The PCIe controller on the M2 Pro/Max is different from the one
found on earlier Apple SoCs. Some registers moved and te meaning
of the bits in some other registers changed. But they are still
similar enough to handle both controllers in the same driver.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Apple's M2 Pro/Max SoC are somewhat similar to the M1 Pro/Max but
need a tweaked memory map. USB, NVMe, UART and WDT are working
with the existing drivers.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
K3 GP devices allows booting the secure binaries on them by bypassing
the x509 header on them.
ATF and OPTEE firewalling required the rproc_load to be called before
authentication. This change caused the failure for GP devices that
strips off the headers. The boot vector had been set before the headers
were stripped off causing the runtime stripping to fail and stripping
becoming in-effective.
Separate out the secure binary check on GP/HS devices so that the
boot_vector could be stripped before calling rproc_load. This allows
keeping the authentication later when the cluster is on along with
allowing the stripping of the binaries in case of gp devices.
Fixes: 1e00e9be62 ("arm: mach-k3: common: re-locate authentication for atf/optee")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
When booting with HS silicon, the system firmware image is 278270, which
is slightly larger than currently allocated amount.
This can cause unexpected behavior if this overlap interferes with other
things in memory, so increase this with a slightly margin added as well
to avoid any boot issues that can appear after system firmware gets
loaded.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
In non-combined boot flow for K3, all the firewalls are locked by default
until sysfw comes up. Rom configures some of the firewall for its usage
along with the SRAM for R5 but the PSRAM region is still locked.
The K3 MCU Scratchpad for j721e was set to a PSRAM region triggering the
firewall exception before sysfw came up. The exception started happening
after adding multi dtb support that accesses the scratchpad for reading
EEPROM contents.
The commit changes R5 MCU scratchpad for j721e to an SRAM region.
Old Map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c40000 (approx)
│ STACK │
├─────────────────────────────────────┤ 0x41c85b20
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c85bfc
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x70000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41cf5bfc)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
New Map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c40000 (approx)
│ EMPTY │
├─────────────────────────────────────┤ 0x41c81920
│ STACK │
│ SPL_SIZE_LIMIT_PROVIDE_STACK=0x4000 │
├─────────────────────────────────────┤ 0x41c85920
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c859f0
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x70000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41cf59f0)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
├─────────────────────────────────────┤ 0x41cff9fc
│ NEW MCU SCRATCHPAD │
│ SYS_K3_MCU_SCRATCHPAD_SIZE = 0x200 │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
Fixes: ab977c8b91 ("configs: j721s2_evm_r5: Enable support for building multiple dtbs into FIT")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
[n-francis@ti.com: SRAM allocation addressing diagram]
Signed-off-by: Neha Francis <n-francis@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
K3 devices have runtime type board detection. Make the default defconfig
include the secure configuration. Then remove the HS specific config.
Non-HS devices will continue to boot due to runtime device type detection.
If TI_SECURE_DEV_PKG is not set the build will emit warnings, for non-HS
devices these can be ignored.
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
When building for secure devices using non-buildman based image generation
the signed tispl.bin file is called tispl.bin_HS. Also build the unsigned
tispl.bin file as expected.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Add trivial driver for the MXS AUART IP. This is the other UART IP
present in i.MX23 and i.MX28, used to drive the non-DUART ports.
Signed-off-by: Marek Vasut <marex@denx.de>
Update DDR timing file generated by DDR Config Tool
1. Dynamic refresh rate is set by default
2. The 3rd freq will be 625MTS based on power and performance better than 100MTS.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To avoid using static setting for ECC enabled DDR size, switch
to calculate DDR size from DDRC setting
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The rank setting flow should be updated to support multi
fsp config.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the DDR init flow for multi-setpoint support on i.MX93. A new
fsp_cfg struct need to be added in the timing file to store the diff
part of the DDRC and DRAM MR register for each setpoint.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add 625M bypass clock that may be used DRAM 625M
bypass mode support.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
change the ddr saved info to the last 16KB of the OCRAM.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
As the ddr timing info will be saved at the last 16KB of
the OCRAM, spl stack & bss base should be updated to avoid
conflict.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to DDRPHY errata, the Rank-to-Rank Spacing and tphy_rdcsgap
specification does not include the Critical Delay Difference (CDD) to
properly define the required rank-to-rank read command spacing after
executing PHY training firmware.
Following the errata workaround, at the end of data training, we get
all CDD values through the MessageBlock, then re-configure the DDRC
timing of WWT/WRT/RRT/RWT with comparing MAX CDD values.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Currently bootaux only supports to boot M33 core from TCM. Since ATF
has changed to use x2 parameter for M33 image address, update the
bootaux command to use input address, so we can support boot from
any possilbe address like TCM, DDR, Flexspi NOR.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a static u-boot config for i.MX93 low drive mode support. When
low drive mode is enabled, VDD_SOC is set to 0.75V. Bus clocks,
A55 core clock (900Mhz), DDR clock (1866MTS), and some peripherals
clocks (USDHC/FLEXSPI/PDM/DISP_PIX/CAM_PIX) must decrease to meet
max frequencies in low drive mode.
Also set standby voltage for buck1
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to datasheet, iMX93 has fused parts with CORE1 or NPU or
both disabled. So update code to support it, the kernel device tree
runtime update will be added in future patches.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Config the A55 alt root clock to 500MHz(LD mode frequency)
by default. Normally, this clock root is only used as an
intermediate clock soure for A55 core/dsu when change the
ARM PLL frequency.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The HW_CTRL_SEL should be cleared when configuring PLL to avoid
potential glitch
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Support print reset cause. Since SRSR is not accessible from non-secure
world, so first save it to grp0, then read it in non-secure world.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There will be build error if CONFIG_SYSRESET is enabled, so guard
the reset_cpu with condition check here
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The MAC addresses are hard coded for bring up. Change it to support
reading from fuse.
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
OPTEE memory region is set secure access only in ATF with configuration
to TRDC, and need to remove it from U-Boot, otherwise U-Boot and Kernel
may crash when accessing the memory
Signed-off-by: Peng Fan <peng.fan@nxp.com>
