Commit graph

12769 commits

Author SHA1 Message Date
Patrick Delaunay
d573e46168 stm32mp1: board: enable v1v2_hdmi and v3v3_hdmi regulator on dk2 boot
As for Audio codec IC, HDMI IC is not "IO safe".
HDMI regulators (v3v3 and v1v2) must be enabled to allow
I2C1 bus usage. HDMI IC must be under reset during power up
and keep HDMI and AUDIO devices in reset while they are not
used in U-Boot to keep them in low power mode
(each device can be kept in reset independently keeping their
power supplies ON until kernel).

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 11:19:23 +02:00
Patrick Delaunay
8b8b3d6b55 stm32mp1: board: add environment variable for board id and board rev
Add variable to identify board with HW id (read from OTP)
and revision.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 11:19:23 +02:00
Patrick Delaunay
178a415534 stpmic1: program pmic to keep only the debug unit on
Depending on backup register value, we maintain the debug unit
powered-on for debugging purpose.
Only BUCK1 is required for powering the debug unit, so revert
the setting for all the other power lanes, except BUCK3 that
has to be always on.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 09:36:56 +02:00
Tom Rini
12277acda0 Merge branch '2019-08-26-master-imports'
- Assorted minor bugfixes
2019-08-26 17:45:20 -04:00
Hou Zhiqiang
c36643ff48 powerpc: Enable device tree support for P2041RDB
Add device tree for P1041RDB board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-26 21:25:23 +05:30
Hou Zhiqiang
caa756975c powerpc: Enable device tree support for P2020RDB
Add device tree for P1020RDB boards and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-26 21:23:22 +05:30
Hou Zhiqiang
ec70cedbce powerpc: Enable device tree support for P1020RDB
Add device tree for P1020RDB boards and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-26 21:23:21 +05:30
Hou Zhiqiang
fa3602859f powerpc: Enable device tree support for T1042D4RDB
Add device tree for T1042D4RDB board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-26 21:23:20 +05:30
Hou Zhiqiang
bd74ea1908 powerpc: Enable device tree support for T1024RDB
Add device tree for T1024RDB board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-26 21:21:02 +05:30
Hou Zhiqiang
bf4e0ff321 powerpc: Enable device tree support for T2080RDB
Add device tree for T2080RDB board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-26 21:16:32 +05:30
Samuel Egli
055c2a78b7 MAINTAINERS,board/siemens: update maintainer
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
2019-08-26 11:46:29 -04:00
Bin Meng
44016bc598 riscv: qemu: Fix kconfig build warning
When 'make qemu-riscv64_defconfig', there is a build warning:

  board/emulation/qemu-riscv/Kconfig:24:
  warning: config symbol defined without type

Fix it by specifying the config symbol type to 'hex'.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
2019-08-26 16:09:02 +08:00
Lukas Auer
e456a81935 riscv: qemu: add SPL configuration
Add two new configurations (qemu-riscv{32,64}_spl_defconfig) with SPL
enabled for RISC-V QEMU. QEMU does not require SPL to run U-Boot. The
configurations are meant to help the development of SPL on RISC-V.

The configurations enable RAM as the only SPL boot device. Images must
be loaded at address 0x80200000. In the default boot flow, U-Boot SPL
starts in machine mode, loads the OpenSBI FW_DYNAMIC firmware and U-Boot
proper from the supplied FIT image, and starts OpenSBI. U-Boot proper is
then started in supervisor mode by OpenSBI.

Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
2019-08-26 16:07:42 +08:00
Rohan Garg
fa177ff020 board: puma: Use rockchip_* helpers to setup cpuid and macaddr
We should use the shared helpers to setup the necessary parts

Signed-off-by: Rohan Garg <rohan.garg@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23 18:15:31 +08:00
Kever Yang
cb8c492f20 rockchip: rk3288: remove fennec board support
Since there is no one using this board, remove it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23 15:27:40 +08:00
Laurentiu Tudor
b249fcba00 armv8: ls1028a: add icid setup for platform devices
Add ICID setup for the platform devices contained on this chip: usb,
sata, sdhc, edma, qdma, gpu, display and sec.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Laurentiu Tudor
5c6dc6c9a9 armv8: ls1088a: add icid setup for platform devices
Add ICID setup for the platform devices contained on this chip: usb,
sata, sdhc, sec. The ICID macros for SEC needed to be adapted because
the format of the registers is different.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Chuanhua Han
1748990ab2 armv8: ls1088aqds: support DSPI mode by hwconfig
BRDCFG4[USBOSC] and BRDCFG5[SPR] register field of Qixis device is used
to control SPI and other IP signal routing.

USBOSC:
0= SPI_CLK used as external USB REFCLK input driven with 24.000 MHz.
SPI devices are unusable in this mode.
1= SPI_CLK used as SPI clock.
SPI devices are usable in this mode. USB block is clocked from
internal sources

SPR[3:2]:
SPI_CS / SDHC_DAT4:7 Routing (schematic net CFG_SPI_ROUTE[3:2]):
00= SDHC/eMMC 8-bit
01= SD Card Rev 2.0/3.0
10= SPI on-board memory
11= TDM Riser / SPI off-board connector.
The default value is 00 if an SDCard/eMMC card is selected as the boot
device.

SPR[1:0]:
SPI_SIN/SOUT/SCK Routing (schematic net CFG_SPI_ROUTE[1:0]):
00= SDHC Sync loop
01= TDM Riser / SPI off-board connector.
10= SPI on-board memory.
11= SPI off-board connector.

By default, the SPI feature is not available, so we need to configure
the above register fields to select the route to the SPI feature.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Pankaj Bansal
2e35d07658 boards: fsl: lx2160ardb: enable flexcan
Flexcan in LX2160ARDB is controlled by FPGA register boardcfg4
bit 5. enable this bit so that flexcan is enabled in LX2160ARDB.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Chuanhua Han
c8b2e364b6 armv8: ls1088aqds: Add support of I2C driver model.
Udate ls1088aqds board init code to support DM_I2C.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Chuanhua Han
5dd043a082 boards: ls1088a: Add support of I2C driver model
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM
I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch
solves the problem that the i2c-related api of the ls1088a platform
does not support dm.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Chuanhua Han
885ae0513a boards: ls2088aqds: Add support of I2C driver model.
Update ls2088aqds board init code to support DM_I2C.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Chuanhua Han
db07c447ca rtc: ds3232/ds3231: Add support to generate 32KHz output for driver module
Add an implementation of the rtc_enable_32khz_output() that uses the
driver model i2c APIs.

Also put code related to rtc_enable_32khz_output
under CONFIG_RTC_ENABLE_32KHZ_OUTPUT.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Chuanhua Han
654e4e70d4 boards: ls2088a: Add support of I2C driver model.
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM
I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch
solves the problem that the i2c-related api of the ls2088a platform
does not support dm.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:35 +05:30
Chuanhua Han
954cd78828 boards: ls1028a: Add support of I2C driver model
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM
I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch
solves the problem that the i2c-related api of the ls1028a platform
does not support dm.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:35 +05:30
Chuanhua Han
0eba65d201 boards: lx2160a: Add support of I2C driver model
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C
API when DM_I2C is used. When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch solves
the problem that the i2c-related api of the lx2160a platform does not
support dm.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:35 +05:30
Yuantian Tang
0f6607f9e9 common: qixis: make the qixis compatible with new soc
This driver needs modification to work with new soc,
like ls1028, since bitmap of RCFG is changed to
RESV[7:5] LIVE[4] WDEN[3] RESV[2:1] GO[0]
   000      1       0        00      0

Also the RCW location is moved to only dutcfg0.
RESV[7:4] RCWSRC[3:0]
   1111   configurable

Following commands are functional now
qixis_reset
qixis_reset sd
qixis_reset qspi
qixis_reset emmc

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:35 +05:30
Meenakshi Aggarwal
cf0bbbd1ee drivers: net: mc: Report extra memory to Linux
MC firmware need to be aligned to 512M, so minimum 512MB DDR is reserved.
But MC support to work with 128MB or 256MB DDR memory also, in this
case, rest of the memory is not usable.
So reporting this extra memory to Linux through dtb memory fixup.

Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:35 +05:30
Adam Ford
e9e2216ef5 davinci: omapl138-lcdk: Remove empty compiler directives
There is an #ifdef with nothing inside it any longer.  This patch
removes this empty #ifdef

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-20 11:46:38 -04:00
Adam Ford
1905af1e4c ARM: davinci: Remove duplicated references
The Kconfig file calls to ti/common/Kconfig twice which makes
several of the menu items repeat themselves.  In an effort to
clean this up, this patch removes the second call which eliminates
the duplicate menu items.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-20 11:46:38 -04:00
Adam Ford
a24b051a14 Revert "ARM: da850-evm: Enable SPI Flash and NAND Flash when booting NOR"
Sorry for the noise, but there appears to be a regression with older
hardware.  Since it broke the direct_nor boot option, it should be
reverted until a better solution is available.

This reverts commit 51cd1e2373.
2019-08-20 11:46:38 -04:00
Yegor Yefremov
debe7a141d arm: baltos: use device tree alias to access Ethernet slave
The full path has changed in the recent kernels so that it is
not possible to load them. Aliases "ethernet0" and "ethernet1"
are still present in both legacy and new kernels.

Also, fix error messages to correspond to the taken actions.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2019-08-20 11:46:11 -04:00
Levin Du
8a681f4c5a rockchip: rk3399: Add ROC-RK3399-PC support
Add initial support for ROC-RK3399-PC board.

Specification
- Rockchip RK3399
- LPDDR4 4GiB
- eMMC slot
- SD card slot
- RTL8211E 1Gbps
- HDMI Out, DP, MIPI DSI/CSI, EDP
- PCIe M.2
- USB 2.0, USB-3.0
- USB C Type

Commit details of rk3399-roc-pc.dts sync from Linux v5.2:
"arm64: dts: rockchip: add support for ROC-RK3399-PC board"
(sha1: 8bb878cf20ae10809c36db96993bfce7026d062b)

Signed-off-by: Levin Du <djw@t-chip.com.cn>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-19 12:43:26 +08:00
Tom Rini
88c7a0a8c2 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvell
- Various improvements to Keymile boards - mostly DT conversation
  (Pascal & Holger)
- Removal of now unsupported Keymile boards (Pascal & Holger)
- Small MVEBU PCI fix (Marek)
- Turris Omnia defconfig update (Marek)
- Misc Allied Telesis defconfig updates (Chris)
2019-08-12 23:03:44 -04:00
Tom Rini
60f38d82c4 - amlogic: add support for the SEI Robotic SEI510
-----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAl1RU+gACgkQd9zb2sjI
 SdE/OBAAgytrPuru4s5bBwIqBpMk2IbmNsuAOG6FY6plXpUyaYRsn+wUZikPkkif
 Wv9f/iB2Zv7wHtKnMbM8dafCViaMmU7m5mF71GS2Xt7dEfZZQWN/RWwKe5UfTVxF
 7hI5RU6OQMN8kwEB/AJIoFzhxzND9I2E5gocAafGn+dakmxoNR54rr//7DGlULNM
 kOYucXV5oYwDxc14nUXkYP13UrKds0bN0iWk+s367uPUcUuzEprD+/LV0NYTqLMp
 udCE0RLEvA8b3TxZeR9skjPWwBFc7crzWRsVDBdKujmTEvsZdEoBo0FbqEn6nr1u
 m5Q2dMYn2TvRHL4t7fppeqAryjE6JPmyuHUE4F+umvIs3QOjijgTPmG3pC0Trb1Z
 +iXrcoBbv+/zCbt5TQpPqYwW9wp3VSHGZlY9NZKS+Lwo/+Kj+JEXjzmzpASO8ruU
 5NCQE1mNZtb/i2UDN649NptoNSxV+jP5qjh9rJZuQMF5oL6e3UMrfz/d7EeWOvSY
 MKRZIGm+HEPXwR7dOleHAuHDHBZ5ztWGlYyNMjtgTvgHk499tvvZYQ00LrHU1Uze
 wKeK3uN5UQujcJf14wM2AhHZhB22ZUy4onshY8rI4lUq1oRpc8nZ+31R+xXmuC/o
 wt+KmyTdD4Eva1batGmM1zpl3bSgDndyBo5FNlWH1xY5jZU/6Ro=
 =M0sg
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-amlogic-20190812' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic

- amlogic: add support for the SEI Robotic SEI510
2019-08-12 23:03:35 -04:00
Tom Rini
9c6115822e Merge branch '2019-08-11-ti-imports'
- More DaVinci updates and fixes
- PCIe support on am65x
- Watchdog converted to DM
- Assorted other bugfixes
2019-08-12 18:47:53 -04:00
Adam Ford
51cd1e2373 ARM: da850-evm: Enable SPI Flash and NAND Flash when booting NOR
Historically there have been various boot options, SPI flash,
NAND or NOR. The NOR flash is mutually exclusive with MMC, but
it isn't mutually exclusive with NAND or SPI Flash, so this patch
enables both NAND flash and SPI Flash when booting from NOR.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-12 13:33:42 -04:00
Hannes Schmelzer
60df809f62 board/BuR/brsmarc1: initial commit
This commit adds support for the B&R brsmarc1 SoM.

