These functions should not modify the device. Convert them to const so
that callers don't need to cast if they have a const udevice *.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add device table for new Micron SPI NAND devices, which have multiple
dies.
Also, enable support to select the dies.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Add SPINAND_HAS_CR_FEAT_BIT flag to identify the SPI NAND device with
the Continuous Read mode.
Some of the Micron SPI NAND devices have the "Continuous Read" feature
enabled by default, which does not fit the subsystem needs.
In this mode, the READ CACHE command doesn't require the starting column
address. The device always output the data starting from the first
column of the cache register, and once the end of the cache register
reached, the data output continues through the next page. With the
continuous read mode, it is possible to read out the entire block using
a single READ command, and once the end of the block reached, the output
pins become High-Z state. However, during this mode the read command
doesn't output the OOB area.
Hence, we disable the feature at probe time.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Add device table for M79A and M78A series Micron SPI NAND devices.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Add the SPI NAND device MT29F2G01ABAGD series number, size and voltage
details as a comment.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
In order to add new Micron SPI NAND devices, we generalized the OOB
layout structure and function names.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Some boards don't care about the ordering of ACPI code fragments. Change
the warning to a debug message.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds a UCLASS_SYSRESET sysreset driver for the Octeon SoC
family.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The types of "offset" and "size" of "struct mtd_partition" are uint64_t,
while mtd_parse_partitions() uses int to work with these values. When
the offset reaches 2GB, it is interpreted as a negative value, which
leads to error messages like
mtd: partition "<partition name>" is out of reach -- disabled
eg. when using the "ubi part" command.
Fix this by using uint64_t for cur_off and cur_sz.
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Some code was not converted by coccinelle, somehow.
I manually fixed up the remaining, and comments, README docs.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
[trini: Add arch/arm/mach-davinci/include/mach/sdmmc_defs.h and
include/fdt_support.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
- New timer API to allow delays with a 32-bit microsecond timer
- Add dynamic ACPI structs (DSDT/SSDT) generations to the DM core
- x86: Enable ACPI table generation by default
- x86: Enable the copy framebuffer on Coral
- x86: A few fixes to FSP2 with ApolloLake
- x86: Drop setup_pcat_compatibility()
- x86: Primary-to-Sideband Bus minor fixes
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXxCxWw8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76bPyACcDZ8gD9jf1P/Zh+7kqrGdIWwURF8AnAiEtNnu
FhE/WQQj4mAEWE4F2bFE
=7ceG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200716' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
i.MX for 2020.10
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
This should ideally be used by all x86 boards in U-Boot. Enable it by
default. If some boards don't use it, the cost is small.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The FSP-S changes the ITSS priorities. The code that tries to save it
before running FSP-S and restore it afterwards does not work as U-Boot
relocates in between the save and restore. This means that the driver
data saved before relocation is lost and the new driver just sees zeroes.
Fix this by allocating space in the relocated memory for the ITSS data.
Save it there and access it from the driver after relocation.
This fixes interrupt handling on coral.
Also drop the log_msg_ret() in irq_first_device_type() since this function
can be called speculatively in places where we are not sure if there is
an interrupt controller of that type. The resulting log errors are
confusing when there is no error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
These registers need to be accesses from ACPI code, so move them to the
header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The P2SB bus needs to be hidden in some cases so that it does not get
auto-configured by Linux. Add a method for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Tested-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Update the PCI driver to generate ACPI information so that Linux has the
full information about each I2C bus.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
[bmeng: Correct one typo in dw_i2c_gen_speed_config() comments]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add a few of these calls to make it easier to see where an error occurs,
if CONFIG_LOG_ERROR_RETURN is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add debugging for a few more values and also use log to show return values
when something goes wrong. This makes it easier to see the root cause.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Implement the method that converts a GPIO into the form used by ACPI, so
that GPIOs can be added to ACPI tables.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is in the device tree now, so drop the unnecessary field here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the itss is probed in the ofdata_to_platdata() method. This is
incorrect since itss is a child of p2sb which itself needs to probe the
pinctrl device. This means that p2sb is effectively not probed when the
itss is probed, so we get the wrong register address from p2sb.
