Enabling the domain clock is performed by the sysc interconnect target
module driver during the video device probing.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
The previous version of am335x-fb.c contained the functionalities of two
drivers that this patch has split. It was a video type driver that used
the same registration compatible string that now registers a panel type
driver. The proof of this is that two compatible strings were referred
to within the same driver.
There are now two drivers, each with its own compatible string,
functions and API.
Furthermore, the panel driver, in addition to decoding the display
timings, is now also able to manage the backlight.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch adds a function to get display timings from the device tree
node attached to the device.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
The TI PWMSS driver is a simple bus driver for providing clock and power
management for the PWM peripherals on TI AM33xx SoCs, namely eCAP,
eHRPWM and eQEP.
For DT binding details see Linux doc:
- Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Enhanced high resolution PWM module (EHRPWM) hardware can be used to
generate PWM output over 2 channels. This commit adds PWM driver support
for EHRPWM device present on AM33XX SOC.
The code is based on the drivers/pwm/pwm-tiehrpwm.c driver of the Linux
kernel version 5.9-rc7.
For DT binding details see:
- Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
Signed-off-by: Dario Binacchi <dariobin@libero.it>
The prescaler (PTV) setting must be taken into account even when the
timer input clock frequency has been set.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
The __of_translate_address routine translates an address from the
device tree into a CPU physical address. A note in the description of
the routine explains that the crossing of any level with
since inherited from IBM. This does not happen for Texas Instruments, or
at least for the beaglebone device tree. Without this patch, in fact,
the translation into physical addresses of the registers contained in the
am33xx-clocks.dtsi nodes would not be possible. They all have a parent
with #size-cells = <0>.
The CONFIG_OF_TRANSLATE_ZERO_SIZE_CELLS symbol makes translation
possible even in the case of crossing levels with #size-cells = <0>.
The patch acts conservatively on address translation, except for
removing a check within the of_translate_one function in the
drivers/core/of_addr.c file:
+
ranges = of_get_property(parent, rprop, &rlen);
- if (ranges == NULL && !of_empty_ranges_quirk(parent)) {
- debug("no ranges; cannot translate\n");
- return 1;
- }
if (ranges == NULL || rlen == 0) {
offset = of_read_number(addr, na);
memset(addr, 0, pna * 4);
debug("empty ranges; 1:1 translation\n");
There are two reasons:
1 The function of_empty_ranges_quirk always returns false, invalidating
the following if statement in case of null ranges. Therefore one of
the two checks is useless.
2 The implementation of the of_translate_one function found in the
common/fdt_support.c file has removed this check while keeping the one
about the 1:1 translation.
The patch adds a test and modifies a check for the correctness of an
address in the case of enabling translation also for zero size cells.
The added test checks translations of addresses generated by nodes of
a device tree similar to those you can find in the files am33xx.dtsi
and am33xx-clocks.dtsi for which the patch was created.
The patch was also tested on a beaglebone black board. The addresses
generated for the registers of the loaded drivers are those specified
by the AM335x reference manual.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Tested-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch moves the clk-ti-sci.c file to the 'ti' directory along with
all the other TI's drivers, and renames it clk-sci.c.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
This minimal driver is only used to bind child devices.
For DT binding details see Linux doc:
- Documentation/devicetree/bindings/arm/omap/prcm.txt
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Until now the clkctrl clocks have been enabled/disabled through platform
routines. Thanks to this patch they can be enabled and configured directly
by the probed devices that need to use them.
For DT binding details see Linux doc:
- Documentation/devicetree/bindings/clock/ti-clkctrl.txt
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Up till this commit passing NULL as input parameter was allowed, but not
handled properly. When a NULL parameter was passed to the function a data
abort was raised.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch adds support for TI gate clock binding. The code is based on
the drivers/clk/ti/gate.c driver of the Linux kernel version 5.9-rc7.
For DT binding details see:
- Documentation/devicetree/bindings/clock/ti/gate.txt
Signed-off-by: Dario Binacchi <dariobin@libero.it>
The patch adds support for TI divider clock binding. The driver uses
routines provided by the common clock framework (ccf).
The code is based on the drivers/clk/ti/divider.c driver of the Linux
kernel version 5.9-rc7.
For DT binding details see:
- Documentation/devicetree/bindings/clock/ti/divider.txt
Signed-off-by: Dario Binacchi <dariobin@libero.it>
The digital phase-locked loop (DPLL) provides all interface clocks and
functional clocks to the processor of the AM33xx device. The AM33xx
device integrates five different DPLLs:
* Core DPLL
* Per DPLL
* LCD DPLL
* DDR DPLL
* MPU DPLL
The patch adds support for the compatible strings:
* "ti,am3-dpll-core-clock"
* "ti,am3-dpll-no-gate-clock"
* "ti,am3-dpll-no-gate-j-type-clock"
* "ti,am3-dpll-x2-clock"
The code is loosely based on the drivers/clk/ti/dpll.c drivers of the
Linux kernel version 5.9-rc7.