The SoM is based on TI's AM335x SoC.
Mainly vxWorks 6.9.4.x is running on the board,
doing some PLC stuff on various carrier boards.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-08-12 13:33:37 -04:00
Anselm Busse
2800bb155b ARM: omap3: overo: Fix MMC init for SPL
The SPL for the Overo board does not initialise the MMC. Hence, it
cannot load the main boot loader from the SD card susequently. This
patch moves the initialisation code for the MMC so it gets included in
the SPL.

[trini: Add missing header]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-12 07:24:29 -04:00
Jerome Brunet
0998367515 boards: meson: add g12a sei510
The SEI510 board is based on the Amlogic S905X2 SoC
from the Amlogic G12A SoC family.

The board has the following specifications :
- Amlogic S905X2 ARM Cortex-A53 quad-core SoC
- XGB DDR4 SDRAM
- 10/100 Ethernet (Internal PHY)
- 1 x USB 3.0 Host
- eMMC
- SDcard
- Infrared receiver
- SDIO WiFi Module

The board default behaviour is for booting Android and triggers
fastboot on recovery or reboot mode.

USB vendor ID (used by fastboot) is 0x18d1 (Google) for
default udev rules for existing android users work out of the box.

Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-08-12 10:04:03 +02:00
Holger Brunck
00f9baf8eb powerpc/km: remove unmaintained board KMLION1
This board is unmaintained and can be removed. This also allows us to
remove kmp204x-common.h and integrate it in kmp204x.h.

Signed-off-by: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-08-12 09:12:38 +02:00
Holger Brunck
7b472733d8 powerpc/km: remove unmaintained target KMVECT1
Signed-off-by: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-08-12 09:12:38 +02:00
Pascal Linder
1bd17b9f7b km/arm: remove unmaintained target PORTL2
Remove the PORTL2 board and all its dependencies as it is no longer
supported by the company.

Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-08-12 09:12:38 +02:00
Pascal Linder
abbaa8ed14 km/rgmii: port Ethernet interface of KM Kirkwood boards to driver model
Activate the driver model for the Ethernet interface (RGMII) in the KM
Kirkwood Kconfig file. Additionally, raise the auto negotiation timeout
to eight seconds as more time is required for those boards.

Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-08-12 09:12:38 +02:00
Pascal Linder
b75e9e3fce km/uart: port UART interface of KM Kirkwood boards to driver model
Activate the driver model for the serial interface in the KM Kirkwood
Kconfig file. The associated preprocessor definitions could be removed
from the header file. However, the clock of 200 MHz needs to be declared
in the device tree.

Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-08-12 09:12:38 +02:00
Pascal Linder
432579c4d1 km: remove obsolete definitions in KM header files
After moving the KM specific configurations to Kconfig, the associated
preprocessor definitions can now be removed in the headers. Moreover, the
whitelist has been adapted correspondingly.

Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-08-12 09:12:38 +02:00
Pascal Linder
707f06f331 km: add Kconfig menus for KM boards
To execute the conversion away from board specific header files, Kconfig
menus have been implemented for all KM boards and additionally for those
having an ARM architecture.

For the moment, the preprocessor definitions stay in the headers. The
boolean types, however, needed a modification (#define CONFIG_* 1).

The default configuration files of some boards required an update in order
to not change the currently defined values of the configurations.

Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-08-12 09:12:38 +02:00
Simon Glass
f3998fdc4d env: Rename environment.h to env_internal.h
This file contains lots of internal details about the environment. Most
code can include env.h instead, calling the functions there as needed.

Rename this file and add a comment at the top to indicate its internal
nature.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fixup apalis-tk1.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-11 19:27:31 -04:00
Simon Glass
e7dcf5645f env: Drop environment.h header file where not needed
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-11 16:43:41 -04:00
Simon Glass
0ac7d722ed env: Move get/set_default_env() to env.h
Move these functions to the new header file and rename set_default_env()
to env_set_default() so that it has a consistent env_ prefix.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-11 16:43:41 -04:00
Simon Glass
7b51b576d6 env: Move env_get() to env.h
Move env_get() over to the new header file.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-11 16:43:41 -04:00
Simon Glass
9fb625ce05 env: Move env_set() to env.h
Move env_set() over to the new header file.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-11 16:43:41 -04:00
Simon Glass
6bf6dbee01 env: Move env_get_yesno() to env.h
Move env_get_yesno() over to the new header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-08-11 16:43:41 -04:00
Simon Glass
9eef56dbe3 env: Move env_get_ulong() to env.h
Move env_get_ulong() over to the new header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-08-11 16:43:41 -04:00
Simon Glass
168068fb3d env: Move env_set_ulong() to env.h
Move env_set_ulong() over to the new header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-08-11 16:43:41 -04:00
Simon Glass
c7694dd483 env: Move env_set_hex() to env.h
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-08-11 16:43:41 -04:00
Simon Glass
4bfd1f5d62 env: Move env_init() to env.h
Move env_init() over to the new header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-08-11 16:43:41 -04:00
Simon Glass
3a7d55716d env: Move env_get_f() to env.h
Move this function over to the new header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-08-11 16:43:41 -04:00
Simon Glass
0c670fc148 common: Move gzip functions into a new gzip header
As part of the effort to remove things from common.h, create a new header
for the gzip functions. Move the function declarations to it and add
missing documentation.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-08-11 16:43:41 -04:00
Manivannan Sadhasivam
c62c7ef779 board: hisilicon: Add support for Hikey960 board
This commit adds board support for Hikey960 board from Hisilicon. This
board is one of the Consumer Edition boards of the 96Boards family
powered by Kirin960 SoC.

More information about this board can be found in 96Boards website:
https://www.96boards.org/product/hikey960/

The initial supported/tested devices include:
 - Debug serial
 - SD

With these support, it's good enough for loading Linux Kernel from SD.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-08-11 16:43:41 -04:00
Anatolij Gustschin
490e6d6859 board: siemens: extend factoryset reading for giedi and deneb boards
giedi and deneb are i.MX8X based and have additional data with
WLAN MAC in factoryset container. Enable building for these
boards and adapt factoryset functions to set WLAN MAC and dtb
name in environment.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-08-11 16:42:03 -04:00
Anatolij Gustschin
4987bc2a1a board: siemens: adapt factoryset reading for DM_I2C enabled boards
For new boards we always enable DM_I2C. Extend factoryset functions
to support EEPROM reading on these boards.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-08-11 16:42:03 -04:00
Tom Rini
feb5a02f86 Merge branch 'master' of git://git.denx.de/u-boot-sh
- R8A77980 V3H support
2019-08-10 17:57:58 -04:00
Tom Rini
9fd8b2c8c7 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86
- Enable SD slot on Intel Edison
- Populate CSRT ACPI table for shared DMA controller on Intel Tangier
- Convert Intel ICH-SPI driver to use new spi-mem ops
- Enable config_distro_bootcmd for QEMU x86
- Support U-Boot as a payload for Intel Slim Bootloader
- Avoid writing temporary asl files into the source tree which fixes the
  parallel build issue occasionally seen
2019-08-09 23:27:15 -04:00
Marek Vasut
3ebb91914f ARM: renesas: Add R8A77980 V3H Condor board code
Add board code for the R8A77980 V3H Condor board.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-08-09 23:15:01 +02:00
Marcel Ziswiler
4c63a601b9 apalis-tk1: support v1.2 hardware revision
Support the V1.2 hardware revision with the following pin muxing
changes:

Ddc_scl_pv4 and ddc_sda_pv5 previously used as Apalis GPIO3 and GPIO4
are now used as DDC pins.

Gen2_i2c_scl_pt5 and gen2_i2c_sda_pt6 previously used as DDC pins are
now used as USB power enable signals.

Usb_vbus_en0_pn4 and usb_vbus_en1_pn5 previously used as USB power
enable signals are now used as GPIO3 and GPIO4.

Additionally a new device tree file tegra124-apalis-v1.2-eval.dtb is
loaded on V1.2 and later modules and resp. USB power enable signals
activated.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2019-08-09 10:01:35 -07:00
Dominik Sliwa
5a20adf446 apalis-tk1: remove non-essential power rails on boot
When mainline kernels reboot TK1 they use SW_RESET,
that reset mode does not reset PMIC. Some rails
need to be off for RAM Re-repair to work correctly.

Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2019-08-09 10:01:35 -07:00
Igor Opaniuk
538ab6c0a1 apalis-tk1: set apalis gpio 8 aka fan_en
Make sure the Apalis GPIO 8 aka FAN_EN is on when using Apalis TK1
modules.

Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2019-08-09 10:01:34 -07:00
Marcel Ziswiler
5b5de78b4a apalis-tk1: do not explicitly release reset_moci#
By keeping RESET_MOCI_CTRL low we avoid explicitly releasing
RESET_MOCI#.

Please note that module hardware versions up to V1.1A will already
release RESET_MOCI# in hardware coming out of reset.

Please further note that with this change the USB hub on the Apalis
Evaluation board is kept in reset in U-Boot and therefore none of its
ports are operational in U-Boot.

Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2019-08-09 10:01:34 -07:00
Park, Aiden
d8f6db4768 board: intel: Add new slimbootloader board
Add slimbootloader board to run U-boot as a Slim Bootloader payload
- Add new board/intel/slimbootloader directory with minimum codes
- Add slimbootloader configuration files
- Add doc/board/intel/slimbootloader.rst

Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add slimbootloader board MAINTAINERS file]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2019-08-09 22:24:02 +08:00
Andy Shevchenko
42ef707922 x86: edison: Enable SD slot
Enable SD slot on Intel Edison platform.

By default firmware doesn't put device on active state. Thus,
we have to do this explicitly.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-08-09 22:24:02 +08:00
Tom Rini
21bc1935b1 Merge tag 'u-boot-rockchip-20190809' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Add rk3399 boards Khadas Edge/-V/-Captain
- Add fully souce code support for rk3328 including TPL/DRAM init
- Enable boot from eMMC for rk3399 rock960/ficus boards
- turn on the IO supply for dw_mmc
2019-08-09 07:29:20 -04:00
Nick Xie
a5f1249bd3 arm64: dts: rockchip: Add support for Khadas Edge-Captain
Add devicetree support for Khadas Edge-Captain.
Khadas Captain is the carrier board for Khadas Edge.

Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- SD card slot
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- Full 4 Lane M.2 Socket
- 16MB SPI Flash
- IR
- Programmable MCU

Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)

Signed-off-by: Nick Xie <nick@khadas.com>
Tested-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-05 21:12:23 +08:00
Nick Xie
6ce9ba02b1 arm64: dts: rockchip: Add support for Khadas Edge-V
Add devicetree support for Khadas Edge-V.
Khadas Edge-V is a Khadas VIM form factor Rockchip RK3399 board.

Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- SD card slot
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- Full 4 Lane M.2 Socket
- 16MB SPI Flash
- IR
- Programmable MCU

Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)

Signed-off-by: Nick Xie <nick@khadas.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-05 21:05:56 +08:00
Nick Xie
a839828fa1 arm64: dts: rockchip: Add support for Khadas Edge
Add devicetree support for Khadas Edge.
Khadas Edge is an expandable Rockchip RK3399 board with goldfinger.

