHCOR configuration, or 2V9 in case of AV96 DHCOR variant
which has extra Empirion DCDC converter in front of the 1V8 IO supply, or
outright 1V8 in case of 1V8 IO DHCOR without the Empirion DCDC converter.
The 2V9 mode in case of AV96 DHCOR variant is used to reduce unnecessarily
high input voltage to the Empirion DCDC converter, so move it into matching
DTSI to stop confusing users.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Long TFTP transfers lead to a wall of # characters on UART, which in
the end may slow down the transfer itself. Use CONFIG_TFTP_TSIZE to
print progress in fewer # characters.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
The DHCOM does ship with KS8851 with 1.5 kiB packet buffer. The DHSOM
may be extended with other MAC options connected to FMC2 bus, like the
DM9000, wih similar limitations. Use default CONFIG_TFTP_BLOCKSIZE of
1468 Bytes instead of 1536 Bytes, which always avoids overflowing the
packet buffers of such limited MACs, which leads to e.g. TFTP timeouts.
This also avoids receiving a short packet fragment at the end of each
TFTP block, which led to reduced performance.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
The SoC seems to lose the values of MCUDIVR, PLL3CR, PLL4CR, RCC_MSSCKSELR
during suspend/resume cycle, cache them and reinstate their values on resume.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable DRAM ASR, auto self-refresh, conditionally, based on DT PWRCTL
register bits. While ASR does save considerable amount of power at
runtime automatically, it also causes LTDC underruns on large panels.
Let user select whether or not ASR is required or not, generally ASR
should be enabled on portable and battery operated devices.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Device tree alignment with Linux kernel v5.18-rc2:
- ARM: dts: stm32: Add support for the emtrion emSBC-Argon
(only the pincontrol part)
- ARM: dts: stm32: Drop duplicate status okay from DHCOM gpioc node
- ARM: dts: stm32: add st,stm32-sdmmc2 compatible on stm32mp151
- ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
- ARM: dts: stm32: use exti 19 as main interrupt to support RTC wakeup on
stm32mp157
- ARM: dts: stm32: add DMA configuration to UART nodes on stm32mp151
- ARM: dts: stm32: keep uart4 behavior on *
- ARM: dts: stm32: Correct masks for GIC PPI interrupts on stm32mp15
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Handle correctly the silicon revision = REV_ID[15:0] of Device Version
and the associated device marking, A to Z on STMicroelectronics STM32MP
SOCs.
This patch prepare the introduction of next STM32MP family,
with STM32MP13x Rev.Z for REV_ID = 1.1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
The function ft_system_setup shouldn't return an error when the
/soc node is absent in the provided device tree but just skip the
updates.
This patch solves an issue when the U-Boot pytest is executed on board.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
On STMicroelectronics boards, the UART can reliably go up to
2000000 bauds when connected to the on-board ST-LINK-V2 for STM32MP15
Unfortunately U-Boot will fall back to 115200 unless higher rates are
declared via CONFIG_SYS_BAUDRATE_TABLE.
This patch add the support of higher baudrates on STMicroelectronics
boards with ST-LINK.
Cc: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Set the environment variable "console", used in extlinux.conf file when it
is generated by YOCTO distribution with:
UBOOT_EXTLINUX_CONSOLE ??= "console=${console},${baudrate}"
With these 2 variables, U-Boot give dynamically the used console and
baudrate in the Linux kernel bootargs.
For the STMicroelectronics boards, the used console is ttySTM0.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add missing \n at the end of the error trace
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