For DT binding details see:
- Documentation/devicetree/bindings/clock/ti/dpll.txt
Signed-off-by: Dario Binacchi <dariobin@libero.it>
The driver manages a register-mapped multiplexer with multiple input
clock signals or parents, one of which can be selected as output. It
uses routines provided by the common clock framework (ccf).
The code is based on the drivers/clk/ti/mux.c driver of the Linux
kernel version 5.9-rc7.
For DT binding details see:
- Documentation/devicetree/bindings/clock/ti/mux.txt
Signed-off-by: Dario Binacchi <dariobin@libero.it>
It returns the rate which will be set if you ask clk_set_rate() to set
that rate. It provides a way to query exactly what rate you'll get if
you call clk_set_rate() with that same argument.
So essentially, clk_round_rate() and clk_set_rate() are equivalent
except the former does not modify the clock hardware in any way.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
There have been several changes to the am33xx.dtsi, so this patch
re-syncs it with Linux.
Let's add proper interconnect hierarchy for l4 interconnect instances
with the related ti-sysc interconnect module data as documented in
Documentation/devicetree/bindings/bus/ti-sysc.txt of the Linux kernel.
With l4 interconnect hierarchy and ti-sysc interconnect target module
data in place, we can simply move all the related child devices to their
proper location and enable probing using ti-sysc.
The am33xx-clock.dtsi file is the same as that of the Linux kernel,
except for the reg property of the node l4-wkup-clkctrl@0.
As for the am33xx.dtsi file, all the devices with drivers not yet
implemented and those I was able to test with this patch have been moved
to am33xx-l4.dtsi. In case of any regressions, problem devices can be
reverted by moving them back and removing the related interconnect
target module node.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
We can handle the sysc interconnect target module in a generic way for
many TI SoCs. Initially let's just enable domain clocks before the
children are probed.
The code is loosely based on the drivers/bus/ti-sysc.c of the Linux
kernel version 5.9-rc7.
For DT binding details see:
- Documentation/devicetree/bindings/bus/ti-sysc.txt
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Add support for PRUSS SYSC type:
The PRUSS module has a SYSCFG which is unique. The SYSCFG has two
additional unique fields called STANDBY_INIT and SUB_MWAIT in addition
to regular IDLE_MODE and STANDBY_MODE fields. Add the bindings for this
new sysc type.
Add support for MCAN on dra76x:
The dra76x MCAN generic interconnect module has a its own format for the
bits in the control registers.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Export routines that can be used by other drivers avoiding duplicating
code.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
As more and more LINUX drivers are modified to use asynchronous probing
instead of synchronous probing, relying on device names being equal in
U-Boot and LINUX is not possible anymore. This is also true for block
device names like mmc0, mmc1 ect.
With LINUX kernel commit a1a4891 the probing type for the sdhci-omap
driver has been set to asynchronous mode too (probe_type is now
PROBE_PREFER_ASYNCHRONOUS).
In the case of the PDU001 board this results in the devices mmc0 and
mmc1 being swapped between U-Boot and LINUX. Device mmc0 in U-Boot
becomes mmc1 in LINUX an vice versa. Hence using device name identifiers
with LINUX kernel parameter root does not work anymore.
This patch changes the LINUX kernel boot parameter root to use the
pseudo (since we use MBR not GPT) partition UUID to locate the partition
hosting the root file system.
Signed-off-by: Felix Brack <fb@ltec.ch>
Update the ddr settings to use the DDR reg config tool rev 0.5.0.
This enables 4266MTs DDR configuration.
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Kevin Scholz <k-scholz@ti.com>
McSPI IP provides per CS specific speed and mode selection. Therefore it
is possible to apply these settings only after CS is known. But
set_speed and set_mode can be called without bus being claimed, this
would lead driver to set up wrong CS (or previously used CS).
Fix this by apply set_speed and set_mode only if bus is already claimed.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
struct ti_qspi_priv->max_hz is declared as unsigned int, so the following
error path check will always be false, even when "spi-max-frequency"
property is invalid/missing:
priv->max_hz = fdtdec_get_int(blob, node, "spi-max-frequency", -1);
if (priv->max_hz < 0) {
...
}
Replace the fdtdec call with dev_read_u32_default() and use 0 as the
default value. Error out if max_hz is zero.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
The value of input pin for bank > 0 is always 0 for input subcommand.
The reason is that gpio_bank variable is computed only for invert and
output subcommands (it depends on number of arguments). The default
value of zero causes to shift the mask away for banks > 0.
Please note that info subcommand works as expected, because the input
pin values are accessed differently.
