So far u-boot only load SNSR25C for TMU main probe (probe 0). However,
kernel enables two probes. So it also needs to set default SNSR25C of
TCALIV1 for blank samples.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MP thermal which has two probes and supports temperature range
from -40 to 125. The driver still uses default 1p HW
calibration at 25C and loads calibration parameters from fuse.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Like iMX8MM, iMX8MN also needs SW to load TMU TASR and TCALIV registers
value from fuse before enabling TMU calibration. Otherwise the calibration
is not exact.
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On iMX8MM, the default value of TMU registers TCALIV and TASR need
be loaded from fuse. HW won't do this, it expect SW loads them before
using TMU.
Reviewed-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Support i.MX8MP thermal which has two probes and supports
temperature range from -40 to 125. Still uses default 1p HW
calibration at 25C and loads calibration parameters from fuse.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On iMX8MM, the V flag in TRISTR register only reflect the state of SNSR
value, not the calibrated TEMP value. So checking this flag is not
reliable. Per IC suggestion, change to read the TEMP/AVG_TEMP directly
and check whether it in valid range 10-125C.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When the temperature is out of sensor's range, the Valid bit won't be
set in TRITSR register. So the polling loop won't go out.
Change the codes to retry 10 times with 100ms interval for the Valid bit.
If the timeout, we give a warning for the invalid data.
Modifed from Ye's NXP patch
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MM TMU needs to load some registers from fuse, this is arch
dependent operation and may vary on different platforms. So add
a interface for arch level initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The analog sensors on iMX8MM are new, used for 14LPP process. So the
Temperature Sensor Monitoring Unit (TMU) has some change accordingly.
We use version 2 in TMU driver to represent the new TMU, so the one
driver can service for both i.MX8MQ/M.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The driver is ported form Linux Kernel and support driver model.
Users need to provide the tmu node and sensors nodes in DTB.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement the read_rom_hwaddr callback to load MAC address from fuse
for imx8m platforms.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
imx_get_mac_from_fuse is used to load MAC address from fuse. On imx8mp,
we have two different ENET controllers and both need to call this
function. So decouple its declare from fec driver.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement the callbacks to get phy mode interface and txclk
rate configuration.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add dwc eqos for imx support.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add RX delay enable support for RTL8211F PHY.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For dual ethernet controllers, the HW design may connect ETH phys to
one MDIO ports. So two different ethernet drivers have to share MDIO bus.
Since two ethernet drivers are independent, we can't ensure their probe
order.
To resolve this problem, introduce an eth phy generic driver and uclass.
After eth-uclass binds, we search the mdio node and binds the phy node
with the eth-phy-generic driver.
When one eth driver get its phy device, the parent of phy device will
probe prior than phy device. So this ensure the eth driver ownes the
MDIO bus will be probed before using its MDIO.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If a pad is not owned by current partition we should not set its
pinmux.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add fuse check for fec. If the fuse indicates the module
will not work in the SoC, let's fail the initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add fuse check for USB. If the fuse indicates the module
will not work in the SoC, let's fail the initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add fuse check for I2C. If the fuse indicates the module
will not work in the SoC, let's fail the initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There are different parts from one SoC. Take i.MX6ULL for example,
some part might not have ENET, some might have; some might not have
USB, some might have. The information could be got from OCOTP,
to make one image support the different parts, we need runtime
disable linux kernel dts node and uboot driver probe if the
corresponding module not exists in the part.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add initial support for Technexion Pico-iMX8MQ SoM on PicoPI carrier
board. Currently working is ethernet, serial, eMMC. DT is imported
from Linux 5.4.28 ("462afcd6e7ea") .
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Both the nolog as well as the syslog tests were not found by Python
function generate_ut_subtest() due to not following the nameing
requirements imposed by the regular expression used to find linker
generated list entries in file u-boot.sym.
Adjust the naming of test functions.
With the patch the following tests are executed successfully for
sandbox_defconfig:
test/py/tests/test_ut.py::test_ut[ut_log_syslog_debug] PASSED
test/py/tests/test_ut.py::test_ut[ut_log_syslog_err] PASSED
test/py/tests/test_ut.py::test_ut[ut_log_syslog_info] PASSED
test/py/tests/test_ut.py::test_ut[ut_log_syslog_nodebug] PASSED
test/py/tests/test_ut.py::test_ut[ut_log_syslog_notice] PASSED
test/py/tests/test_ut.py::test_ut[ut_log_syslog_warning] PASSED
The nolog tests are only executed if CONFIG_LOG=n and
CONFIG_CONSOLE_RECORD=y.