Fix this by moving the itss probe to the correct place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Add a Kconfig to control whether pinctrl is represented as a single ACPI
device or as multiple devices. In the latter case (the default) we should
return the pin number relative to the pinctrl device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
At present we can query the offset of a pinctrl register within the p2sb.
For ACPI we need to get the actual address of the register. Add a function
to handle this and rename the old one to more accurately reflect its
purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
This chip is used on coral and we need to generate ACPI tables for sound
to make it work. Add a driver that does just this (i.e. at present does
not actually support playing sound).
Signed-off-by: Simon Glass <sjg@chromium.org>
[bmeng: Use the correct acpi_irq_polarity enum number]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This chip is used on coral and we need to generate ACPI tables for sound
to make it work. Add a driver that does just this (i.e. at present does
not actually support playing sound).
Signed-off-by: Simon Glass <sjg@chromium.org>
Write required information into the SSDT to describe the SD card
card-detect pin. Since the required GPIO properties are not present in
the device-tree binding, set them manually for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Intel Non-High-Definition-Audio Link Table (NHLT) table describes the
audio codecs and connections in a system. Various devices can contribute
information to produce the table.
Add core support for this, based on a structure which is built up through
calls to the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Some devices such as GPIO need to override the normal path that would be
generated by driver model. Add a device-tree property for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Add a command that shows the individual blocks of data generated by each
device, effectively splitting the full table into its component parts.
This can be helpful for debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For many device types it is possible to figure out the name just by
looking at its uclass or parent. Add a function to handle this, since it
allows us to cover the vast majority of cases automatically.
However it is sometimes impossible to figure out an ACPI name for a device
just by looking at its uclass. For example a touch device may have a
vendor-specific name. Add a new "acpi,name" property to allow a custom
name to be created.
With this new feature we can drop the get_name() methods in the sandbox
I2C and SPI drivers. They were only added for testing purposes. Update the
tests to use the new values.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some devices need to inject extra code into the Differentiated System
Descriptor Table (DSDT). Add a method to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct one typo in inject_dsdt() comments]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add a /chosen property to control the order in which the data appears
in the SSDT. This allows matching up U-Boot's output from a dump of the
known-good data obtained from within Linux.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to be able to control the order of data written to the SSDT
so that we can compare the output against known-good kernel dumps.
Add code to record each item that is added along with the device that
added it. That allows us to reorder things later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some devices need to generate code for the Secondary System Descriptor
Table (SSDT). Add a method to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a function to write a SPI descriptor to the generated ACPI code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a function to write a GPIO descriptor to the generated ACPI code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When generating ACPI tables we need to convert GPIOs in U-Boot to the ACPI
structures required by ACPI. This is a SoC-specific conversion and cannot
be handled by generic code, so add a new GPIO method to do the conversion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When generating ACPI tables we need to convert IRQs in U-Boot to the ACPI
structures required by ACPI. This is a SoC-specific conversion and cannot
be handled by generic code, so add a new IRQ method to do the conversion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This always has a fixed ACPI name so add it as a driver function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In Intel's documentation the term P2SB stands for "Primary to Sideband
Bridge".
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
After "4b969deac0 watchdog: imx: Add DM support", the imx watchdog
can be started by wdt command. But the imx watchdog driver only
support start with the default timeout.
This commit adds the support for setting the timeout which pass from
the wdt command into the imx watchdog. If the timeout out of the
valid range(0.5~128s), start the watchdog with a timeout within the
valid range and the timeout is the one which closest to the passed
timeout.
Signed-off-by: Yuezhang.Mo <yuezhang.mo@sony.com>
Reviewed-by: Andy.Wu <Andy.Wu@sony.com>
Reviewed-by: stefano Babic <sbabic@denx.de>
Quoting Ye Li from NXP:
"We have confirmed with PMIC team, 0x35 is used only on early chips
and not used any more. 0x25 is the final address."
