Select BOARD_LATE_INIT config so that many board works can be done
in late init stage.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Set VID to 800 mV for Rev1 and set VID as per switch settings
for Rev2.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Update the secure boot headers offsets of Kernel and other
firmware images for SD and XSPI boot sources used by
esbc_validate command.
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Setting fdt_high and initrd_high to 0xffffffffffffffff leads to
various difficulty to resolve bugs.
Remove them and use bootm_size instead to safely contain a kernel,
device tree and initrd for relocation.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Setting fdt_high and initrd_high to 0xffffffffffffffff leads to
various difficulty to resolve bugs.
Remove them and use bootm_size instead to safely contain a kernel,
device tree and initrd for relocation.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Program GIC LPI configuration table:
1. Redistributor PROCBASER configuration table (which
is common for all redistributors)
2. Redistributor pending table (PENDBASER), for all the
available redistributors.
Signed-off-by: Manish Tomar <manish.tomar@nxp.com>
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Update "board_fix_fdt" with correct counter value "i".
This will fix the issue while fetching the "reg_names"
resource from fdt after fixup.
Signed-off-by: Vikas Singh <vikas.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch sets CONFIG_SYS_BOOTMAPSZ to the amount of memory available
to safely contain a kernel, device tree and initrd for relocation. The
way to set fdt_high as 0xffffffff to disable device tree relocation is
removed.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add IIC3 node from mainline Linux DT. This will be further updated in
subsequent DT sync, however adding this node for now is sufficient and
minimal change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The fdtdec_get_addr() does not take into account values set in #address-cells
and #size-cells , but assumes them to be 1 for 32bit systems and 2 for 64bit
systems. This is true for most DTs, however there are exceptions. Switch to
fdtdec_get_addr_size_auto_noparent(), which takes the #address/size-cells
values into consideration, otherwise the reset controller node register
offset is incorrectly parsed.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable DM_SPI and DM_SPI_FLASH in U-Boot on V2H Blanche.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Use ofnode_ instead of fdt_ APIs so that the drivers can support live DT.
This patch updates usb_get_dr_mode() and usb_get_maximum_speed() to use
ofnode as parameter instead of fdt offset. And all the drivers who use
these APIs update to use live dt APIs at the same time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use dev_read_addr_ptr() instead of devfdt_get_addr() so that we can support
live DT.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
mmc bootbus and partconf commands are needed in order to be able to
configure booting from separate boot0/boot1 eMMC partitions.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[jagan: rebase on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
EFI was disabled in f95b8a4b5f because of the missing DTB file,
and indeed, the DTB file is required to load recent versions of GRUB
(2.04) correctly.
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
Sub-nodes of /reserved-memory may be disabled. In this case we should not
reserve memory in the memory map.
Reported-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Fixes: fef907b2e4 ("efi_loader: create reservations after
ft_board_setup")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
On 32 bit systems fix
warning: cast to pointer from integer of different size
[-Wint-to-pointer-cast]
Fixes: a415d61eac ("cmd: map addresses to sysmem in efidebug memmap")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
With CONFIG_OF_CONTROL environment variable $fdtcontroladdr is not defined
and test_efi_helloworld_net() fails.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We need to align the cache buffer to ARCH_DMA_MINALIGN in order to avoid
access errors like
CACHE: Misaligned operation at range [be0231e0, be0235e0]
seen on the MCIMX7SABRE.
Fixes: d5aee659f2 ("fs: ext4: cache extent data")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Commit 41e30dcf87 ("cmd: mmc: Make Mode: printout consistent") fixed
the layout of `mmc info` output. Reflect this change in the respective
testcase.
Also fix a typo in the documentation.
Fixes: 41e30dcf87 ("cmd: mmc: Make Mode: printout consistent")
Signed-off-by: Harald Seiler <hws@denx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently this causes failures of the platform when running the EFI
loader tests, so disable it for now.
This reverts commit af827140e5.
Signed-off-by: Tom Rini <trini@konsulko.com>
- stm32mp: update kernel device tree according the part number
- stm32mp: add 800 MHz profile support = stm32mp15xd and stm32mp15xf
- stm32mp: set cp15 frequency in psci cpu on
- stm32mp: DT alignment with Linux 5.6-rc1
- stm32mp: clk: add SPI5 support and correct CKSELR masks
- stm32mp: ram: fixes on LPDDR2/LPDDR3 support and on tuning
- stm32: i2c: allows for any bus frequency
- sti: timer: livetree and clk API conversion
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl56C0cACgkQ4rK92eCq
k3VlEwgAgOnfIG1WLj+WSUUHmPrglfw0WfoP2Uh7ReZEzaUfuyRfw4/65rtKJri+
4WhT+Az+GO8oblL7557U0QCFYHCw97WpTHu/uQ0CZzr72JWRnArlWwwgQq2vFok5
CBfJ/BDCK72RYUcvNHPOh1wRpS+JIRO8d6HdwbiahBHfxP4J+yWII63VpE4K1Zd7
IDXK3H20jVCTG7jdrHNCaScHWme1qsh8HH132oGRlnf6sxtApxJO7dbV0etY15XF
U1mipAxMoJMIF7utc9GoNia2Tvyi+ZYDjiKCljKwdMW+ebvTulUcikOcXO/aufGo
3nsyv7W6iMfxcK/4aFkQUOCLADY96Q==
=OXic
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200324' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm into next
- stm32mp: fix command stboard
- stm32mp: update kernel device tree according the part number
- stm32mp: add 800 MHz profile support = stm32mp15xd and stm32mp15xf
- stm32mp: set cp15 frequency in psci cpu on
- stm32mp: DT alignment with Linux 5.6-rc1
- stm32mp: clk: add SPI5 support and correct CKSELR masks
- stm32mp: ram: fixes on LPDDR2/LPDDR3 support and on tuning
- stm32: i2c: allows for any bus frequency
- sti: timer: livetree and clk API conversion
Depending on the SoC, a header of four characters is prepended to the
image. There is already a macro defining the number of characters:
RK_SPL_HDR_SIZE, so use it instead of hardcoding "4".