Fixes: 61c1775f16 ("gpio: tca642x: Add the tca642x gpio expander driver")
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
In include/dfu.h, if CONFIG_SYS_DFU_MAX_FILE_SIZE is not defined then it is
defined as CONFIG_SYS_DFU_DATA_BUF_SIZE. This is 128 KiB for a53 core and
20 KiB for r5 core. If a larger file is transferred using dfu then it
fails.
CONFIG_SYS_DFU_DATA_BUF_SIZE can not be increased as there is not enough
heap memory to be allocated for the buffer in case of R5 spl.
Fix this by defining CONFIG_SYS_DFU_MAX_FILE_SIZE as the default
CONFIG_SYS_DFU_DATA_BUF_SIZE value.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
The sequence number assigned for USB subsystem in a uclass is dependent on
the order of occurrence in the device tree. If the dr_mode of USB3SS0
controller is varied then the sequence number of USB3SS1 controller also
changes. If aliases are added then sequence numbers are assigned using the
alias number. This makes the sequence number of USB3SS1 controller
independent of USB3SS0 controller's dr_mode.
Therefore, add aliases to fix the sequence number assigned to the USB
subsystems.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
It has been observed that setting SERDES0 lane mux to USB prevents USB 2.0
operation on USB0. Setting SERDES0 lane mux to non-USB when USB0 is used in
USB 2.0 only mode solves this issue. However, for USB3.0+2.0 operation this
issue is not present.
Implement this workaround by writing 1 to LANE_FUNC_SEL field in
CTRLMMR_SERDES0_CTRL register.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
On the XEA board (imx28) one needs in the SPL support for GPIO, MMC and
SPI. Two last ones are necessary for booting the device. The GPIO support
allows deciding which medium will be used. For example the GPIO DTS node
(gpio@0 at imx28.dtsi) has pinctrl parent (pinctrl@80018000) for which we
don't need driver asigned for correct operation.
In the spl/dts/dt-platdata.c the gpio@0 has index 4 and its parent -
pinctrl@80018000 has index 5.
In the bind_drivers_pass() function (at drivers/core/lists.c) call to
device_bind_by_name() for `fsl_imx23_pinctrl` returns -2, which is
expected.
With current setup - when the SPL_OF_PLATDATA_PARENT=y
The gpio@0 node with index 4 is skipped as its parent with 5 is not yet
bound. It cannot be as we don't need and provide the driver for it.
As a result the gpio@0 is never bound and we end up with bricked board in
the SPL stage.
When CONFIG_SPL_OF_PLATDATA_PARENT is NOT set, all entries from
spl/dts/dt-platdata.c are scanned in ascending index order, so gpio@0 is
properly initialized. For `fsl_imx_pinctrl` we simply check 10 times if
the driver for is available (which is not) and exit.
As a result the GPIOs are initialized and can be used in early SPL stage.
This commit fixes XEA regression introduced with e41651fffd.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The usage of the preboot feature is now controlled via a separate Kconfig
option - namely CONFIG_USE_PREBOOT.
It must be enabled for preboot code executing commands now defined in
CONFIG_PREBOOT (also moved to the Kconfig).
After defining both CONFIG_USE_PREBOOT and CONFIG_PREBOOT in
imx28_xea_defconfig the define of CONFIG_PREBOOT shall be removed from
xea.h as it is redundant.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
On the imx287 pin GPMI_WRN (GPIO0_25) no PullUP is available that can be
enabled.
To get the same behavior for both boot select pins (i.e. GPIO0_2{35})
disable pull UPs on both.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
SPI flash on this machine is located on bus 1, default to using bus 1
for SPI flash and stop aliasing it to bus 0.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Fixes: c4cea2bb ("rockchip: Enable building a SPI ROM image on bob")
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
-----BEGIN PGP SIGNATURE-----
iFsEABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX/ROlgAKCRDKSWXLKUoM
IRC5AIkBzg4Sz8fQgdCiOK89k7tdFKMAnA9SYhgm4TSCzffZCJwnm78QoGAC
=4FnY
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.04
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Since GPIO_ACTIVE_HIGH is defined as 0, this change only increases the
correctness of the DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Due to a change in gpiolib-of.c, setting flags to GPIO_ACTIVE_LOW and
using output-low DT property leads to the GPIO being set high instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
Some of these tests don't actually check anything. Add a few more checks
to complete the tests.
Also add a simple scan test that does the basics.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move the tests related to scanning into their own class, updating them
to avoid using dtb_platdata as a pass-through.
Signed-off-by: Simon Glass <sjg@chromium.org>
Before expanding the scanning features any more, move this into a separate
file. This will make it easier to maintain in the future. In particular,
it reduces the size of dtb_platdata.py and allows us to add tests
specifically for scanning, without going through that file.
The pieces moved are the Driver class, the scanning code and the various
naming functions, since they mostly depend on the scanning results.
So far there is are no separate tests for src_scan. These will be added
as new functionality appears.
This introduces no functional change.
Signed-off-by: Simon Glass <sjg@chromium.org>
