NXP/Freescale uses macro CONFIG_ARMV8_PSCI to enable their private PSCI
implementation in PPA firmware, but this macro naming too generic, so this
patch replaces it with a specic one CONFIG_FSL_PPA_ARMV8_PSCI.
And this macro CONFIG_ARMV8_PSCI will be used for a generic PSCI for ARMv8
which will be added in following patchs.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures. Migrate all config files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default
in certain architectures. Migrate all config files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
In some cases we were missing CONFIG_USB=y so enable that when needed.
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The PPA binary may be stored on QSPI flash instead of NOR.
So, deprecated CONFIG_SYS_LS_PPA_FW_IN_NOR in favour of
CONFIG_SYS_LS_PPA_FW_IN_XIP to prevent fragmentation of code
by addition of a new QSPI specific flag.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The PPA use PSCI to make secondary cores bootup. So when PPA was
enabled, add the CONFIG_ARMV8_PSCI to identify the SMP boot-method
between PSCI and spin-table.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Create an entry for "config USB_XHCI_DWC3" in Kconfig and
switch over to it for all boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move CONFIG_USB_XHCI to defconfig files for all boards, renaming it
into CONFIG_USB_XHCI_HCD.
As commented in the help of "config USB_XHCI" entry, this has been
a TODO for a long time; now CONFIG_USB_XHCI_HCD and CONFIG_USB_XHCI
have been unified in favor of the former.
Note:
Some boards define CONFIG_USB_XHCI in their headers without
CONFIG_USB, which does not meet the "depends on" in Kconfig.
I added CONFIG_USB=y for those boards when converting.
Otherwise, they would fail to build.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
To use AQR105 PHY's interrupt, we need to invert the IRQ pin polarity
by setting relative bit in SCFG_INTPCR register, because AQR105
interrupt is low active but GIC accepts high active.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.
Signed-off-by: Tom Rini <trini@konsulko.com>
The file fsl_secure_boot.h must be included in config file for
Secure Boot. This is not required to be protected by any macro.
CONFIG_FSL_CAAM must be defined and CONFIG_CMD_HASH should be
turned on.
The above was missing in some config files and all files have been
made uniform in this respect.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1043ARDB Secure Boot Target from NOR has been added.
- Configs defined to enable esbc_validate.
- ESBC Address in header is made 64 bit.
- SMMU is re-configured in Bypass mode.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch also expose the complete DDR region(s) to Linux.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for the third USB controller for LS1043A.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Use the U-Boot Driver Model. Just enable Freescale DSPI driver
and set DSPI related parameters in dts file.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1043ARDB Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 SDRAM (32bit bus)
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* XFI 10G port
* QSGMII with 4x 1G ports
* Two RGMII ports
PCIe:
* PCIe2 (Lanes C) to mini-PCIe slot
* PCIe3 (Lanes D) to PCIe slot
USB 3.0: two super speed USB 3.0 type A ports
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