Fix it by merging power_pca9450a_init and power_pca9450b_init into one
function power_pca9450_init.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Current mxc_gpio DM driver allocates the platdata in bind function to
handle both OF_CONTROL enabled case and disabled case. This implementation
puts the devfdt_get_addr in bind, which introduces much overhead especially
in board_f phase.
Change the driver to a common way for handling the cases by using
ofdata_to_platdata and using DM framework to allocate platdata.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add SCFW API sc_misc_get_boot_container to get current boot container
set index.
The index value returns 1 for primary container set, 2 for secondary
container set.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
i.MX platforms provide large AHB mapped space for QSPI, each
controller has 256MB. However, current driver only maps small
size (AHB buffer size) of AHB space, this implementation
causes i.MX failed to boot M4 with QSPI XIP image.
Add config CONFIG_FSL_QSPI_AHB_FULL_MAP (default enabled for i.MX)
to address above problem.
When the config is set:
1. Full AHB space is divided to each CS.
2. A dedicated LUT entry is used for AHB read only.
3. The MODE instruction in LUT is replaced to standard ADDR instruction
4. The address in spi_mem_op is used to SFAR and AHB read
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Add compatible string and driver data for i.MX7ULP.
Meanwhile, the address set to SFA1AD/SFA2AD/SFB1AD/SFB2AD should
align with 1KB, because the lowest 10 bits are reserved by the
registers definition.
For i.MX7ULP which has only 128Bytes AHB buffer, must align it
when setting the registers and selecting cs.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
As per the SD physical layer specification version 7.10, erase
command (CMD38) and stop transmission command (CMD12) will generate
R1b response.
R1b = R1 + busy signal
A non-zero value after the R1 response indicates card is ready for
next command.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Erase block start address (CMD32) and erase block end address (CMD33)
command will generate R1 response for mmc SPI mode.
R1 response is 1 byte long for mmc SPI, so assign 1 byte as a response
for this commands.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Send status command (CMD13) will send R1 response under SD mode
but R2 response under SPI mode.
R2 response is 2 bytes long, so read 2 bytes for mmc SPI mode
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
The content of ssr is useful only for erase operations.
This saves erase time.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
R1 response is 1 byte long for mmc SPI commands as per the updated
physical layer specification version 7.10.
So correct the resp and resp_size for existing commands
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
When variable i will become 0, while(i--) loop breaks but variable i will
again decrement to -1 because of i-- and that's why below condition
"if (!i && (r != resp_match_value)" will never execute, So doing "i--"
inside of while() loop solves this problem.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
We use non-dm code to configure the clk settings in order to simplify
dm clk driver in future, so remove the duplicated code from clk driver
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add clocks for FEC and flexspi, and add set parent clock callback,
so DTS can assign clocks
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add USB relevant clocks to support usb clock settings for both
DM USB host and gadget drivers
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add set clock parent support.
Add ENET and flexspi related clocks to support assigned clocks
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The soc info without initialization value should be put into
data section. The driver could be used before relocation,
with it in BSS section could cause issue, since BSS section
is not initializated and it might overwrite other areas that
used by others, such as dtb.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The soc info without initialization value should be put into
data section. The driver could be used before relocation,
with it in BSS section could cause issue, since BSS section
is not initializated and it might overwrite other areas that
used by others, such as dtb.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The soc info without initialization value should be put into
data section. The driver could be used before relocation,
with it in BSS section could cause issue, since BSS section
is not initializated and it might overwrite other areas that
used by others, such as dtb.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add logic to automatically update umctl2's setting based
on phy training CDD value for rank to rank space issue
Acked-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Oliver Chen <Oliver.Chen@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
the DRAM Controller in i.MX8MP will support a feature called "Inline ECC".
This is supported for all 3 supported DRAM technologies (LPDDR4, DDR4 and
DDR3L). When this feature is enabled by software, the DRAM Controller
reserves 12.5% of DRAM capacity for ECC information, and presents only
the non-ECC portion (lower 87.5% of the installed capacity of DRAM) to
the rest of the SoC.
