Add the initial support for Elgin R1 board, which is based on the
RV1108 SoC and has the following features currently supported in
U-Boot:
- UART
- eMMC
- USB
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This is a sync with kernel mainline dts.
The U-Boot eMMC does not need to care about the power for Rockchip
SoCs, because if the board is using eMMC, the power will default on
(for bootrom), so the 'vmmc', 'vqmmc' is only useful for SD in U-Boot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
vcc5v0_host and usbhub_enable share gpio4 RK_PA3,
which is a problem during probing (the second probe
will trigger a -EBUSY, when trying to get the gpio handle).
An analysis of the situation shows, that both regulators
are actually describing the same supply.
This patch removes the (currenlty not successful probing)
regulator vcc5v0_host from the DTS and adds the pinctrl-*
setting to usbhub_enable.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Phiilipp Tomsich <philipp.tomsich@theobroma-systems.com>
At present the 'beep' sound generates a waveform for only one channel even
if two are being used. This means that the beep is twice the frequency it
should be. Correct this by making it a parameter.
The fix in a previous commit was correct for sandbox but not for other
boards.
Fixes: 03f11e87a8 ("sound: Correct data output in sound_create_square_wave()")
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these parameters are hard-coded in the sdl interface code.
Allow them to be specified by the driver instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update sandbox's device tree and config to use driver model for sound. Use
the double buffer for sound output so that we don't need to wait for the
sound to complete before returning.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update snow's device tree and config to use driver model for sound. Also
update the others as best we can.
Spring does not appear to have audio support in the kernel. The smdk5250
and smdk5420 boards use a wolfson codec which I cannot test with. So the
only boards that is tested and known to work are snow, pit and pi.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow setting the i2s pinmux correctly on exyno5420 so that i2c can be
used on that SoC. Also rename EXYNOS_AUDSS to something consistent with
other naming.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current ID enums start from 1 but there does not seem to be any reason
that they cannot start with 0. Adjust the code to avoid the +1 in
codec_init().
Signed-off-by: Simon Glass <sjg@chromium.org>
The current dev_read...() functions use s32 and u32 which are convenient
for device tree but not so useful for normal code, which often wants to
use normal integers for values.
Add a helper which supports returning an unsigned int. Also add signed
versions of the unsigned readers.
Signed-off-by: Simon Glass <sjg@chromium.org>
The sound driver pulls together the audio codec and i2s drivers in order
to actually make sounds. It supports setup() and play() methods. The
sound_find_codec_i2s() function allows locating the linked codec and i2s
devices. They can be referred to from uclass-private data.
Add a uclass and a test for sound.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use a single buffer for sound which means we cannot be
playing one sound while queueing up the next. This wouldn't matter except
that a long sound (more than a second) has to be created as a single
buffer, thus using a lot of memory. To better mimic what real sound
drivers do, add support for double buffering in sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
The i2s bus is commonly used with audio codecs. It provides a way to
stream digital data sychronously in both directions. U-Boot only supports
audio output, so this uclass is very simple, with a single tx_data()
method.
Add a uclass and a test for i2s.
Signed-off-by: Simon Glass <sjg@chromium.org>
An audio codec provides a way to convert digital data to sound and vice
versa. Add a simple uclass which just supports setting the parameters for
the codec.
Signed-off-by: Simon Glass <sjg@chromium.org>
This structure contains information that is likely needed by any i2s
driver so it seems useful to attach it to the (forthcoming) i2c uclass.
For now, just rename it.
Signed-off-by: Simon Glass <sjg@chromium.org>
The U-Boot sound system provides basic support for beeping. At present it
does not use driver model, but it needs to be converted. Add an option to
enable driver model for sound. For now it is not connected to anything.
Future work will add drivers which use this option. It will then be
removed once everything is converted.
Signed-off-by: Simon Glass <sjg@chromium.org>
For snow the codec is at address 0x11 on the i2c bus, in 7-bit format.
The device tree and code are in 8-bit format (i.e. shifted left one bit).
Fix both. Fix pit in a similar way.
Signed-off-by: Simon Glass <sjg@chromium.org>
These are only used in two functions so can be made local.
Also change the first argument of max98095_do_init() to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model we want to do a minimal probe when the device is probed
and then set up the codec interface later when a sound is actully played.
Split this setup code out into its own function to help with this.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model we want to do a minimal probe when the device is probed
and then set up the codec interface later when a sound is actully played.
Split this setup code out into its own function to help with this.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model we cannot pass in the global struct, but instead want
to pass in the driver-private data. Split some of the code out of
wm8994_init() to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the driver-private data is global. To allow this code to be
used with driver model, change it to pass the data down to each function.
Use the name 'priv' consistently throughout.
Also rename max98095_update_bits() to max98095_bic_or() which is more
descriptive and shorter, thus breaking fewer lines with the parameter
addition.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the driver-private data is global. To allow this code to be
used with driver model, change it to pass the data down to each function.
Use the name 'priv' consistently throughout.
Also rename wm8994_update_bits() to wm8994_bic_or() which is more
descriptive and shorter, thus breaking fewer lines with the parameter
addition.
Signed-off-by: Simon Glass <sjg@chromium.org>
This struct is only used by the Samsung I2C driver and should move into
that driver. For now, rename it so it is clear that is driver-private
info.
Signed-off-by: Simon Glass <sjg@chromium.org>
The serial driver in the kernel moved from ttyOx to ttySx a while
ago. This patch updates the console parameter to align with the
kernel change.
Signed-off-by: Adam Ford <aford173@gmail.com>
The uts created in do_ut_overlay() is not the one used in
cmd_ut_category(). Currently all tests are therefore called with
uts->priv = NULL and fail.
Using a static variable is the easiest fix here.
Fixes: e93232e15e ("test: overlay: Use cmd_ut_category()")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