Specification
- Rockchip RK3399
- Dual-Channel 2GB/4GB LPDDR4
- Onboard 16GB/32GB/128GB eMMC
- RTL8211FD 1Gbps
- AP6356S/AP6398S WiFI/BT
- HDMI Out, DP
- USB 3.0, 2.0
- USB Type C power and data
- 16MB SPI Flash
- Programmable MCU

Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2:
"arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards"
(sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e)

Signed-off-by: Nick Xie <nick@khadas.com>
Tested-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-05 21:05:29 +08:00
Tom Rini
bbaf56eda0 - sync Amlogic G12A DT with linux 5.3-rc1
- add support for 4GiB DRAM memory
 - add support for Amlogic G12B based Odroid-N2
 - small duplicate logic fix for gxbb clock driver
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAl1BkXMACgkQd9zb2sjI
 SdGd+Q/+IdXgTvox69NbfvhyA8d7GwhTWVIKgrF3NvHpxYqvvxmC7gTx1Qdh5sAO
 vyKsuygim9R/Rt7X7bzE/a1gKju/DpkxFJ0hx148xDJXmtzeBSWmDO/oOnZpUZRM
 aRUjncjxvMOZ3axtsWAZSiKqDF5i/K9Y3v/6JaLCs3WmVzlLrgANUSWqdC/Qc1Ka
 HLjem/ug3HK+o/zg0pXS3VguOTOMEV63hlWHlo2jKnxLmBpxcp1O7kH8noKR90+P
 x/byo+GAzayYv6oS0yeUz8YEXIMDVdkEX0eFzkRfe7ykz5lwGONdpLcdjmIIk6nO
 Kef7HNsRTb5ku9QPlgVLHodHNeGsV3axvmPLJQDki6/sgQmZSBWsUWPNt0yZuUjT
 gU2o7XoNmIh49hxk8ShDttGkCAYmacJwhQZ0TMV2q8q0YkDmeTWpzY5JIWq5VRLj
 0W9moxSO5SieM0FSwR/v7J2egPrz0ocOSs7XpQqH7ZNduBjq0jHwhS7Yu8wcbXTA
 baBta3tBKJhjYpfPrexrWOw1NW2fwW5kJJpnMY68nDG/ygTb++syVvTjjiqTfemI
 kIs6aBZ0AEo7WMrehdtHRFmW9SQC6h5h0Ji7bR20TigSGLe+5f0R8tASDD+0FXLB
 KID+sigdyHxM9B6uACR1pOqCjEb+IyyFXJno38v7DjaW/IoyC3k=
 =Q5fc
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-amlogic-20190731' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic

- sync Amlogic G12A DT with linux 5.3-rc1
- add support for 4GiB DRAM memory
- add support for Amlogic G12B based Odroid-N2
- small duplicate logic fix for gxbb clock driver
2019-07-31 16:06:24 -04:00
Adam Ford
b9ad74d901 Revert "ARM: davinci: da850: Manual pinmux only when PINCTRL not available"
This reverts commit 877ab2423b.

The above patch was designed to shrink code by only pin-muxing items
needed for SPL in SPL and relying on driver model or SPL to mux other
items.  Unfortunately, da850evm_direct_nor doesn't use SPL so items
that were only muxed during SPL are not muxed causing the board
to no longer boot.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-31 14:20:47 -04:00
Adam Ford
3380d1c131 ARM: da850-evm: Remove references to CONFIG_DA850_AM18X_EVM
With the removal of da850_am18xxevm, there is at least one
whitelisted CONFIG option that can be deleted.  This patch
removes CONFIG_DA850_AM18X_EVM since it's not required any more

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-31 13:08:07 -04:00
Neil Armstrong
b160fac9f7 board: amlogic: add support for Odroid-N2
ODROID-N2 is a single board computer manufactured by Hardkernel Co. Ltd
with the following specifications:

 - Amlogic S922X ARM Cortex-A53 dual-core + Cortex-A73 quad-core SoC
 - 4GB DDR4 SDRAM
 - Gigabit Ethernet
 - HDMI 2.1 4K/60Hz display
 - 40-pin GPIO header
 - 4 x USB 3.0 Host, 1 x USB OTG
 - eMMC, microSD
 - Infrared receiver

The board directory is W400, the name of the Amlogic Reference Design
of Amlogic G12B with Gigabit boards, which will be used for similar
boards.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
2019-07-31 12:10:58 +02:00
Tom Rini
476a3143d7 Xilinx/FPGA changes for v2019.10
fpga:
 - Xilinx virtex2 cleanup
 - Altera cyclon2 cleanup
 
 zynq:
 - Minor Kconfig cleanup
 - Add psu_init configuration for Z-turn board
 
 zynqmp:
 - Add support for pmufw config passing to PMU
 - script for psu_init conversion
 - zcu1275 renaming
 
 xilinx:
 - Add support for UltraZed-EV SoM
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXUBgGwAKCRDKSWXLKUoM
 IcJJAKCUoHRpqNgcZUiE10D9/VhZ3bUVtwCgi0fzSlqgHVG2EzApfqN+2KfrGJo=
 =7i0K
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2019.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze

Xilinx/FPGA changes for v2019.10

fpga:
- Xilinx virtex2 cleanup
- Altera cyclon2 cleanup

zynq:
- Minor Kconfig cleanup
- Add psu_init configuration for Z-turn board

zynqmp:
- Add support for pmufw config passing to PMU
- script for psu_init conversion
- zcu1275 renaming

xilinx:
- Add support for UltraZed-EV SoM
2019-07-30 19:19:34 -04:00
Tom Rini
dcf722ece6 Merge branch 'master' of git://git.denx.de/u-boot-sh 2019-07-30 19:19:04 -04:00
Michal Simek
cd228cc04a arm64: zynqmp: Do not include pm_cfg_obj.o when SPL is disabled
xilinx_zynqmp_mini configuration is throwing build error:
readlink: missing operand
Try 'readlink --help' for more information.

because CONFIG_ZYNQMP_SPL_PM_CFG_OBJ_FILE is not defined at all and
Makefile pass ifneq condition. Add SPL_BUILD dependency which is also
reflected in Kconfig.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-30 17:09:58 +02:00
Luca Ceresoli
216dad7507 arm64: zynqmp: add MAINTAINERS entry for Avnet UltraZed-EV
The board was added without adding a MAINTAINERS entry.

Fixes:

  $ ./tools/genboardscfg.py -f
  WARNING: no status info for 'avnet_ultrazedev_cc_v1_0_ultrazedev_som_v1_0'
  WARNING: no maintainers for 'avnet_ultrazedev_cc_v1_0_ultrazedev_som_v1_0'
  $

Reported-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-30 10:20:06 +02:00
Luca Ceresoli
ac80ac09c8 arm64: zynqmp: add support for Avnet UltraZed-EV Starter Kit
Avnet UltraZed-EV Starter Kit is composed by the UltraZed-EV SoM and the
only publicly-available compatible carrier card. The SoM is based on the EV
version of the Xilinx ZynqMP SoC+FPGA.

The psu_init_gpl.c file has been generated from the board definition files
at [0] using Vivado 2018.3 and then minimized by
tools/zynqmp_psu_init_minimize.sh. Manually removed serdes init code since
it is not mentioned in device tree and fixed a checkpatch error.

[0] 3686c9ff7d/ultrazed_7ev_cc/1.1

Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-30 10:20:06 +02:00
Anton Gerasimov
5456935a1d ARM: zynq: Add configuration for Z-turn board
Basic (PS-only) configuration based on Vivado board files by
Sergiusz Bazanski <sergius@q3k.org>

Signed-off-by: Anton Gerasimov <tossel@gmail.com>
2019-07-30 10:20:06 +02:00
Luca Ceresoli
04d2b0c7c2 arm64: zynqmp: xil_io.h: declare functions as static
Fixes sparse warnings when building zynqmp defconfigs:
  ./board/xilinx/zynqmp/xil_io.h:12:6: warning: symbol 'Xil_Out32' was not declared. Should it be static?
  ./board/xilinx/zynqmp/xil_io.h:17:5: warning: symbol 'Xil_In32' was not declared. Should it be static?
  ./board/xilinx/zynqmp/xil_io.h:22:6: warning: symbol 'usleep' was not declared. Should it be static?

Also add __maybe_unused to usleep() since it is not used by minimized
psu_init_gpl.c files, so it would warn as "defined but not used".

Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-30 10:20:06 +02:00
Luca Ceresoli
c28a9cfa40 arm64: zynqmp: spl: install a PMU firmware config object at runtime
Optionally allow U-Boot to load a configuration object into the Power
Management Unit (PMU) firmware on Xilinx ZynqMP.

The configuration object is required by the PMU FW to enable most SoC
peripherals. So far the only way to boot using U-Boot SPL was to hard-code
the configuration object in the PMU firmware. Allow a different boot
process, where the PMU FW is equal for any ZynqMP chip and its
configuration is passed at runtime by U-Boot SPL.

All the code for Inter-processor communication with the PMU is isolated in
a new file (pmu_ipc.c). The code is inspired by the same feature as
implemented in the Xilinx First Stage Bootloader (FSBL) and Arm Trusted
Firmware:

 * fb647e6b4c/lib/sw_apps/zynqmp_fsbl/src/xfsbl_misc_drivers.c (L295)
 * c48d02bade/plat/xilinx/zynqmp/pm_service/pm_api_sys.c (L357)

SPL logs on the console before loading the configuration object:

  U-Boot SPL 2019.07-rc1-00511-gaec224515c87 (May 15 2019 - 08:43:41 +0200)
  Loading PMUFW cfg obj (2008 bytes)
  EL Level:	EL3
  ...

Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-30 10:20:06 +02:00
Tom Rini
333755ef7b Merge branch '2019-07-29-ti-imports'
- More DaVinci DM migration, drop am18xx EVM platform
- Keystone bug fix
2019-07-29 17:59:15 -04:00
Bartosz Golaszewski
f99bf3b06c davinci: omapl138-lcdk: enable driver-model in SPL
Enable CONFIG_SPL_DM and enable the driver model for serial by defining
an appropriate device in the board file for da850-lcdk.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-07-29 17:58:52 -04:00
Bartosz Golaszewski
eaa381bdb4 davinci: omapl138-lcdk: remove unneeded includes
There's no SPI on da850-lcdk. Remove unnecessary includes.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-07-29 17:58:52 -04:00
Adam Ford
8dd75d3a8d ARM: da850_am18xxevm: Remove config and references
This board has been abandonded for a while.  I do not have this hardware
and nobody has appeared to notice and/or care that it's orphaned.
Since much of this code is inserted into the da850evm code base, removing
it from support will make da850evm support easier going forward.
This patch removes the da850_am18xxevm_defconfig, README references to this
board and the reference to this board from the MAINTAINERS list.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-29 17:58:47 -04:00
Tom Rini
2d64a0f7e9 Merge branch '2019-07-29-master-imports'
- Assorted bug fixes
2019-07-29 11:51:17 -04:00
Fabien Parent
bb4c5d6055 board: mediatek: Add pumpkin board support
The pumpkin board is made by Gossamer Engineering and is using
a MediaTek SoC. The board currently comes in two available version:
MT8516 SoC and MT8167 SoC.
The board provides the following IOs: eMMC, NAND, SD card, USB type-A,
Ethernet, Wi-Fi, Bluetooth, Audio (jack out, 2 PDM port, 1 analog in),
serial over USB, and an expansion header.

Additionally there is a HDMI port, DSI port, and camera port only
on the MT8167 version of the board.

The board can be powered by battery and/or via a USB Type-C port and
is using a PMIC MT6392.

The eMMC and NAND are sharing pins and cannot be used together.