The DRAM memory can be divided into 8 regions so that if a use case only
requires ECC protection on a subset of memory, then only that subset of
memory need support inline ECC. If this occurs, then there is no
performance penalty accessing the non-ECC-protected memory (no need to
access ECC for this portion of the memory map). This is all configured
with the DRAM Controller.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The 'selfref_en' should be bit'0', so correct the setting to
enable the auto self-refresh.
Reviewed-by: Jian Li <jian.li@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There is no DDR_SS_GPR0 exits on i.MX8MN, so skip setting
this register on i.MX8MN.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In commit commit d2c05f50e1 ("mmc: omap_hsmmc: Set 3.3V for IO voltage")
was changed 3.0V IO voltage to 3.3V but it was not done on all places in
omap_hsmmc driver. That commit broke eMMC support on Nokia N900.
This patch fixes that problematic commit and changes 3.0V to 3.3V on all
remaining places in omap_hsmmc driver.
Fixes: d2c05f50e1 ("mmc: omap_hsmmc: Set 3.3V for IO voltage")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Faiz Abbas <faiz_abbas@ti.com>
We only request ring pairs via K3 DMA driver, switch to use the new
k3_ringacc_request_rings_pair() to simplify the code.
As a good side effect, all boot stages now use exposed RING mode which
avoid maintaining proxy mode for 32 bit R5 core.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
In K3 UDMA architecture, RX rings are associated with RX flows rather
than RX channels, therefore move the ring pointers to udma_rflow struct
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Encapsulate channel configuration in a separate struct so as to ease
resetting of these fields with memset() and also to increase readability
of the code.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
In preparation of adding more K3 SoCs, separate soc specific
initialization add a SoC specific initialization hook.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add new API k3_ringacc_request_rings_pair() to request pair of rings at
once, as in the most case Rings are used with DMA channels which required
to request pair of rings - one to feed DMA with descriptors (TX/RX FDQ) and
one to receive completions (RX/TX CQ). This will allow to simplify Ringacc
API users.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Move the free, occ, windex and rinfex under a struct.
We can use memset to zero them and it will allow a cleaner way to extend
the variables for duplex rings.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Update driver to use static PSIL endpoint Data instead of DT. This will
allow DT bindings to be in sync with kernel's DT.
Note that this patch breaks networking and OSPI boot as driver changes
are not backward compatible with existing DT. Subsequent commit will
update the DT to make it compatible with updated driver.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Much of PSIL endpoint configuration for a given SoC can be known at
compile time, therefore pass them for platform specific data instead of
DT.
Add per SoC's specific PSIL endpoint data. This is to bring driver in
sync with upstream DT.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Fixed delay 200us is not working in certain platforms. Change to
poll for reset completion status to have more reliable reset process.
Controller will set the rst_comp bit in intr_status register after
controller has completed its reset and initialization process.
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Radu Bacrau <radu.bacrau@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Always put the controller in reset, then take it out of reset.
This is to make sure controller always in reset state in both SPL and
proper Uboot.
This is preparation for the next patch to poll for reset completion
(rst_comp) bit after reset.
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Radu Bacrau <radu.bacrau@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This UART controller is integrated with a FIFO. Enable it.
You can put the next character into the FIFO while the transmitter
is sending out the current character. This works slightly faster.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Ensure the transmitter is empty when chaining the baudrate or any
hardware settings. If a character is remaining in the transmitter,
the console will be garbled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
After all, I am not a big fan of using a structure to represent the
hardware register map.
You do not need to know the entire register map.
Add only necessary register macros.
Use FIELD_PREP() instead of maintaining a pair of shift and mask.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit 1517126fda ("ARM: uniphier: select DM_ETH"), DM-based
drivers/net/smc911x.c is compiled, but it is never probed because the
parent node lacks the DM-based driver.
I need a skeleton driver to populate child devices (but the next commit
will move more hardware settings to the this driver).
