Fully resetting the controller is a too big hammer, and the musb_core will
then afterwards fail to communicate with any endpoints other then 0 as
too much state was cleared.
Instead report vbus low for 200ms which will effectively end the current
session without needing to do a full reset.
This fixes usb mass-storage devices no longer working after a "usb reset"
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The AHCI driver currently waits 5s before timing out when sending a
data command to a drive. Some drives take upwards of 8s to respond to
the initial data command while they're spinning up. Increase the
data io timeout to 10s so that those drives can be found on initial
scsi scan.
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com>
Signed-off-by: Andre Przywara <osp@andrep.de>
Enable full 48-bit LBA48 data reads by passing the upper word of the
LBA block pointer in bytes 9 and 10 of the FIS.
This allows uboot to load data from any arbitrary sector on a drive
with 2 or more TB of available data connected to an AHCI controller.
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com>
Signed-off-by: Andre Przywara <osp@andrep.de>
[trini: Make use of CONFIG_SYS_64BIT_LBA in a few places to drop
warnings on platforms that don't enable that feature ]
Signed-off-by: Tom Rini <trini@konsulko.com>
Allow SPL to be built with this option so that we can support device tree
control. Disable the simple bus for now in SPL. It may be needed later.
Signed-off-by: Simon Glass <sjg@chromium.org>
This feature should be deprecated for new boards, and significantly adds
to SPL code size. Drop it. Instead, we can use stdout-path in the /chosen
node.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option is used by some boards, so support it with driver model. This
is really ugly - we should rewrite this driver once all users are moved to
driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
We try to avoid typedefs and these ones are easy enough to remove. Before
changing this header in the next patch, remove the typedefs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add the legacy i2c_reg_read/write() functions to the compatibility layer
so that they can be used when CONFIG_DM_I2C_COMPAT is defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Use the oscillator as the source clock when we cannot achieve a low-enough
speed with the peripheral clock. This happens when we request 3MHz on a SPI
clock, for example.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
At present the driver does not properly honour the requested SPI CS
deactivation delay since the SPI bus is changed in the claim_bus() method.
Everything the claim_bus() method does can be done when the device is probed
(setting the speed and mode) and at the start of a new transfer (where the
fifo_status is already cleared). So drop this method.
Also, until the delay is complete, we should not touch the bus, so make sure
that spi_cs_activate() is called before other things are done in the xfer()
method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This change decreases the interval of calls to:
- display busy indicator
- check ctrlc()
- check cable connection
By this change, breaking the UMS command is more easy on Odroid XU3.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
New files, namely samsung_usb_phy.c and samsung-usb-phy-uboot.h have
been added to u-boot to provide proper PHY handling at Exynos5 SoCs.
This code is used thereafter in the board_usb_init() call.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Add a weak function board_ehci_hcd_init which can be used by the board
file for board specific initialisation.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Like SPI and I2C few GPIO controllers also have
multiple chip instances. This patch adds the
flag 'DM_UC_FLAG_SEQ_ALIAS' in gpio_uclass driver
to control device sequence numbering. By defalut
the dev->r_seq for gpio_uclass will alwalys
returns -1, which leads the gpio driver probe
failure when using the driver with device trees.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Return if USB_MAX_CONTROLLER_COUNT hence the index of the controller
to be initialised is incorrect
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Add "allwinner,sun8i-a33-pinctrl", this is used by the latest upstream
linux sunxi dts files.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Commit 9cc36a2 'dm: core: Add a flag to control sequence numbering' changed
the default uclass behaviour to not support bus numbering. This is incorrect
for PCI and that commit should have enabled the flag for PCI.
Enable it so that PCI buses can be found and the 'pci' command works again.
Also add a test for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Every pin can be configured now from the device tree. A dt-bindings
has been added to describe the different property available.
Change-Id: I1668886062655f83700d0e7bbbe3ad09b19ee975
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Simon Glass <sjg@chromium.org>
The legacy IDE device has a BAR4 (Bus Master Interface BAR) which
needs to be configured.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Remove the '#undef DEBUG' in pci_auto.c so that we can enable debug
message output via '-DDEBUG'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
CONFIG_FRAMEBUFFER_SET_VESA_MODE and CONFIG_FRAMEBUFFER_VESA_MODE
are not x86-specific, so move them to drivers/video/Kconfig and
make them depend on VIDEO_VESA driver. Some cosmetic fixes are
applied to the Kconfig help text as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is no reason to prevent CONFIG_VIDEO_VESA driver working on
non-x86 boards, so remove such limitation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
pci_hose_phys_to_bus() is needed by several drivers. Move it to
pci_common.c to avoid a broken build when CONFIG_DM_PCI is on.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The business for UniPhier Soc family has been transferred from
Panasonic Corporation to Socionext Inc.
Update the SoC select menu in Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In the Linux coding style, it is recommended to include <linux/io.h>
rather than <asm/io.h>. Follow this trend.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This commit adds support to the sunxi SPL to load u-boot from the internal
NAND. Note this only adds support to access the boot partitions to load
u-boot, full NAND support to load the kernel, etc. from the nand data
partition will come later.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This has been tested to the extent that I can enumerate
a asix usb networking adapter and boot a kernel over usb
on the 96boards hikey u-boot port I'm currently doing.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Update the ci_udc driver to support bulk transfer
and also added capability of having multiple dtds
if requested data is more than 16K.
These changes are tested for both the DFU and lthor.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Since i've been married, i also have a new surname.
Mr. Petermaier moved to Mr. Schmelzer.
In this patch i update all files in which my (old) name is present.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Function 'sprintf' does not check buffer boundaries but outputs
to the buffer of fixed size which could potentially cause buffer
overflow. Use a safer function to replace it.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
If we are displaying detected PCI devices (CONFIG_PCI_SCAN_SHOW) display
a 'PCI:' header prior to scan.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Due to a misunderstanding, in 698a12b we reverted changes that we in
fact wanted to keep. So lets fix that mistake and bring the code back
to how it should have been.
This reverts commit 698a12bef9.
Signed-off-by: Tom Rini <trini@konsulko.com>
The CPU temperature grade from OTP is now used to define the critical
threshold at which point we busyloop until we are below, however this
threshold is still too low.
Instead of 20C below the max CPU temperature, change it to 5C defined now
by TEMPERATURE_HOT_DETLA for clarity. Rename 'passive' to 'critical'
as that better defines our use case here. Additionally change the output
of the busyloop message to show the max CPU temperature as well as current.
Before:
CPU Temperature is 101 C, too hot to boot, waiting...
CPU Temperature is 101 C, too hot to boot, waiting...
After:
CPU Temperature (101C) too close to max (105C) waiting...
CPU Temperature (101C) too close to max (105C) waiting...
Cc: Stefan Roese <sr@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Cc: Jason Liu <r64343@freescale.com>
Cc: Ye Li <b37916@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Peng Fan <b51431@freescale.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