This commit is adding the basic boot support for the Pumpkin MT8516
board on the eMMC.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
2019-07-29 09:32:11 -04:00
Tom Rini
ad4a699cfe - dcu and imx7 DM_VIDEO conversion
- lb070wv8 compatible in simple_panel driver
 - bmp_logo improvements for DM_VIDEO
 - EDID updates to filter supported modes
 - meson_dw_hdmi: support EDID mode filtering
 - dw_hdmi: support ddc-i2c-bus phandle for external I2C masters
 - fix rpi crash when firmware doesn't report connected display
 -----BEGIN PGP SIGNATURE-----
 
 iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXT6z3g4cYWd1c3RAZGVu
 eC5kZQAKCRBM6ATMmsalXNhfAJ9r0ewu4sKAiLZl7fcOoYYjgz30TACeIrchuxwH
 x9SiZYFntOLL0trK/O0=
 =ZsD5
 -----END PGP SIGNATURE-----

Merge tag 'video-for-2019.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-video

- dcu and imx7 DM_VIDEO conversion
- lb070wv8 compatible in simple_panel driver
- bmp_logo improvements for DM_VIDEO
- EDID updates to filter supported modes
- meson_dw_hdmi: support EDID mode filtering
- dw_hdmi: support ddc-i2c-bus phandle for external I2C masters
- fix rpi crash when firmware doesn't report connected display
2019-07-29 09:02:46 -04:00
Tom Rini
c957be9ba0 Merge tag 'u-boot-rockchip-20190729' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Clean up and migrate to use common rockchip spl board file
- Clean up and migrate to use common rockchip board file
- Increase rk3288 CONFIG_SYS_BOOTM_LEN to 16MB
2019-07-29 09:02:15 -04:00
Kever Yang
26008cd42b rockchip: rv1108: Migrate to use common board file
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29 10:27:48 +08:00
Kever Yang
8e9a8d0d0c rockchip: elgin-rv1108: use board_early_init_f for per-boar init
Use board_early_init_f() for per-board init operation and
use board_init() from common board file.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29 10:27:48 +08:00
Kever Yang
920b01388e rockchip: rk3399: Migrate to use common board file
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29 10:27:48 +08:00
Kever Yang
54b012fd96 rockchip: rk3399: init vbus regulator in board_early_init_f()
Handle per-board init in board_early_init_f() and use the
common board_init() for per-platform board init later.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29 10:27:48 +08:00
Kever Yang
edaf8db866 rockchip: rk3368: Migrate to use common board file
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29 10:27:48 +08:00
Kever Yang
38ed26777f rockchip: rk3328: Migrate to use common board file
Use common board file for board_init() and board_late_init(),
for Rockchip SoCs have very similar process.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
2019-07-29 10:27:48 +08:00
Kever Yang
271318a660 rockchip: rk3288: Move rk3288_detect_reset_reason to soc file
The rk3288_detect_reset_reason() is per-SoC operation, move
it to rk3288.c, and extend the rk_board_late_init() with
rk3288_board_late_init() to make all the board works fine
as before.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29 10:27:45 +08:00
Kever Yang
b678f2790c rockchip: rk3288: Move veyron_init() back to veyron.c
The veyron_init() should go to its board file veyron.c,
and the board_early_init_f() could be the right place.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29 10:26:41 +08:00
Kever Yang
0221910042 rockchip: rk3288: move board_early_init_f() back to veyron
The board_early_init_f() is only used by veyron board now,
move it into the board file veyron.c

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29 10:26:41 +08:00
Kever Yang
5eb9a78fcd rockchip: sdram_common: add common dram_init_banksize
dram_init_banksize() can be common used by all SoCs, move it into
sdram_common.c

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29 10:26:28 +08:00
Kever Yang
6c9a9df9f5 rockchip: clean up board_usb_init() for all SoCs
Use "snps,dwc2" for compatible name and and common variable
names so that we can share the common code for all SoCs.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29 10:25:27 +08:00
Kever Yang
faa98c7c5a rockchip: rk3399: move chromebook bob specific flow to its board file
Add a board_early_init_f() in board_init_f() and move the board
specific init code into its own board file.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29 10:25:27 +08:00
Kever Yang
8f5b5aac76 rockchip: rk3288-phycore: move phycore_init() to its own board file
phycore_init() is use for phycore board only, it should be move back
to phycore-rk3288.c

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29 10:25:27 +08:00
Kever Yang
57d55db603 rockchip: rk3288: move setup_led() to firefly-rk3288
Only firefly-rk3288 has the dts node "u-boot,boot-led",
while CONFIG_SPL_LED is not enable, move code to firefly-rk3288
now in case someone need this code.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29 10:25:27 +08:00
Igor Opaniuk
be3f1a56bf video: fsl_dcu_fb: add DM_VIDEO support
Extend the driver to build with DM_VIDEO enabled. DTS files
must additionally include 'u-boot,dm-pre-reloc' property in
soc and child nodes to enable driver binding to fsl_dcu_fb device.

Currently display timings aren't obtained from DT.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-07-29 00:09:06 +02:00
Igor Opaniuk
a6eedb670d video: fsl_dcu_fb: refactor init functions
Move dcu-related code to fsl_dcu_probe_common, keep in video_hw_init()
only legacy video stack (filling GraphicPanel struct etc.).

Add wrappers for all init functions, that will let to provide
struct fb_info as an additional param (needed for further moving it from
the global scope to driver private data struct in DM converted driver).

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-07-29 00:08:49 +02:00
Tom Rini
75551c8bfc Merge branch '2019-07-26-ti-imports'
- Bring in the rest of the J271E platform
- Various OMAP3/AM3517, DA850 fixes
2019-07-27 19:50:52 -04:00
Adam Ford
02acbb9472 ARM: am3517_evm: Fix pin muxing to enable EHCI Host in the future
This patch enables the pinmuxing to support gpio_57 for phy reset
and fixes the pinmuxing for the ECHI tranceiver.  The clocks
don't appear to by fully enabled yet, so OMAP-EHCI on am3517 is
still not yet working, but we're one step closer.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-27 13:36:52 -04:00
Adam Ford
25e4ff45b1 ARM: omap3_logic: Enable OMAP EHCI support for SOM-LV Boards
The SOM-LV boards support the OMAP EHCI driver using port 2.
With the driver updated to support device tree, this patch sets
the corresponding pin muxing for the tranceiver as well as the
reset pin.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-27 13:36:52 -04:00
Tom Rini
df9a7a195b u-boot-imx-20190719
- CCF for i.MX6
 - nandbcb command to write SPL into NAND
 - Switch to DM (i.MX28)
 - Boards: Toradex, engicam, DH
 - Fixes for i.MX8
 - Fixes for i.MX7ULP
 
 Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/561147504
 -----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAl0y6dgPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3iDYL/AgznVr7kSHoYpSGfBp8pH3R1UdUiQFg437+
 9/wqMJM5Txm1aK7qTW2u5I7qzIpGw0LMPZ7CDQhWJa1Z0hdNWf/1lMzCVOPvCl1v
 C0TK5hx3ufyfgpkGdkPvVXTmn0f8tdiqtS8zQOLVntPe5dIuOySS0MbD9K4Xewfm
 sVYO0p6F1q+EHbRGw33kIX3/ST8wuj7Iki0AFiZ2hAImHO7UeZP2X3k31kbhs+ZB
 /uhUit3Rn0nc5sIqiiP6Ptfjp8eq13LwWbSwJzezCQssmkTn14z6rrgwUcNuXNlh
 Vi88kJr2ObkFgwUpQCWss+sHzyJQkTX/iLz52FCWB4Ruzr6zGr/4ONLT/iDP0Ydl
 ncO3v8uqLpAeB7kdkt8JRJhq62qihdZc6mdN2YJoCYUZSlR3gxzKmXvT+drglsOi
 B78KoU/MgQ10REQ9IoTRLhQc1gwTF8LJSyfz5hjRGoMhD/Ek5WAQJaMlxDg67Ai8
 HB4lUNjkCV58HdP1+zIWJbbxrDc/lg==
 =LNOs
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20190719' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20190719

- CCF for i.MX6
- nandbcb command to write SPL into NAND
- Switch to DM (i.MX28)
- Boards: Toradex, engicam, DH
- Fixes for i.MX8
- Fixes for i.MX7ULP

Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/561147504
2019-07-27 09:35:05 -04:00
Adam Ford
67a4df9daf ARM: am3517-evm: Remove non-DM legacy code
With both SPL and U-Boot now supporting DM, we can start removing
legacy code.  This patch removes the legacy MMC initalization and
legacy I2C initialization since both are now available via DM and
device tree.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-26 22:24:13 -04:00
Adam Ford
e054be5bab ARM: da850-evm: Remove repeated pinmuxing calls
arch_cpu_init() initializes the pinmuxing which is called fairly
early in the start sequences, so the board_init function doesn't
need to do it again.  This patch removes the call from board_init.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-26 22:24:12 -04:00
Adam Ford
938359c570 ARM: da850-evm: Remove duplicate UART initialization
The Low Level init functions start the UART, so it doesn't need
to happen during board_init.  This patch removes it from
board_init.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-26 22:24:12 -04:00
Adam Ford
9de4695f75 ARM: am3517-evm: Remove manual ethernet reset code
The reset line going to the ethernet controller is controlled
by a global reset controlling multiple peripherals.  There
is no need to manually invoke the reset.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-26 22:24:11 -04:00
Lokesh Vutla
697a689d76 configs: j721e_evm_a72: Add initial support
Add initial defconfig support for J721e that runs on A72.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Add MAINTAINERS entry]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-07-26 22:24:00 -04:00
Lokesh Vutla
f9fe3412c6 configs: j721e_evm_r5: Add initial support
Add initial defconfig support for J721e that runs on R5.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Add MAINTAINERS file]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-07-26 22:22:14 -04:00
Suman Anna
d146af5b0e board: ti: j721e: Enable fixing up msmc sram node
Create a ft_board_setup() api that gets called as part of
DT fixup before jumping to kernel. In this ft_board_setup()
call fdt_fixup_msmc_ram that update msmc sram node.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-07-26 21:49:28 -04:00
Lokesh Vutla
f81850322a board: ti: j721e: Add board support for j721e evm
Add board specific initialization for j721e evm

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
2019-07-26 21:49:27 -04:00
Bartosz Golaszewski
e809285d49 net: davinci_emac: convert to using the driver model
Now that we removed all legacy boards selecting TI_EMAC we can
completely convert the driver code to using the driver model.
This patch also updates all remaining users of davinci_emac.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #am3517-evm & da850-evm
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2019-07-25 13:36:13 -05:00
Jianchao Wang
8782122052 Add support for the NXP LS1021A-TSN board
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.

It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.

Supported boot media: microSD card (via SPL), QSPI flash.

Rev. A of the board uses a Spansion S25FL512S_256K serial flash, which
is 64 MB in size and has an erase sector size of 256KB (therefore,
flashing the RCW would erase part of U-Boot).

Rev. B and C of the board use a Spansion S25FL256S1 serial flash, which
is only 32 MB in size but has an erase sector size of 64KB (therefore
the RCW image can be flashed without erasing U-Boot).

To avoid the problems above, the U-Boot base address has been selected
at 0x100000 (the start of the 5th 256KB erase sector), which works for
all board revisions. Actually 0x40000 would have been enough, but
0x100000 is common for all Layerscape devices.

eTSEC3 is connecting directly to SJA1105 via an RGMII fixed-link, but
SJA1105 is currently not supported by uboot. Therefore, eTSEC3 is
disabled.

Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Jianchao Wang <jianchao.wang@nxp.com>
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>

[Vladimir] Code taken from https://github.com/openil/u-boot (which
itself is mostly copied from ls1021a-iot) and adapted with the following
changes:

- Add a008850 errata workaround
- Converted eTSEC, MMC to DM to avoid all build warnings
- Plugged in distro boot feature, including support for extlinux.conf
- Added defconfig for QSPI boot
- Added the board/freescale/ls1021atsn/README.rst for initial setup
- Increased CONFIG_SYS_MONITOR_LEN so that the SPL malloc pool does not
  get overwritten during copying of the u-boot.bin payload from MMC to
  DDR.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-25 13:13:31 -05:00
Bin Meng
f588b4d205 arm: ls1021atwr: Convert to use driver model TSEC driver
Now that we have added driver model support to the TSEC driver,
convert ls1021atwr board to use it.