I put this to drivers/bus/uniphier-system-bus.c because this is the
same path as the driver in Linux kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
patman support for Python3 on Ubuntu 14.04
new checkpatch check to avoid #ifdefs
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8InaQRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreazvAgAgqyvPY2o+BNHscrx9/6sEOHSAVty/D5t
SdaphzRezlJOWy9MC/ZyqyevZjogN7fgGNQVgh/I4BklIc/N5Omn68/+JWylSFVP
taJKiJD1IVSThTXGOMTxlDiTxY7NfVDUDjtFIpCDswBrnSJlX+2v/RsehUwVIrYn
NJwiRXd33IdS1vh1mqqNgwbZNBo+zGWn5LApq71vLSVkiQlmcpMG9FmYYRcg/AhG
3Xd2HB2ANcvb13fMMcwd3s4WPNYoiJvwjSHScNDUPEip7XeZNDiNeq4gC6d2Uw+J
zC3/vOCP3eRtAnr6syJ5QcGN/eeKwLtnTE+fOuOm6s5Y98po4iMykA==
=3fC5
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10jul20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
of-platdata: better phandle and compatible-string support
patman support for Python3 on Ubuntu 14.04
new checkpatch check to avoid #ifdefs
On build with 32 bit, there is a warning for int-to-pointer-cast.
Fix the int to pointer cast by using uintptr_t.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Some atypical users of xhci might need to manually reset their xHCI
controller before starting the HCD setup. Check if a reset controller
device is available to the PCI bus and trigger a reset.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
[mb: squash fix to only build xhci_reset_hw() if CONFIG_DM_BUS]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Raspberry Pi 4's co-processor controls some of the board's HW
initialization process, but it's up to Linux to trigger it when
relevant. Introduce a reset controller capable of interfacing with
RPi4's co-processor that models these firmware initialization routines as
reset lines.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This patch adds basic driver PCI Express controller found on Broadcom
set-top-box SoCs, e.g. BCM2711.
The code is based on Linux upstream driver (pcie-brcmstb.c) with MSI
handling removed. The inbound access memory region is not currently
parsed from dma-ranges DT property and a fixed 3GB region is used.
The patch has been tested on RPI4 board, i.e. on BCM2711 SoC with VL805
USB Host Controller.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Drop the nondm code from kirkwood_spi.c since there
is no board or any other code using for it.
Signed-off-by: Bhargav Shah <bhargavshah1988@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
In the current implementation, when dtoc parses a dtb to generate a struct
platdata it converts the information related to linked nodes as pointers
to struct platdata of destination nodes. By doing this, it makes
difficult to get pointer to udevices created based on these
information.
This patch extends dtoc to use struct driver_info when populating
information about linked nodes, which makes it easier to later get
the devices created. In this context, reimplement functions like
clk_get_by_index_platdata() which made use of the previous approach.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently when creating an U_BOOT_DEVICE entry a struct driver_info
is declared, which contains the data needed to instantiate the device.
However, the actual device is created at runtime and there is no proper
way to get the device based on its struct driver_info.
This patch extends struct driver_info adding a pointer to udevice which
is populated during the bind process, allowing to generate a set of
functions to get the device based on its struct driver_info.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to prepare for a new support of phandle when OF_PLATDATA is used
drop the const for struct driver_info as this struct will need to be
updated on runtime.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently when using OF_PLATDATA the binding between devices and drivers
is done trying to match the compatible string in the node with a driver
name. However, usually a single driver supports multiple compatible strings
which causes that only devices which its compatible string matches a
driver name get bound.
To overcome this issue, this patch adds the U_BOOT_DRIVER_ALIAS macro,
which generates no code at all, but allows an easy way to declare driver
name aliases. Thanks to this, dtoc could be improve to look for the driver
name based on its alias when it populates the U_BOOT_DEVICE entry.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using OF_PLATDATA, the bind process between devices and drivers
is performed trying to match compatible string with driver names.
However driver names are not strictly defined, and also there are different
names used when declaring a driver with U_BOOT_DRIVER, the name of the
symbol used in the linker list and the used in the struct driver_info.