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Since commit 79030a4861 ("rockchip: Add Single boot image
(with binman, pad_cat)") the following boot regression is seen:
U-Boot 2020.04-rc3-00050-gd16e18ca6c-dirty (Mar 09 2020 - 11:40:07 -0300)
Model: Elgin RV1108 R1 board
DRAM: 128 MiB
initcall sequence 67fd12a0 failed at call 6000b927 (err=-22)
This happens because the above commit missed to include the
"rockchip-u-boot.dtsi" for rv1108, so include this file
like it done for other Rockchip SoC dtsi's.
Fixes: 79030a4861 ("rockchip: Add Single boot image (with binman, pad_cat)")
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently the following error message is seen during boot:
U-Boot 2020.01-08751-g55759ae141 (Mar 09 2020 - 14:44:52 -0300)
Model: Elgin RV1108 R1 board
DRAM: 128 MiB
APLL: 600000000 DPLL:1200000000 GPLL:1188000000
ACLK_BUS: 148500000 ACLK_PERI:148500000 HCLK_PERI:148500000 PCLK_PERI:74250000
MMC: dwmmc@30110000: 0
Loading Environment from MMC... OK
In: serial@10210000
Out: serial@10210000
Err: serial@10210000
Model: Elgin RV1108 R1 board
rockchip_dnl_key_pressed: adc_channel_single_shot fail!
....
Since the elgin-rv1108 does not use ADC to read the download
key status, select CONFIG_ROCKCHIP_BOOT_MODE_REG=0 to avoid
such error.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Since commit 8e9a8d0d0c ("rockchip: elgin-rv1108: use board_early_init_f
for per-boar init") the function that configure the board GPIOs is no
longer called since CONFIG_BOARD_EARLY_INIT_F=y is not selected.
These GPIOs do not need to be configured in such early stagem, so change it
to rk_board_late_init() and also select CONFIG_BOARD_LATE_INIT=y
to fix the regression.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to make the console pins more robust to noise, activate
the pullups and increase its drive strength.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
These boards aren't ChromeOS devices so won't have a cros-ec-keyb
input as it's the keyboard available via the ChromeOS Embedded
Controller. Update them to use a USB keyboard which would actually
be available. Also enable the usb keyboard option for those devices
that don't have it enabled already.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use syscon API to get grf base instead of get from dts.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use syscon API to get grf base instead of get from dts.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Retrieve clock rate through device tree. This mimics the behavior of
arm_global_timer in Linux.
Signed-off-by: Nicolas Heemeryck <nicolas.heemeryck@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Update STI timer to support a live tree
Signed-off-by: Nicolas Heemeryck <nicolas.heemeryck@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Do not limit to 3 (100KHz, 400KHz, 1MHz) bus frequencies, but
instead allow for any frequency. Depending on the requested
frequency (via the clock-frequency DT entry), use the spec
data from either Standard, Fast or Fast Plus mode.
In order to do so, the driver do not use anymore spec identifier
by directly handle the requested frequency and from it retrieve
the corresponding spec data to be used for the computation
of the timing register.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
This parameter "st,phy-cal" becomes optional and when it is
absent the built-in PHY calibration is done.
It is the case in the helper dtsi file "stm32mp15-ddr.dtsi"
except if DDR_PHY_CAL_SKIP is defined.
This patch also impact the ddr interactive mode
- the registers of the param 'phy.cal' are initialized to 0 when
"st,phy-cal" is not present in device tree (default behavior when
DDR_PHY_CAL_SKIP is not activated)
- the info 'cal' field can be use to change the calibration behavior
- cal=1 => use param phy.cal to initialize the PHY, built-in training
is skipped
- cal=0 => param phy.cal is absent, built-in training is used (default)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Reduce the delay after BIST delay, from 1ms to 10us
which is enough accoriding datasheet.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
DDRCTRL_PWRCTL.SELFREF_EN needs to be reset before DQS training step, not
to enter in self refresh mode during the execution of this phase.
Depending on settings, it can be set after the DQS training.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Update the BIST config to compute the real use mask for the real
bank, row and col of the used DDR. The values are get from addrmap
register value.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
The derating (timing parameter derating using MR4 read value)
can't be activated during BIST test, as the MR4 read answer will
be not understood by BIST (BISTGSR.BDONE bit stay at 0,
BISTWCSR.DXWCNT = 0x206 instead of BISTWCR.BWCNT = 0x200).
This patch only impacts the tuning on LPDDR2/LPDDR3,
if derateen.derate_enable = 1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Avoid to block the tuning procedure on BIST error (not finished
BIST procedure) by adding a 1000us timeout on the polling of
BISTGSR.BDDONE executed to detect the end of BIST.
The normal duration of the BIST test is around 5us.
This patch also cleanup comments.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Remove one "DDR>" display on command
- next
- step
- go
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