This depends on previous DM series for ls1021atwr:
http://patchwork.ozlabs.org/patch/561855/

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

[Vladimir] Made the following changes:
- Added 'status = "disabled";' for all Ethernet ports in ls1021a.dtsi
- Fixed the confusion between the SGMII/TBI PCS for enet0 and enet1 -
  a mistake ported over from Linux. Each SGMII PCS lies on the private
  MDIO bus of the interface (and the RGMII enet2 has no SGMII PCS).
- Added CONFIG_DM_ETH to all ls1021atwr_* defconfigs
- Completely removed non-DM_ETH support from ls1021atwr
- Changed "compatible" string from "fsl,tsec-mdio" to "fsl,etsec2-mdio"
  and from "fsl,tsec" to "fsl,etsec2" to match Linux
2019-07-25 13:13:31 -05:00
Bin Meng
49116e6d23 doc: arch: Convert README.sandbox to reST
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-24 10:10:10 -04:00
Marek Vasut
b3db7be4e3 ARM: renesas: Update Gen3 PCIe dma-ranges before boot
Update "dma-ranges" DT property of all PCIe controllers in the system
with the up-to-date DRAM layout. This allows the PCIe controller take
full advantage of all the available DRAM.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-07-23 13:38:17 +02:00
Tom Rini
79ea03b38a Merge tag 'rockchip-for-v2019.07' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- rk3399 lpddr4 support
- rk3399-rock960 board support improvement
- Eliminate pyelftools dependency by make_fit_atf.py
- clean up rockchip dts to use -u-boot.dtsi
- use ARM arch/generic timer instead of rk_timer
- clean up Kconfig options for board support
2019-07-21 15:40:21 -04:00
Chris Webb
8b1ceb0ac1 rockchip: Remove obsolete references to pyelftools
make_fit_atf.py no longer requires pyelftools, and nothing else in the
rockchip build requires it either, so remove references to installing it
from the documentation.

Signed-off-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Kever Yang
35dfc0496d rockchip: board: rk3288: remove board_boot_order()
Prefer to use dts config instead, remove all board_boot_order()
for rk3288 boards.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Ludwig Zenz
4a6f5b4f56 ARM: imx6: DHCOM i.MX6 PDK: Switch to DM for I2C
This patch enables DM I2C for DHCOM i.MX6 PDK2 boards and
removes non DM I2C code. The I2C EEPROM with ethaddr (MAC)
is defined in the device tree. Use UCLASS_I2C_EEPROM
to find the device by fixed hardware path and read the ethaddr.

Tested with DHCOM i.MX6dl and DHCOM i.MX6q.

Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2019-07-19 20:32:24 +02:00
Ludwig Zenz
6e75cb237d ARM: imx6: DHCOM i.MX6 PDK: enable pad pull ups of SS lines of spi used for boot
It turned out that after a reset the boot process from the spi bootflash is
disturbed by other spi slave devices connected to DHCOM SPI1, which uses the
same spi interface with a different SS line.

Therefore the pad pull ups are enabled.

Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
2019-07-19 20:32:24 +02:00
Marcel Ziswiler
9d364ebd05 toradex: configblock: avoid line continuations
Fix issue as reported by checkpatch.pl. Leave long lines as line
continuation in text output is not recommended.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-07-19 20:32:24 +02:00
Marcel Ziswiler
9d63c7d85c toradex: configblock: fix apalis imx8 target
The Apalis iMX8 was missing the interactive part should a customer have
bricked his module and want to re-create the configuration block. Fix
this.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-07-19 20:32:24 +02:00
Marcel Ziswiler
6c297ee832 toradex: configblock: fix colibri imx8x target
The Colibri iMX8X target got re-named late in the cycle which we forgot
to reflect here. Furthermore, it was missing the interactive part should
a customer have bricked his module and want to re-create the
configuration block. Fix this.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-07-19 20:32:24 +02:00
Marcel Ziswiler
d1aa1444e4 toradex: configblock: generic wi-fi/bt handling
Make the interactive Wi-Fi/BT handling generic by pulling it out of the
Colibri iMX6ULL interactive part to be re-used for Apalis iMX8 and
Colibri iMX8X.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-07-19 20:32:24 +02:00
Stefan Agner
42a4f18255 toradex: configblock: initialize MMC before switching partition
If the module is in serial downloader mode, we do no longer read the
environment from eMMC. Therefor, the eMMC is unitialized when trying
to read the config block. Use mmc_init to initialize the selected
MMC device before using it.

Note: In case the MMC has already been initialized, the mmc_init
detects that and returns immediately.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-07-19 20:32:24 +02:00
Ludwig Zenz
8039211a8a ARM: imx6: DHCOM i.MX6 PDK: config SPL to load U-Boot fitImage with mulitple DTs
Configure fitImage for U-Boot with a device tree for imx6 quad/dual
and duallite/solo. This enables to support the imx6 derivates
quad/dual/duallite/solo with a single binary.

Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2019-07-19 20:32:24 +02:00
Marek Vasut
4ca99fe81a ARM: imx: dh-imx6: Enable DM regulator
Enable DM support for regulators and fixed regulator driver and
convert USB Vbus control over to the regulators defined in DT.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Ludwig Zenz <lzenz@dh-electronics.com>
2019-07-19 20:14:50 +02:00
Shyam Saini
b798b8bac6 board: engicam: Remove bogus check for mmc for imx6ul isiot
imx6ul-isiot-mmc.dts was removed in uboot version v2018.03 and from then
onwards IMX6UL isiot uses imx6ul-isiot-emmc.dts for mmc, so remove
unnecessary check for mmc.

Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
2019-07-19 20:14:50 +02:00
Breno Matheus Lima
821d8d32cb mx6sxsabresd: imximage.cfg: Handle the CONFIG_SECURE_BOOT case
Secure boot is not enabled in mx6sxsabresd imximage.cfg, add support
for it.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-07-19 20:14:50 +02:00
Anatolij Gustschin
d87b2486e6 arm: imx8: don't duplicate build_info()
Move build_info() to common place.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-07-19 20:14:50 +02:00
Anatolij Gustschin
64b5f46975 arm: imx8: factor out uart init code
New imx8 boards started adding duplicated UART init code.
Factor out this to common function sc_pm_setup_uart().

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-07-19 20:14:50 +02:00
Joris Offouga
e4258ddd59 pico-imx7d: Enable DM_USB
This patch enable usb support with device-tree

Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
2019-07-19 20:14:50 +02:00
Lukasz Majewski
41d185d142 ARM: display5: Remove U_BOOT_DEVICE definition of serial_mxc
Before the wide DM/DTS adoption in the U-Boot proper, the display5
has been using only DM_SERIAL to provide serial console in
pre-relocation.

After moving to full DM/DTS adoption in the U-Boot proper the
U_BOOT_DEVICE definition is not needed anymore, as it has been
replaced with udevice creation from provided DTS description.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-07-19 20:14:50 +02:00
Lukasz Majewski
ad31f656ae ARM: display5: Fix CS check after moving some SPI related CONFIGs to Kconfig
After commit 14453fbfad ("Convert CONFIG_SF_DEFAULT_* to Kconfig")
and commit abe66b1b5d ("Convert CONFIG_ENV_SPI_* to Kconfig") ,which
moved some SPI related CONFIG_* defines to Kconfig the display5 board has
become unbootable as the SPI CS check condition had wrong value.

This commit fixes this check and allows proper SPI NOR flash operation in
SPL.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-07-19 20:14:50 +02:00
Sébastien Szymanski
f6771083a6 opos6uldev: remove board_ehci_hcd_init function
This function sets the polarity of the PWR signal which is not used on
the opos6uldev board. Remove it.

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-07-19 20:14:50 +02:00
Ye Li
06fc74102a mx7ulp_evk: Update DDR freq to 352.8Mhz for ULP B0
On i.MX7ULP B0, the DDR clock target is increased from 320Mhz to 380Mhz.
We update DDR clock relevant settings to approach the target. But since the
limitation on LCDIF pix clock for HDMI output
(refer "mx7ulp_evk: Change APLL and its PFD0 frequencies"), we set DDR
clock to 352.8Mhz (25.2Mhz * 14) by using the clock path:

	APLL PFD0 -> DDR CLK -> NIC0 -> NIC1 -> LCDIF clock

To reduce the impact to entire system, the NIC0_DIV and NIC1_DIV are kept,
so the divider 14 is calculated as:
	14 = (NIC0_DIV + 1) * (NIC1_DIV + 1) * (LCDIF_PCC_DIV + 1)

	NIC0_DIV:      1
	NIC1_DIV:      0
	LCDIF_PCC_DIV: 6

APLL and APLL PFD0 settings:

	PFD0 FRAC:  27
	APLL MULT:  22
	APLL NUM:   1
	APLL DENOM: 20

This patch applies the new settings for both DCD and plugin.
There is no DDR script change on this new frequency.
Overnight memtester is passed.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-07-19 20:14:50 +02:00
Ye Li
9c1563e3fd mx7ulp: Select the SCG1 APLL PFD as a system clock source
Due to the APLL out glitch issue, the APLLCFG PLLS bit must
be set to select SCG1 APLL PFD for generating system clock to align
with the design.

Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
2019-07-19 20:14:50 +02:00
Ye Li
285aea01d2 mx7ulp_evk: Change APLL and its PFD0 frequencies
To support HDMI display on EVK board, the LCDIF pix clock must be
25.2Mhz. Since the its PCC divider range is from 1-8, the max rate
of LCDIF PCC source clock is 201.6Mhz. This limits the source clock
must from NIC1 bus clock or NIC1 clock, other sources from APLL PFDs
are higher than this max rate.

The NIC1 bus clock and NIC1 clock are from DDRCLK whose parent source
is APLL PFD0, so we must change the APLL PFD0 and have impact to DDRCLK,
NIC1 and NIC1 bus.

Eventually, this requests to set the APLL PFD0 frequency to 302.4Mhz
(25.2 * 12), with settings:

PFD0 FRAC:  32
APLL MULT:  22
APLL NUM:   2
APLL DENOM: 5

Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-07-19 20:14:50 +02:00
Ye Li
b4bd5d71ae mx7ulp_evk: Update LPDDR3 script
Update LPDDR3 script with the changes below:
  -Update the precharge command to CMD=01 at the DDR initialization phase
  -remove unimplemented registers
   Write data bit delay --refer to the DDR_TRIM bits in
   IOMUXC1_DDR_SW_PAD_CTL_PAD_DDRn

Test:
  One EVK board passes overnight stress test.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-07-19 20:14:50 +02:00
Ye Li
72a9414bd4 mx7ulp: Fix APLL num and denom setting issue
For the current APLL setting, as we want the APLL PFD0 to meet DDR clock 320Mhz requirement.
We set MULT to 20, NUM to 4 and DENOM to 2, to get final 22 multiplier. But according to the RM,
the NUM should always be less than the DENOM. So our setting violates the rule.

Actually the ROM has already set the MULT to 22 and leave NUM/DENOM in default value. The calculated APLL PFD0 clock
is 318.9888Mhz, which also meet the DDR requirement.
To fix the issue, we remove the PLL settings in DCD to use default value from ROM, and only set the PFD0 FRAC.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-07-19 20:14:50 +02:00
Adam Ford
8f4691e31a ARM: imx6q_logic: With SPL_OF_CONTROL enabled, remove MMC init
Since the board uses SPL_OF_CONTROL now, we don't need to
explicitly initialize the MMC driver, but we still need to
pinmux the corresponding pins.  This patch removes the
initialization code and leave just the muxing behind.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-19 14:54:15 +02:00
Bhargav Shah
0b96a761c5 riscv: sifive: fu540: Enable SiFive SPI and MMC SPI drivers
This patch enables SiFive SPI and MMC SPI drivers for the
SiFive Unleashed board.

Signed-off-by: Bhargav Shah <bhargavshah1988@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-19 14:25:06 +08:00
Anup Patel
9f2a0c0f38 riscv: sifive: fu540: Setup ethaddr env variable using OTP
This patch extends SiFive FU540 board support to setup ethaddr
env variable based on board serialnum read from OTP.

Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-19 14:24:52 +08:00
Anup Patel
8633edeb2a clk: sifive: Drop GEMGXL clock driver
The GEMGXL clock driver is now directly part of Cadence MACB
ethernet driver in upstream Linux kernel. There is no separate
GEMGXL clock driver in upstream Linux kernel hence we drop
GEMGXL clock driver from U-Boot as well.

Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-19 14:24:51 +08:00
Kever Yang
f78b2ca453 rockchip: rock960-rk3399: fix mail format in MAINTAINER file
The mail format should have '<>', or else the patman won't
recognize it correctley.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Tom Rini
0de8153564 Merge branch '2019-07-17-master-imports'
- Various FS/disk related fixes with security implications.
- Proper fix for the pci_ep test.
- Assorted bugfixes
- Some MediaTek updates.
- 'env erase' support.
2019-07-18 11:31:37 -04:00
David Abdurachmanov
1493b140e4 qemu-riscv: enable VIRTIO_PCI
libvirt v.5.3.0 with QEMU 4.0.0 or above uses PCI automatically and
thus devices (network, storage, etc) are connected via PCI.

Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-18 11:31:28 -04:00
Andreas Dannenberg
03facc7271 board: ti: am654: Use EEPROM-based board detection
The TI AM654x EVM base board and the associated daughtercards have on-
board I2C-based EEPROMs containing board configuration data. Use the
board detection infrastructure introduced earlier to do the following:

1) Parse the AM654x EVM base board EEPROM and populate items like board
   name and MAC addresses into the TI common EEPROM data structure
   residing in SRAM scratch space
2) Check for presence of daughter card(s) by probing the associated
   presence signals via an I2C-based GPIO expander. Then, if such a
   card is found, parse the data such as additional Ethernet MAC
   addresses from its on-board EEPROM and populate into U-Boot
   accordingly
3) Dynamically create an U-Boot ENV variable called overlay_files
   containing a list of daugherboard-specific DTB overlays based on
   daughercards found.

This patch adds support for the AM654x base board ("AM6-COMPROCEVM")
as well as for the IDK ("AM6-IDKAPPEVM"), OLDI LCD ("OLDI-LCD1EVM")
PCIe/USB3.0 ("SER-PCIEUSBEVM"), 2 Lane PCIe/USB2.0 ("SER-PCIE2LEVM"),
and general purpuse ("AM6-GPAPPEVM") daughtercards.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-07-17 11:13:18 -04:00
Andreas Dannenberg
183fa08ae5 ti: common: am6: Add support for setting MAC addresses
The AM654x EVM based on the TI K3 family of SoCs has an updated board
detection EEPROM structure that contains a TLV record of dedicated MAC
addresses rather than a range of MAC addresses as it was used on earlier
platforms such as DRA7. Add a basic function that allows us setting up
Ethernet MAC addresses into the U-Boot environment based on the MAC
address record contained in the common TI EEPROM structure.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-07-17 11:13:18 -04:00
Andreas Dannenberg
361a53308d ti: common: am6: Add support for board description EEPROM
The AM654x EVM based on the TI K3 family of SoCs have an updated board
detection EEPROM structure, now comprising variable-sized TLV-type
records, containing a superset of what is already being provided on
earlier platforms such as DRA7. Add basic support for parsing the new
data structures contained on the base board into the common TI EEPROM
structure while also providing infrastructure that can be used later on
to parse data from additional EEPROMs such as the ones that are used on
daughtercards for this platform.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-07-17 11:13:18 -04:00
Faiz Abbas
b5d2e2980b am65x: README: Add eMMC layout and flash instructions
Add instructions for flashing boot images to the eMMC with a
layout of the address where each image needs to be flashed.

Also add instructions to flash filesystem partition in user
partition and boot kernel from the rootfs.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-07-17 11:12:54 -04:00
Andreas Dannenberg
c222e3d927 armV7R: K3: am654: Load SYSFW binary and config from boot media
Use the System Firmware (SYSFW) loader framework to load and start
the SYSFW as part of the AM654 early initialization sequence. While
at it also initialize the WKUP_UART0 pinmux as it is used by SYSFW
to print diagnostic messages.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
2019-07-17 11:12:54 -04:00
Tom Rini
0e80dda32c Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-sunxi
- Beelink-x2 STB support (Marcus)
- H6 DDR3, LPDDR3 changes (Andre, Jernej)
- H6 pin controller, USB PHY (Andre)
2019-07-16 11:19:31 -04:00
Marcus Cooper
a9e19b8ff7 sun8i: h3: Add support for the Beelink-x2 STB
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.

Linux commit details about the sun8i-h3-beelink-x2.dts sync:
"ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2"
(sha1: cc4bddade114b696ab27c1a77cfc7040151306da)

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-15 12:25:32 +05:30
Tom Rini
a9a3a37f92 - syscon: add support for power off
- stm32mp1: add op-tee config
 - stm32mp1: add specific commands: stboard and stm32key
 - add stm32 mailbox driver
 - solve many stm32 warnings when building with W=1
 - update stm32 gpio driver
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJdKK2iAAoJEOKyvdngqpN1TvcH/jj1ujNdRKn994R3DqULzFtc
 Y0WGjAciTUuV0d9gZLxPZJwlWfqxLgbmUEBlPJQJe79gaM7kNN0PgAe6GNedFhGk
 UhRR7GgbA7wogorpRo8aLe3XYEqHtgPFkf1nSiNz/AHLBg8SB20VhWcY90Kha9lh
 IJ0GK+lSdCxiyaLBC2nswnI2PS/fl4NfC7KWvujtKZduIDIOHqh5q+39llpejyuw
 WOzL/bEa4ald6JKpxOii2KXNwD1gUDQGmPzADYcIdwzJtx9hft7DBSLC5Nr+ndBz
 72TjpbtfJ/qIurv8HeXYs9mtwnCO3WP+015fog0T0zjZ48BrT1A8C96ezwLOfz0=
 =W3ny
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20190712' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm

- syscon: add support for power off
- stm32mp1: add op-tee config
- stm32mp1: add specific commands: stboard and stm32key
- add stm32 mailbox driver
- solve many stm32 warnings when building with W=1
- update stm32 gpio driver
2019-07-14 09:09:49 -04:00
Adam Ford
877ab2423b ARM: davinci: da850: Manual pinmux only when PINCTRL not available
With a recent update to the pinctrl-single driver and the fact
that the da850evm has both DM and OF_CONTROL working in both SPL
and U-Boot, some of the manual pinmuxing can be setup to only
be activated when either the driver doesn't have DM for it, or
when CONFIG_PINMUX isn't available (only during SPL).  If the
code ever shrinks enough to support PINCTRL in SPL, a lot of this
can go away.  This also remove some manual pinmuxing not needed
by SPL to give SPL a little more breathing room.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-13 11:11:29 -04:00
Niel Fourie
6e171b661e ARM: am335x: Add phyCORE AM335x R2 support
Support for Phytech phyCORE AM335x R2 SOM (PCL060) on the Phytec
phyBOARD-Wega AM335x.

CPU  : AM335X-GP rev 2.1
Model: Phytec AM335x phyBOARD-WEGA
DRAM:  256 MiB
NAND:  256 MiB
MMC:   OMAP SD/MMC: 0
eth0: ethernet@4a100000

Working:
 - Eth0
 - i2C
 - MMC/SD
 - NAND
 - UART
 - USB (host)

Device trees were taken from Linux mainline:
commit 37624b58542f ("Linux 5.1-rc7")

Signed-off-by: Niel Fourie <lusus@denx.de>
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Marek Vasut <marex@denx.de>
2019-07-13 11:11:28 -04:00
David Lechner
1d259e4d68 ARM: legoev3: convert to driver model
This converts LEGO MINDSTORMS EV3 to the driver model. MMC, SERIAL, SPI
and SPI_FLASH are converted.

The device tree contains only the minimal nodes required by U-Boot
since the size of U-Boot is limited to 256K on this device.

Signed-off-by: David Lechner <david@lechnology.com>
2019-07-13 11:11:28 -04:00
Derald D. Woods
e74e9f620a ARM: omap3: evm: Enable DM_USB in defconfig
This addresses the following warning message:

===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================

As USB support for older OMAP3 SoC's improves, OMAP3 EVM can be
readily adapted. There is some additional 'gpio-hog' support
needed to fully setup USB in a similar manner to Linux.

Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2019-07-13 11:11:27 -04:00
Ilko Iliev
26eff45737 board: pm9263: Convert to CONFIG_DM_USB and CONFIG_DM_VIDEO
Convert the board to support the USB and video driver model and remove
the unnecessary code.
2019-07-12 10:04:29 -04:00
Ilko Iliev
7a0b1f713e board: pm9261: Convert to CONFIG_DM_USB and CONFIG_DM_VIDEO
Convert the board to support the USB and video driver model and remove
the unnecessary code.
2019-07-12 10:04:29 -04:00
Patrice Chotard
291f00bb3e board: st: add missing gpio_request() for stm32f429-discovery
This fixes the following error message:

U-Boot 2019.07-rc4-00103-g5eea874b5e (Jun 25 2019 - 15:09:31 +0200)

DRAM:  8 MiB
gpio@40021800: dir_output: error: gpio GPIOG14 not reserved
gpio@40021800: dir_output: error: gpio GPIOG13 not reserved
gpio@40021800: set_value: error: gpio GPIOG14 not reserved
Flash: 2 MiB
....

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-07-12 11:50:58 +02:00
Patrick Delaunay
8e1947774e board: stm32mp1: Fix warnings when compiling with W=1
This patch solves the following warnings:

warning: no previous prototype for 'board_quiesce_devices' [-Wmissing-prototypes]
 void board_quiesce_devices(void)
      ^~~~~~~~~~~~~~~~~~~~~

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12 11:50:54 +02:00
Patrick Delaunay
e81f8d16e2 stm32mp1: activate OF_BOARD_SETUP and FDT_FIXUP_PARTITIONS
Update kernel MTD partition in device tree with U-Boot information.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12 11:50:53 +02:00
Patrick Delaunay
152c84bce9 stm32mp1: add configuration op-tee
Add support of Trusted boot chain with OP-TEE
- reserved 32MB at the end of the DDR for OP-TEE

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12 11:50:52 +02:00
Patrick Delaunay
25d436a624 stm32mp1: cosmetic: remove unnecessary include
Remove post.h include as it is used in spl.c

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12 11:18:53 +02:00
Patrick Delaunay
526558c63b stm32mp1: update README
Add latest information and correct some information.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12 11:18:53 +02:00
Patrick Delaunay
afb0840ffa stm32mp1: add stboard command
Allow to update board identification in OTP 59.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12 11:18:53 +02:00
Patrick Delaunay
f59ad456ff stm32mp1: call regulators_enable_boot_on in board_init
U-Boot activates regulators by reading the "regulator-boot-on"
property in DT; it is requested by M4 early Boot feature.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12 11:18:53 +02:00
Patrick Delaunay
4048e171d2 stm32mp1: move CONFIG_ENV in Kconfig
Move 2 ENV configuration flags in board Kconfig
- CONFIG_ENV_SECT_SIZE
- CONFIG_ENV_OFFSET

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12 11:18:53 +02:00
Tom Rini
a9758ece08 - Sandbox improvements including .dts refactor
- Minor tracing and PCI improvements
 - Various other minor fixes
 - Conversion of patman, dtoc and binman to support Python 3
 -----BEGIN PGP SIGNATURE-----
 
 iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl0nbDoRHHNqZ0BjaHJv
 bWl1bS5vcmcACgkQfxc6PpAIreZcBQgAn+ojgq/hD89bihuhz2oEe6rhzHB9OkcC
 sHrVL8Jbmby/BuzISGe4oeeM5yVygBVtUiN/72JiiAHLmykqc4CpRjNvgOOAgKCy
 Ml8UyiBNNVNfrD6f9PxAKvPZf6S0gfLnomGOQ/psdEojpY5AvQxQ36D+QFZ0AMP5
 67/xjSfN9bNPw8UbgE/VhJ+WFbU948BP2EBt6+NBAtv7HW4AX9vT0famJfWEjwq8
 ftmcFOSNGgYcDQ5BwQWX1sFhnwb9XSfurlQsVYBsFA4cx4gj0DfUm1Ugr4wDD+lo
 91P+76hSBQ+mHp1HJ90WMd2vAaElG7/SoaicXo9pW6Rc7WIgTjk7gg==
 =SdZy
 -----END PGP SIGNATURE-----

Merge tag 'dm-pull-9jul19-take2' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm

- Sandbox improvements including .dts refactor
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
2019-07-11 18:10:11 -04:00
Pascal Linder
fd9d70d738 km/spi: remove deprecated SPI flash driver code for KM Kirkwood boards
KM Kirkwood boards now implement the driver model for its SPI flash
interface. Therefore, the old board specific claim and release functions
can be deleted. The preprocessor definition CONFIG_SYS_KW_SPI_MPP is yet
unused as well. All its appearances and dependencies are removed in the
kirkwood_spi driver, header files and finally the configuration whitelist.

Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-07-11 10:58:03 +02:00
Pascal Linder
c2cd4ec00c km/spi: activate driver model for SPI flash on KM Kirkwood boards
The corresponding configurations are selected in the common Kconfig file.
This is easier than changing every affected board default configuration
file. The default configuration for the PORTL2 board, however, still needs
some modifications to correctly use the driver model.

Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-07-11 10:58:03 +02:00
Pascal Linder
53c3050d0d km/spi: overwrite kirkwood_spi weak functions for KM Kirkwood boards
As the SPI NOR and NAND devices share the same hardware pins, the MPP
configuration has to be changed when claiming/releasing the bus. The
current configuration is saved when claiming and restored when releasing.
Furthermore, a general-purpose output is used to switch the chip-select
signal. This is now also implemented for the DM part of the kirkwood_spi
driver.

Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-07-11 10:58:03 +02:00
Pascal Linder
c0fed3ac25 km: modify Kconfig file organization for KM boards
As preparation for the upcoming transferring of configurations from header
files to Kconfig, a common Kconfig file for all KM boards was created. For
the moment, it only sources the other three, more specific, Kconfig files.
Therefore, the architecture Kconfig files now include the common Kconfig
file. Also, the configuration selection for KM boards was moved from the
architecture Kconfig files to the board specific Kconfig files.

Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-07-11 10:58:03 +02:00
Marek Behún
6165c89128 arm: mvebu: turris_omnia: fix rescue mode bootcmd bootargs setting
Rescue mode bootcmd currently only appends the "omniarescue" parameter
to the bootargs variable. We do not want the user to be able to change
rescue mode bootargs. Therefore change this so that bootcmd sets the
bootargs variable in an absolute way (adding console device information
and the omniarescue paramterer).

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-07-11 10:58:02 +02:00
Marek Behún
02aa5af922 arm: mvebu: turris_omnia: call pci_init from board init code
We always want to enumerate PCIe devices, because withouth this they
won't work in Linux.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-07-11 10:58:02 +02:00
Marek Behún
b0045b1c11 arm: mvebu: turris_omnia: fix adapters MAC addresses
The board code reads MAC addresses from the ATSHA204A cryptochip.
For compatibility reasons the ethernet adapters on this SOC are not
enumerated in register address order. But when Omnia was first
manufactured this was done differently.

Change setting of MAC addresses to conform to the description on the
stickers sticked on actual Omnias.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-07-11 10:58:02 +02:00
Baruch Siach
85fe44105a arm: mvebu: clearfog: document boot from SATA
Document the main U-Boot image offset when booting from SATA disk on the
Clearfog board.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-07-11 10:58:02 +02:00
Simon Glass
80b7cb8c32 sandbox: Add documentation on how to run valgrind
U-Boot sandbox can run with valgrind to check memory allocations. Add
documentation on how to do this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2019-07-10 16:52:58 -06:00
Simon Glass
e8a7b3051b sandbox: Allo sdl-config to be overridden
When cross-compiling, sometimes sdl-config must come from a different path
from the default. Add a way to override it, by adding SDL_CONFIG to the
environment before building U-Boot.

Signed-off-by: Simon Glass <sjg@chromium.org>
2019-07-10 16:52:58 -06:00
Tom Rini
b4944e2574 First set of u-boot-atmel features and fixes for 2019.10 cycle
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJdJEZEAAoJEB6zHgIOrC/I+LAH/jUDQpF5I68h0ZFGm3xoyGhm
 3CSv8viOm/kL+GLubjnv4cwAp8N8VRpeJekz0Jt1Xp8C6OIgtnJ2Fln72KD+Z0IC
 Rq7ByRS16iq4b6IUDRZObE4Jzxmf7rXU3jr0+/vd/en7kxVlvA9+Gsffs3OTGxC7
 z9PysRZPBMH/smIPXdEQxYifnbpDG4fmfGcUWKrYfkB0Kq6Ep98Ia/gXNCY8XJ/A
 sbNQGjJWJZWXS/TDetcC2VikssJ+yNFF34uzV+HD5Y3DW6ywLhuoDOz1pg8RR36i
 YjcTCQz8lL/UVaUzrGUgPVAC3gdKY6J26GtV3vZavxBcmtGf0FhVtXO/tZc9AsY=
 =6G45
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-atmel-2019.10-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel

First set of u-boot-atmel features and fixes for 2019.10 cycle

This includes the Atmel QSPI driver and support for the at91 boards.
This is the port of the driver from Linux, mostly done by Tudor Ambarus.
2019-07-09 08:17:12 -04:00
Tudor Ambarus
ff352ac853 configs: sama5d27_som1_ek: add qspiflash_defconfig
Add the default config file of QSPI media. The config is based on
sama5d27_som1_ek_mmc_defconfig.

Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-09 09:26:43 +03:00
Tudor Ambarus
9ee8e7aec7 configs: sama5d2_xplained: add qspiflash_defconfig
Add the default config file of QSPI media. The config is based on
sama5d2_xplained_mmc_defconfig.

Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-09 09:26:43 +03:00
Tom Rini
0b7f1a95df - fix khadas-vim README
- add support for unique generated MAC adresses from SoC serial,
   limited to Amlogic GXL/GXM boards for now
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJdHgg6AAoJEHfc29rIyEnRjVkP/RmwsBgIdn/0LnuU5JQIcmNI
 S8fOV2u5YY4q4hX/5qgg6uN7/yONtiZjw4bxLJGLCj0SUQ6Tv8KgE+Jh1vswek6P
 ceOsIBfyg3ZX6INkH/moHH8/yl1NpirYjNGxw1Bg9ctBHPR9smQdh50pMyDy67mG
 E2Dja/TtOuggF6N98WSu1jB8UBA55CbEEBj1PkQt7K9bXJs9cEGSrpyZLEJvsRmL
 Pot1l1A9XKhRS3PylgoxmXWNXFD8wAk8LHEACUsxnybiWoIW5Dfao/4PSmPigXAp
 n9V3tU/OQECar0CKOtCod5pS5z8TVPuuaay/Y/+ijLlCktJBwkSaGWIhf9ILOjOW
 UTlcsFDR4KDqaEFKNDoOtOGYpczFrduU0b1hq1qu4hLV7YIxg738DoRr30JM5Lwa
 gJbUCHkPRnxVB3UztsctmQwZwfKmAdvd1CrzKqFBvemrQrf2AwfBweiAv8/AUzqq
 c7o0K0WdP/03CkmBU8KbyFn2N1X2VT1KlqgEVfRTq7UWTiLnS4j9AAiwNapGOb4M
 Ox7eODLbLw3UyZYjDuBHyPYa8uPhtVDpuFCPn2JnwFdbnT4kfE535pCKT/vbasYd
 0UQkgUPoIHm0VGhxv0hkjmrjqgv5CLQyAYhJVGATTH0Nc9dYGFKF/Gm6YIUpjUuW
 nhSh5HHVCg4dkogiMJ7u
 =BL1s
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-amlogic-20190704' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic

- fix khadas-vim README
- add support for unique generated MAC adresses from SoC serial,
  limited to Amlogic GXL/GXM boards for now
2019-07-08 16:02:19 -04:00
Tom Rini
f5e73a34ed Merge tag 'mmc-6-23' of https://github.com/MrVan/u-boot
- Pull in the series to split fsl_esdhc for i.MX/non-i.MX cleanly
2019-07-08 15:59:41 -04:00
Neil Armstrong
1f83431f00 board: amlogic: add mailing-list to MAINTAINERS
Add missing mailing-list to the amlogic boards MAINTAINERS file.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-07-04 11:36:52 -04:00
Neil Armstrong
3f1f9f08eb board: amlogic: Generate unique MAC address for Q200 and P212 based boards
Enable unique MAC address generation for boards usins SoCs having
a known functional and valid unique serial number.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-07-04 16:04:59 +02:00
Andreas Färber
aca71d6927 board: amlogic: vim: Fix README
Unlike the BayLibre repos Khadas' repo defaults to using native gcc,
so specify the CROSS_COMPILE setting matching the prescribed toolchain.

Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-07-04 16:04:59 +02:00
Fabio Estevam
4d981f5f27 wandboard: README: Adjust the U-Boot proper binary name
After the conversion to DM the U-Boot proper binary name
is 'u-boot-dtb.img', so adjust it accordingly.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-07-04 14:19:49 +02:00
Fabio Estevam
5b85858251 wandboard: Add FIT image support
After the transition to DM, only the mx6dl/solo wandboard
is supported.

Add FIT image support so that all the wandboard variants
can be supported, like it was prior to the DM conversion.

Successfully booted Linux on mx6q/solo/qp wandboards.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-07-04 14:19:49 +02:00
Tom Rini
5c74868c9f Second set of u-boot-atmel fixes for 2019.07 cycle
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJdGaVcAAoJEB6zHgIOrC/Ic1oH/3Hu55HbHVnA2QqRof/o6RnZ
 VNJQ11+Zs7QA7TIMT/Z5j9ohX0pEkVPQziD9zAL1rz7WJ/laYkPh8wqsKWmfFD2j
 2mCCnf8/vGvST8fiSv0BQ6cqozdMwdQjQ08Eqw0srJhCzqj/I8o8MNlts+OAXNIM
 CyT7LdIr/QSO05zDYxFibki4qs7Q5S8WXbtjsmbAAYajcet5w5+hEZRAD2YXuUv8
 TBuBWz6bgcSLbV7E7YXexoffgIha2K3ETAxWraKZLcc96MNLL054uBraa3dmybqZ
 +0+PHIOcNk2JR4BQmUHCoNgEuKTBPlayxZ3hVUzWzUwot4gBRRUFu/pbnRtLcF4=
 =RzN7
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-atmel-fixes-2019.07-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel

Second set of u-boot-atmel fixes for 2019.07 cycle
2019-07-01 07:31:26 -04:00
Tom Rini
0352e878d2 Fixes for 2019.07
- menlo board
 - allow SDB on Sabre
 - HAB for mx6sl
 - apalis board
 -----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAl0VwBcPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3k4AL/iaMEhY5e43krMSmlnWDfS2DsTVpyUBX1Q7X
 JHkuKQ8iH3bBSquwLNFju2hGNK8whCHfsIB5QgSh4uK3JIzWAh+/5TCGXbPDkGMJ
 PI/hyxKy2EB245SMshcJMHbyLK6PeHi4V/WA4WyY2c91Dz/DNx7UhMZOlFm8wyMl
 TwDCwtlqHodz0tXKUziCjSqTfxj7WSThwuyQ0SEHAccglM1MzM1JHq1RcdV7Pjdh
 bDpMC0rjcxYl5MM7gIig5OMtx+26HgP6JM+QfeoEuBm0PbhxV6ZFyHlafb8W/ba0
 SjzMWIknZWYA9GTAkdUgN+E0ChZVID0oSVoVh51eKiOG1z+LpkJEKE7xsaCAeBiQ
 BupLRgd0tBtqVK345EFDCy5UkYrnkLOnI+3JQNZ9bxBoPmKAf6wvhqa9Jf3bc+rP
 iSYh9Lm3sWVlXKcLR4ltS39D48OT8GZqun8zLpZkwpAWxRMuFvR+R7Q+VMVKmEF2
 1dn3EJhMsvbmTj0lYRp+ObEEpJDL9A==
 =DFoX
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20190628' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

Fixes for 2019.07

- menlo board
- allow SDB on Sabre
- HAB for mx6sl
- apalis board
2019-06-28 08:00:22 -04:00
Marek Vasut
f0be8ff45f ARM: imx: m53menlo: Convert to DM VIDEO
Enable DM Video support on iMX53 M53Menlo and fix minor details
to restore previous behavior of the system.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-06-28 00:08:42 +02:00
Marek Vasut
86aa7103b6 ARM: imx: m53menlo: Convert MMC, USB and block to DM
Enable DM block and DM MMC and DM USB support on iMX53 M53Menlo .
Convert board code to match the DM support. This also enables DM
pincontrol to configure the SDHI pins.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-06-27 14:14:48 +02:00
Marek Vasut
9b352ae1ae ARM: imx: m53menlo: Enable DM GPIO
Enable DM GPIO support on iMX53 M53Menlo and fix up board code where
applicable. Enable MALLOC_F to let the GPIO controllers bind early on.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-06-27 14:14:37 +02:00
Fabio Estevam
36adc9a06f pico-imx7d: README: Adjust the binary name after DM conversion
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx,
so fix the README file accordingly.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Joris Offouga <offougajoris@gmail.com>
2019-06-27 14:09:28 +02:00
Eugen Hristev
ad371d8cd1 board: atmel: fix pda variable not being reset
In case someone detects a PDA and u-boot sets the 'pda' variable,
and the user does a saveenv, the pda is set in env, and if the
screen is removed, u-boot will still have in the env the 'pda'
variable, even if no screen is attached.
In order to fix this, we have to reset the 'pda' variable,
such that it's not just set if the screen is detected, but also unset
if no screen is detected.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-06-27 09:47:49 +03:00
Mark Kettenis
7c7ce3600a rockchip: rk3399: Fix enabling boot-on regulators
The new common rockchip pinctrl driver does not support explicit
requests for a particular pinctrl function.  As a result, the
board_init() function bails out early before enabling the boot-on
regulators.  Fix this by simply removing the request for pwm0, pwm2
and pwm3.  The generic DM code already does the necessary
configuration if necessary.