In order to make things a bit more clear, rename the drivers names. This
will also help for further OF_PLATDATA improvements, such as checking
for valid driver names.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a fix for sandbox of-platdata to avoid using an invalid ANSI colour:
Signed-off-by: Simon Glass <sjg@chromium.org>
Compiling drivers/mtd/spi/sandbox.c fails when compiled with
CONFIG_LOG=n:
In file included from include/common.h:20,
from drivers/mtd/spi/sandbox.c:13:
drivers/mtd/spi/sandbox.c:295:15: error: format ‘%s’ expects argument of
type ‘char *’, but argument 7 has type ‘int’ [-Werror=format=]
295 | log_content(" cmd: transition to %s state\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/printk.h:37:21: note: in definition of macro ‘pr_fmt’
37 | #define pr_fmt(fmt) fmt
| ^~~
include/log.h:128:30: note: in expansion of macro ‘log_nop’
128 | #define log_content(_fmt...) log_nop(LOG_CATEGORY, \
| ^~~~~~~
drivers/mtd/spi/sandbox.c:295:3: note: in expansion of macro
‘log_content’
295 | log_content(" cmd: transition to %s state\n",
| ^~~~~~~~~~~
drivers/mtd/spi/sandbox.c:295:37: note: format string is defined here
295 | log_content(" cmd: transition to %s state\n",
| ~^
| |
| char *
| %d
Supply function sandbox_sf_state_name() independent of CONFIG_LOG.
Fixes: c3aed5db59 ("sandbox: spi: Add more logging")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable QE bit for ISSI flash chips.
QE enablement logic is similar to what Macronix
has, so reuse the existing code itself.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The spi bitbanging driver did not implement all spi modes properly. Add
code to support all spi modes, honoring soft_spi_set_mode() and
defaulting to spi mode 0. Previously, CPHA was implemented inversely
(defaulting to CPHA=1) and CPOL=1 was hardcoded.
Signed-off-by: Johannes Holland <johannes.holland@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- Add two- and three-argument versions of CONFIG_IS_ENABLED in
linux/kconfig.h
- Adds a new feature which supports copying modified parts of
the frame buffer to the uncached hardware buffer
- Enable the copy framebuffer on various x86 targets
Some PCI Express register offsets are currently defined in multiple
drivers, move them to a common header to avoid re-definitions and
as a pre-requisite for adding new PCIe driver.
While at it replace some spaces with tabs.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
In current code there is no cache flush after initializing the scratchpad
buffer array with the scratchpad buffer pointers. This leads to a failure
of the "slot enable" command on the rpi4 board (Broadcom STB PCIe
controller + VL805 USB hub) - the very first TRB transfer on the command
ring fails and there is a timeout while waiting for the command completion
event. After adding the missing cache flush everything seems to be working
as expected.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
i2c changes for v2020.10
- Add support for I2C controllers found on Octeon II/III and Octeon TX
TX2 SoC platforms.
- Add I2C controller support for Cortina Access CAxxxx SoCs
- new rtc methods, rtc command, and tests
- imx_lpi2c: Improve the codes to use private data
- stm32f7_i2c.c: Add new compatible "st,stm32mp15-i2c"
- stm32f7_i2c.c: Add Fast Mode Plus support
- pwm: Add PWM driver for SiFive SoC
Since the mdio code got upstreamed it is not possible
to activate network ports on CP110 Master and Slave.
The problem is in mvpp2_base_probe which is called for each
CP110 and it initializes the buffer area for descs and rx_buffers.
This should only happen once though and the bd space is actually
set to 0 after the first run of the function.
This leads to an error when the second CP110 tries the initialization
again and disables all network ports on this CP110.
This patch adds a static variable to check if the buffer area is
initialized only once globally.
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Measurements on actual hardware shown that the read ODT is early by 3
clocks. Adjust the calculation to avoid this.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[upstream https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell/pull/22]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
In the Armada 385 functional spec (MV-S109094-00 Rev. C) the read sample
delay fields are 5 bits wide. Use the correct bitmask of 0x1f when
extracting the value.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[upstream https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell/pull/22]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Update the video driver to support this feature and enable it on
minnowmax to speed up the display.
With this change, the time taken to print the environment to the display
without CONFIG_CONSOLE_SCROLL_LINES is reduced from over 13 seconds to
300ms, at 1280x1024.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update the video driver to support this feature and enable it on link.