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Strict naming conventions have to be followed for Python function
generate_ut_subtest() to collect C unit tests to be executed via
command 'ut'.
Describe the requirements both on the C as well on the Python side.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Deciding whether to compile the env_sf_save() function based solely on
CONFIG_SPL_BUILD is wrong: For U-Boot proper, it leads to a build
warning in case CONFIG_CMD_SAVEENV=n (because the initialization of
the .save member is guarded by CONFIG_CMD_SAVEENV, while the
env_sf_save() function is built if !CONFIG_SPL_BUILD - and even
without the CONFIG_CMD_SAVEENV guard, the env_save_ptr() macro would
just expand to NULL, with no reference to env_sf_save visible to the
compiler). And for SPL, when one selects CONFIG_SPL_SAVEENV, one
obviously expects to actually be able to save the environment.
The compiler warning can be fixed by using a "<something> ?
env_sf_save : NULL" construction instead of a macro that just eats its
argument and expands to NULL. That way, if <something> is false,
env_sf_save gets eliminated as dead code, but the compiler still sees
the reference to it.
For <something>, we can use CONFIG_IS_ENABLED(SAVEENV), which is true
precisely:
- For U-Boot proper, when CONFIG_CMD_SAVEENV is set (because
CONFIG_SAVEENV is a hidden config symbol that gets set if and only
if CONFIG_CMD_SAVEENV is set).
- For SPL, when CONFIG_SPL_SAVEENV is set.
As a bonus, this also removes quite a few preprocessor conditionals.
This has been run-time tested on a mpc8309-derived board to verify
that saving the environment does indeed work in SPL with these patches
applied.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The reset_sata should reset the sata device info and free the
probe_ent memory. Otherwise, it will cause memory leak if we
init the sata again.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix coverity issue CID 43665: Free of address-of expression (BAD_FREE)
incorrect_free: free frees incorrect pointer pp.
pp points the port array field of struct ahci_uc_priv, should not free it.
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix coverity issue CID 3261683: Wrong operator used
(CONSTANT_EXPRESSION_RESULT) operator_confusion:
({...; __v;}) | 67108864 is always 1/true regardless of the values
of its operand. This occurs as the logical operand of !
When DIAG_X is set, the PHY COMINIT signal is detected, so
should use '&' to check whether it is set.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix coverity issue CID 3606684: Resource leak (RESOURCE_LEAK)
leaked_storage: Variable uc_priv going out of scope leaks the storage it points to
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This series contains bug fixes and code simplifications.
Following clarification in the discussion of the EBBR specification
device trees will be passed as EfiACPIReclaimMemory to UEFI applications.
-----BEGIN PGP SIGNATURE-----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=PVDs
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc2-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc2-3
This series contains bug fixes and code simplifications.
Following clarification in the discussion of the EBBR specification
device trees will be passed as EfiACPIReclaimMemory to UEFI applications.
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
The commit e89f8aae3d ("treewide: Migrate CONFIG_SYS_ALT_MEMTEST to Kconfig")
setup correct dependency on MEMTEST that's why there is no reason to enable
enable alternate memtest without mtest command.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no real need to exactly define space for saving patterns for
alternate memory test. It is much easier to allocate space on the stack and
use it instead of trying to find out space where pattern should be saved.
For example if you want to test the whole DDR memory you can't save patter
to DDR and you need to find it out. On Xilinx devices DDR or OCM addresses
were chosen but that means that OCM needs to be mapped and U-Boot has
access permission there.
It is easier to remove this limitation and simply save it on stack because
it is very clear that memory test can't rewrite U-Boot and U-Boot has also
full access to memory where runs from.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Move CONFIG_SYS_MTDPARTS_RUNTIME into Kconfig done by moveconfig.py.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Since pkcs7_parse_message() returns an error pointer, we must not
check for NULL. We have to explicitly set msg to NULL in the error
case, otherwise the call to pkcs7_free_message() on the goto err
path will assume it's a valid object.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Add missing include linux/err.h
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
