Improve the README by adding instructions on how to boot using
Falcon mode, which allows the SPL to load the kernel directly,
without using U-Boot proper.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
When CONFIG_SPL_OS_BOOT is selected, it is still convenient to be able
to escape from Falcon mode and boot to U-Boot proper.
Add a mechanism that allows booting in U-Boot proper when the
key 'c' is entered on console at boot time.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Sync the Falcon mode instructions with the ones fro pico-imx7d.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Add support for the VXT VL050-8048NT-C01 panel connected through
the 24 bit parallel LCDIF interface.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Because FIT could not be used for AHAB secure boot on i.MX8,
so switch to use container image that could let SPL verify
ATF and U-Boot with AHAB.
Enable HUSH_PARSER in defconfig to make run netboot could work.
Note: The AHAB related code has not been added.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Because FIT could not be used for AHAB secure boot on i.MX8,
so switch to use container image that could let SPL verify
ATF and U-Boot with AHAB.
Note: The AHAB related code has not been added.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The first stage of flash.bin is larger than 584 * 512, so when
writting u-boot.itb, some data will be override. Enlarge the
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to fix boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since the SD3.0 kernel driver needs M4 image support, this causes
problem for usb boot booting into kernel. To decouple the relationship,
we modify the FDT file in u-boot to disable SD3.0.
So the kernel won't depend on M4 image.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This prevents messages like
gpio@20a0000: get_value: error: gpio GPIO2_2 not reserved
when CONFIG_DM_GPIO is enabled.
Also, when CONFIG_DM_GPIO is enabled, checkboard is too
early to use gpio_get_value, so read it directly on failure.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Commit e37ac717d7 ("Convert to use fsl_esdhc_imx for i.MX platforms")
converted FSL_ESDHC to FSL_ESDHC_IMX, but the config check for
apalis_imx6 wasn't updated accordantly.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Only one dtb is currently supported, so match with imx6-apalis.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
To support DM_VIDEO,
Add display node for lcdif
Drop board iomuxc settings.
Enable DM_VIDEO
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
When booting SPL on the board, met boot failure:
"
Trying to boot from MMC2
MMC Device 1 not found
spl: could not find mmc device 1. error: -19
SPL: failed to boot from all boot devices
"
Let's register the two mmc controllers in SPL stage to
avoid boot failure.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add i.MX6ULZ board support. the i.MX6ULZ is SW compatible
with i.MX6ULL. so most code of i.MX6ULL can be reused
by i.MX6ULZ.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Modify the configuration naming to be generic to xilinx rather than
specific to Versal. The offset value is different for Zynq and ZynqMP
to avoid overlapping with FSBL.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move the exisiting function of getting board dtb from versal to a common
Xilinx folder.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Probe ZynqMP firmware driver on the board initialization phase and
ensure that firmware is in place to continue execution. The probing is
done on board_init so it can be used for both SPL and U-Boot proper.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use the new function from firmware version to get the firmware version.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
New firmware header to place firmware specific macro and function
declarations. The patch also moves the macros defining PM operations as
well as some helper macros.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There were several changes in past in this file without removing headers
(watchdog cleanup, soft reset, etc). That's why remove additional useless
headers.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Setup initrd_high and fdt_high to be placed in lowmem space for kernel to
be able to reach it. Values are setup at run time to ensure that the same
setting can be used on different memory setup. Do this setting only when
variables are not
Similar run time detection was done for Zynqmp and Versal.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Similar SCs but different wiring.
- dc_i2c is connected to X-PRC cards that's why label is required to have
an option to hook up some devices.
- Exactly identify i2c devices on x-prc boards.
In case of missing i2c connection devices won't be accessible.
- USB 0 should be device mode with super speed.
- USB 1 should be host mode.
- Fix i2c mux reset pin entry - commented, not verified.
- Fix i2c1 eeprom compatible string - it is an ST 128Kbit device.
Need to use atmel fallback.
- Fix si570 I2C slave address and add corresponding part numbers.
- Enable AMS for system monitoring.
- phy reset property should be commented because it will throw a
warning dump when called from context that can sleep.
No support for phys property (zynqmp phy driver) with SGMII.
Add is-internal-pcspma property required by uboot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Xilinx Zynq SoC has two sdhci controllers but boot is only possible from
the first one. That's why there is a need to specify controller number.
mmc1 is supposed to be secondary boot device and should be also listed in
distribution boot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add zu48dr and zu49dr to the list of zynqmp devices. The zu48dr and zu49dr
are the new RFSoC silicons with id values of 0x7b and 0x7e.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new jtag distro boot command to look for bootscript file in
DDR and execute it first incase of jtag bootmode.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new dfu usb distro boot command to look for bootscript
from dfu-util and runs it.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
This patch adds new jtag distro boot command to look for bootscript file
in DDR and execute it first incase of jtag bootmode.
This patch also updates scriptaddr to 512MB as there is high of script
corruption incase of bigger kernel image.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Code reads DT and setup MMU table based on memory node. This will ensure
that only DT needs to be changed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is setting up the initrd_high to as high as possible by leaving
max stack size for u-boot so that bigger rootfs can also be loaded by
u-boot for booting kernel.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is setting up the initrd_high to as high as possible by leaving
max stack size for u-boot so that bigger rootfs can also be loaded by
u-boot for booting kernel.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds PL bitstream load support for Versal platform. The PL
bitstream is loaded by making an SMC to ATF which in turn communicates
with platform firmware which configures and loads PL bitstream on to PL.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define board_late_init which performs bootmode detection
and prepares corresponding distro boot commaand sequence.
Also disable it for mini platforms because simply there is no need to have
it enabled.
But also disable it for virtual platform because Qemu is not modelling this
register space that's why travis testing would fail. This configuration
should be reverted when mainline Qemu is updated.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds sdboot command script for reference.
This can be converetd into uboot script using mkimage and
use for booting.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Thsi patch adds qspiboot command script for reference.
This can be converetd into uboot script using mkimage and
use for booting.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Boot from QSPI nor flash.
The at91bootstrap, u-boot, u-boot env redundant, u-boot env,
device tree and kernel will reside in the QSPI nor flash.
The rootfs will reside in the NAND flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
- EBI Chip Select Register is now in SFR,
- the pins are set to default values,
- timings are matching MT29F4G08BABWP's nand flash requirements.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Special Function Registers (SFR) are present in sam9x5 and
sam9x60 too, rename sama5_sfr to at91_sfr.h.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add new board SAM9X60-EK using the ARM926 SAM9X60 SoC.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
[tudor.ambarus@microchip.com:
- fix number of DRAM banks:
One DDR2-SDRAM (W972GG6KB 2 Gbit = 16 Mbit x 16 x 8 banks]
- drop SPL related macros
- drop memtest macros
- drop CONFIG_SPI_BOOT, CONFIG_SYS_USE_DATAFLASH related macros
- drop inclusion of asm/arch/at91sam9_smc.h]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Remove 2017 from being printed at boot video console.
This is outdated.
To avoid this situation, remove the year completely.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add support for qspi memory on board. Created boot support for QSPI
for both u-boot proper and SPL.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