Also remove the multi-line scrolling since normal scrolling is fast enough
now.
With this change, the time taken to print the environment to the display
without CONFIG_CONSOLE_SCROLL_LINES is reduced from about 930ms to 29ms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update the video driver to support this feature and enable it on samus.
Also remove the multi-line scrolling since normal scrolling is fast enough
now.
With this change, the time taken to print the environment to the display
without CONFIG_CONSOLE_SCROLL_LINES is reduced from about 430ms to 12ms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For PCI video devices that are not mentioned in the devicetree, U-Boot
does not bind a driver before relocation, since PCI is not fully probed
at that point. Furthermore it is possible for the video device to be on
a secondary bus which is not even scanned.
This is fine if the framebuffer is allocated in fixed memory, as it
normally is on x86. But when using this as a copy framebuffer, we also
need U-Boot to allocate its own cached framebuffer for working in. Since
the video driver is never bound before relocation, the framebuffer size
is never set and U-Boot does no allocation.
Add a new CONFIG option to reserve 16MB of memory for this eventuality.
This allows vesa devices to use the copy framebuffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present video_bottom is set to the bottom of each framebuffer when it
is allocated. This is not correct, since it should hold the bottom of the
entire area available for framebuffers.
Fix this by adding a private address in the uclass which keeps track of
the next available spot for a framebuffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
When using a copy framebuffer we need to tell the video subsystem its
address. U-Boot's normally allocated framebuffer is used as the working
buffer, but nothing is displayed until it is copied to the copy
framebuffer.
For this to work the video driver must request that a framebuffer be
allocated separately from the hardware framebuffer, so add a check for
that.
Also add a log category so that logging appears correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Enable this feature on sandbox by updating the SDL driver to have two
framebuffers.
Update the video tests to check that the copy framebuffer is kept in sync.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Adjust the bitmap code to sync to the copy framebuffer when done.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update the implementation to keep a track of what it changes in the frame
buffer and then tell the copy buffer about it. Use the special
vidconsole_memmove() helper so that memmove() operations are also
reflected in the copy buffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update the implementation to keep a track of what it changes in the frame
buffer and then tell the copy buffer about it. Use the special
vidconsole_memmove() helper so that memmove() operations are also
reflected in the copy buffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update the implementation to keep a track of what it changes in the frame
buffer and then tell the copy buffer about it. Use the special
vidconsole_memmove() helper so that memmove() operations are also
reflected in the copy buffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add a convenience function to call video_sync_copy() for a vidconsole.
Also add a memmove() helper, which does the memmove() as well as the sync.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update video_clear() to also sync to the copy framebuffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This framebuffer is separately mapped. Update the video post-probe
function to set this up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Some architectures use a cached framebuffer and flush the cache as needed
so that changes are visible. This is supported by U-Boot.
However x86 uses an uncached framebuffer with a 'write-combining' feature
to speed up writes. Reads are permitted but they are extremely expensive.
Unfortunately, reading from the frame buffer is quite common, e.g. to
scroll it. This makes scrolling very slow.
Add a new feature which supports copying modified parts of the frame
buffer to the uncached hardware buffer. This speeds up scrolling by at
least 10x on x86 so the extra complexity cost seems worth it.
As a starting point, add the Kconfig, update the video structures to keep
track of the buffer and add a function to do the copy.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present when the console is rotated 180 degrees it starts almost a
whole character to the left of the right edge (typically 7 pixels with
an 8-pixel-wide font). On a display which aligns with the font width,
this just wastes space. On a display that does not this can result in
x_frac going negative for the final character (the one on the left
side) and the overflow -EAGAIN check at the start of the function
failing.
Change the function to start at the rightmost pixel to fix these
problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The functions in this file do similar things but not always in the same
way. To make the code easier to read and compare, use a separate 'linenum'
variable in every function. This is then multiplied by the line length to
get the offset within the frame buffer to modify. Also use an 'x' variable
to hold the pixel position within that line. This is multipled by the
pixel size and added to the offset.
Also move the pbytes declaration up a little with the other long lines.
A side effect of splitting out these variables is that they are promoted
to int, i.e. a signed type, from the unsigned short used in the
vidconsole_priv struct. This would be necessary should any of the
variables go negative. At present this can actually happen in
console_putc_xy_2(), if the display width is not a multiple of the
character size (see next patch).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add a devicetree property to select a rotated console. This uses the same
encoding as vidconsole itself: 0=normal; 1=90 degrees clockwise, 2=upside
down, 3=90 degrees anticlockwise.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
At present these functions fail silently even when debugging, which is not
very helpful. Add a way to print a message to the serial output when an
error is detected.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adds a PWM driver for PWM chip present in SiFive's HiFive Unleashed SoC
This driver is simple port of Linux pwm sifive driver from Linux v5.6
commit: 9e37a53eb051 ("pwm: sifive: Add a driver for SiFive SoC PWM")
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Read SYSCFG bindings to set Fast Mode Plus bits if Fast Mode Plus
speed is selected.
Handle the stm32mp15 specific compatible to handle FastMode+
registers handling which is different on the stm32mp15 compared
to the stm32f7 or stm32h7.
Indeed, on the stm32mp15, the FastMode+ set and clear registers
are separated while on the other platforms (F7 or H7) the control
is done in a unique register.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add a new compatible "st,stm32mp15-i2c" introduced in Linux kernel v5.8
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
It's more natural that any write that happens to touch the reset
register should cause a reset, rather than just a write that starts at
that offset.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The current set method is broken; a simple test case is to first set
the date to something in April, then change the date to 31st May:
=> date 040412122020.34
Date: 2020-04-04 (Saturday) Time: 12:12:34
=> date 053112122020.34
Date: 2020-05-01 (Friday) Time: 12:12:34
or via the amending of the existing rtc_set_get test case similarly:
$ ./u-boot -T -v
=> ut dm rtc_set_get
Test: dm_test_rtc_set_get: rtc.c
expected: 31/08/2004 18:18:00
actual: 01/08/2004 18:18:00
The problem is that after each register write,
sandbox_i2c_rtc_complete_write() gets called and sets the internal
time from the current set of registers. However, when we get to
writing 31 to mday, the registers are in an inconsistent state (mon is
still 4), so the mktime machinery ends up translating April 31st to
May 1st. Upon the next register write, the registers are populated by
sandbox_i2c_rtc_prepare_read(), so the 31 we just wrote to mday gets
overwritten by a 1.
Fix it by writing all registers at once, and for consistency, update
the get method to retrieve them all with one "i2c transfer".
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
This simply consists of renaming the existing pcf2127_read_reg()
helper to follow the naming of the other
methods (i.e. pcf2127_rtc_<method name>) and changing the type of its
"len" parameter.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Similar to how the dm_rtc_{read,write} functions fall back to using
the {read,write}8 methods, do the opposite in the rtc_{read,write}8
functions.
This way, each driver only needs to provide either ->read8 or ->read
to make both rtc_read8() and dm_rtc_read() work - without this, a
driver that provides ->read() would most likely just duplicate the
logic here for implementing a ->read8() method in term of its ->read()
method. The same remarks of course apply to the write case.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Similar to dm_rtc_read(), introduce a helper that allows the caller to
write multiple consecutive 8-bit registers with one call. If the
driver provides the ->write method, use that, otherwise loop using
->write8.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Some users may want to read multiple consecutive 8-bit
registers. Instead of each caller having to implement the loop,
provide a dm_rtc_read() helper. Also, allow a driver to provide a
->read method, which can be more efficient than reading one register
at a time.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Current driver calls the devfdt_get_addr to get the base address
of lpi2c controller in each sub-functions. Since the devfdt_get_addr
accesses the DTB and translate the address, it introduces much
overhead.
Improve the codes to use private variable which has recorded the
base address from probe.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The offset at which the image to be loaded from NAND is located is
retrieved from the itb header. The presence of bad blocks in the area
of the NAND where the itb image is located could invalidate the offset
which must therefore be adjusted taking into account the state of the
sectors concerned.
cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