Reported-by: Levin Du <djw@t-chip.com.cn>
Signed-of-by: Mark Kettenis <kettenis@openbsd.org>
2019-06-26 21:11:29 +08:00
Jagan Teki
07586ee432 rockchip: rk3399: Support common spl_board_init
Support common spl_board_init by moving code from puma
board file into, common rk3399-board-spl.c.

Part of the code has sysreset-gpio, regulators_enable_boot_on
but right now only puma board is using this with relevant
config options rest remains common for all targets.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-06-26 21:11:28 +08:00
Jagan Teki
9f5a9f9ad3 board: rk3399: Drop explicit uart enablement in spl_board_init
preloader_console_init is used for printing SPL boot banner that
usually called from spl_board_init.

The current spl_board_init in evb and rock960 is enabling explicit
pinctrl, debug uart prior to calling preloader_console_init which
eventually not required since board_init_f is already enabled
debug uart.

So, drop those explicit enablement calls from  spl_board_init of
evb, rock960.

Tested this by enabling CONFIG_SPL_BOARD_INIT and adding
u-boot,dm-pre-reloc property for uart node.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-06-26 21:11:27 +08:00
Jagan Teki
1c281dc2ba Kconfig: Add u-boot.itb BUILD_TARGET for Rockchip
Add u-boot.itb BUILD_TARGET for Rockchip platform when SPL_LOAD_FIT
is being used.

This can get rid of building itb explicitly with 'make u-boot.itb'
so, from now all required images will build just by make.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-06-26 21:11:27 +08:00
Jagan Teki
2411c335b6 board: puma: Get bl31.bin via BL31 and rk3399m0.bin via PMUM0
Right now puma rk3399 board need to copy bl31-rk3399.bin and
rk3399m0.bin into u-boot source directory to make use of building
u-boot.itb.

So, add environment variable
- BL31 for bl31.bin (instead of bl31-rk3399.bin to compatible with other
  platform BL31 env)
- PMUM0 for rk3399m0.bin

If the builds are not exporting BL31, PMUM0 env, the fit_spl_atf.sh will
notify with warning about which document to refer for more information
like this:

 WARNING: BL31 file bl31.bin NOT found, resulting binary is non-functional
 Please read Building section in doc/README.rockchip
 WARNING: PMUM0 file rk3399m0.bin NOT found, resulting binary is non-functional
 Please read Building section in doc/README.rockchip

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-06-26 21:11:27 +08:00
Matwey V. Kornilov
57c4c5d336 rockchip: rk3328: add rock64-rk3328_defconfig
The ROCK64 is a credit card size SBC based on Rockchip RK3328
Quad-Core ARM Cortex A53.

This series allow building u-boot SPL and u-boot.itb for Rock64
board. The proprietary TPL is stil required for deploy:

  ./tools/mkimage -n rk3328 -T rksd \
    -d ./rkbin/bin/rk33/rk3328_ddr_333MHz_v1.16.bin idbloader.img
  cat ./spl/u-boot-spl.bin >> idbloader.img
  dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc
  dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc

Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-06-26 21:11:26 +08:00
Yangbo Lu
e37ac717d7 Convert to use fsl_esdhc_imx for i.MX platforms
Converted to use fsl_esdhc_imx for i.MX platforms.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
2019-06-23 14:18:34 +08:00
Michal Simek
46e765226c arm64: zynqmp: Cover ultra96 dts file by MAINTAINERS fragment
Avnet Ultra96 dts file should be also cover by MAINTAINERS fragment.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-06-21 10:07:11 -04:00
Moses Christopher
3d2ab90d16 am335x, guardian: update the maintainer list
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
2019-06-21 10:07:11 -04:00
Masahiro Yamada
7700b13ce9 vexpress64: fix a typo of SPDX-License-Identifier
Misspelling of SPDX-License-Identifier is rather fatal than other
general typos, so must be fixed.

This file spells SPDX-Licence-Identifier.
                           ^

I also moved it to the very top of the file with // comment style.

Detected by grepping the source tree:

$ git grep --not -e SPDX-License-Identifier --and -e SPDX-
board/armltd/vexpress64/pcie.c: * SPDX-Licence-Identifier:      GPL-2.0+

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Liviu Dudau <liviu.dudau@foss.arm.com>
2019-06-21 10:07:11 -04:00
Oleksandr Zhadan
f51d7fc8ce board: Arcturus: DM: Disable drivers without DM support.
Extra "not DM" controllers support is disabled.
u-boot BSP still good enough to upgrade and run images.

Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
2019-06-21 10:07:11 -04:00
Tom Rini
f643fb9f4c Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx
- PCIe driver change to support DM model
- T2080QDS migrated to use PCIe DM model
2019-06-20 09:14:35 -04:00
Hou Zhiqiang
15311c85db powerpc: T208xQDS: Compile the legacy PCIe routines conditionally
Compile the legacy PCIe initialization reoutines only when DM_PCI
is not enabled.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-20 10:44:10 +05:30
Tom Rini
63a4585791 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq
- LS1046AFRWY support
- USB errata fix and secure boot defconfig support for LS1028A
- Enabled SDHC and SATA for LX2160
- LS1046A serdes fixes
- other minor fixes
2019-06-19 14:01:11 -04:00
Udit Agarwal
da70f766dd board/freescale/common: secure_boot: Set bootdelay to -2.
Uboot prompt must not be available while running
secure boot. TO ensure this  bootdelay must be set
to -2.

Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-19 12:54:57 +05:30
Vabhav Sharma
d90c7ac7a9 armv8: ls1046afrwy: Add support for LS1046AFRWY platform
LS1046AFRWY board supports LS1046A family SoCs. This patch
add base support for this board.
Board support's 4GB ddr memory, i2c, micro-click module,microSD card,
serial console,qspi nor flash,ifc nand flash,qsgmii network interface,
usb 3.0 and serdes interface to support two x1gen3 pcie interface.

Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-19 12:54:57 +05:30
Yuantian Tang
a1e126bf8d armv8: ls1028a: Add secure boot defconfig
Add secure boot defconfig for ls1028aqds and ls1028ardb boards.

Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-19 12:54:57 +05:30
Mian Yousaf Kaukab
de0f9ad1de board: lx2160a: fix fsl-mc status in fdt with bootefi
fsl-mc lazyapply command applies dpl from efi_exit_boot_services().
Status of fsl-mc node in working fdt is updated at this stage.
However, an efi application like grub may already have copied the fdt.
So the updates to fdt done at efi_exit_boot_services() may not be
visible to the OS. Fix it by updating fdt earlier if fsl-mc lazyapply
command is used.

Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-19 12:54:57 +05:30
Pankaj Bansal
1be0c66c79 board/fsl/layerscape: Modify the aliases names
when compiling dts file using DTC_FLAG='-@', the device tree compiler
reports these warnings:

Warning (alias_paths): /aliases: aliases property name must include
only lowercase and '-'

Fixed the node aliases to silence these warnings.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-19 12:54:56 +05:30
Tom Rini
c3f43185ee Merge branch 'master' of git://git.denx.de/u-boot-spi
- Drop zipitz2 board (Tom)
- Add DEPRECATED option (Tom)
- Mark legacy or non-dm drivers as DEPRECATED (Jagan)
2019-06-17 11:32:22 -04:00
Tom Rini
8f93213227 Merge branch 'master' of git://git.denx.de/u-boot-sh
- More board removal
2019-06-15 13:02:12 -04:00
Ramon Fried
0dfe442e87 MAINTAINERS: change Ramon Fried email address
Change my email address, too many mails
gets to my private mail, created specific email
account just for developmement.

Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2019-06-14 10:09:15 -04:00
Marek Vasut
a7e3dacbcb sh: r0p7734: Remove the board
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
2019-06-14 12:42:06 +02:00
Marek Vasut
c81b1a8a71 sh: ap325rxa: Remove the board
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
2019-06-14 12:42:06 +02:00
Marek Vasut
52883bac27 sh: ap_sh4a_4a: Remove the board
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
2019-06-14 12:42:06 +02:00
Marek Vasut
94bb4492e1 sh: ms7750se: Remove the board
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
2019-06-14 12:42:06 +02:00
Marek Vasut
6b371a7a4b sh: ms7722: Remove the board
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
2019-06-14 12:42:06 +02:00
Marek Vasut
ea349270e3 sh: espt_giga: Remove the board
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
2019-06-14 12:42:06 +02:00
Tom Rini
88369d33e3 configs: Disable now unbuildable SPI options for boards
Now that various SPI related options depend on CONFIG_DEPRECATED, in
order for platforms to build out of the box they need to disable various
other options.

Cc: Albert ARIBAUD <albert.aribaud@3adev.fr>
Cc: Marek Vasut <marex@denx.de>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-06-13 12:51:06 +05:30
Tom Rini
9a4b90015a arm: Remove zipitz2 board
Per discussion on the list, drop this board again.

Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-06-13 12:50:55 +05:30
Tom Rini
2702646bc0 - Add Ethernet support for STM32MP1
- Add saveenv support for STM32MP1
 - Add STM32MP1 Avenger96 board support
 - Add SPI driver suport for STM32MP1
 - Add watchdog support for STM32MP1
 - Update power supply check via USB TYPE-C for STM32MP1 discovery board
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJc+TqsAAoJEMrHeC97M/+miKwP/3OouX3slblEfUELRj/9qLlU
 ypdUDKDQupGSrTIyhJHFdGbA2ct/ERl4mH/kU8NNeCHVCsdvrrmuw+k4jfVZfIyi
 d9gWmU5WanNPzdWwdo0NrVNXjN5LPduxeUCYHdDEggDJuG3YL4LA9pPyrWpL8o8t
 tLPr8YMB1u5Ab8Vn/1A9lKvmw98V59LmWVxZh0AtAdOTvWgEZQe1R5Vex+MHacnK
 uR/Dm3ry5v7ZlR/kMZ0C+Ip1aw9GU4e+O+LCGlU4Jr0GV2XQOr4ehxWtN02nYubc
 sYXbkW7UArR0I0g8YPXPoBI9PToi57bHW/TXKoI8yDIll7vZ9PDjT/FbUJM9rv72
 WU6T7+K2DeHflmp4NljiesD2rDnti0XSCbe4o5o/jD+YkzH6YoJbco4nsae7TBSM
 R3rgV7/+St7zC1IjFq0TUG+S9qSUmZqA4k66+j5/SS6pLQOW3dYemL0/up2cRX5w
 dx00JTQkHyh7Q/GfH8r7yZqIToW9djB9HeT88ovPUCh8rVfDqNn8/WKd2JAfkxda
 QiZDs49BMBsnWpK+vPqiq/suoJeSwDB70iMzrGgBg+mTd9eJcD0c5QBURYE0jm2H
 GqQ04WNi8sLzULhMqKbBdPZhBMzyNmDXF6MC+y/OcUM5k8z6tY8LDro3wgHXWVpX
 DLiFVbkHbLhlUJbeO8dD
 =2C9f
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20190606' of https://github.com/pchotard/u-boot

- Add Ethernet support for STM32MP1
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
2019-06-11 17:22:22 -04:00
Tom Rini
529faf80c3 u-boot-imx-20190612
--------------------
 
 - Board fixes:
 	- imx6logic
 	- wandboard
 	- mx6sabre boots again
 	- imx8qm_mek
 	- pico-* boards
 	- Toradex apalis / colibri
 	- engicam imx6 (environment)
 	- KP MX53
 	- opos6ul
 - Switch to DM:
 	- vining2000
 	- dh MX6
 	- Toradex colibri i.MX7
 	- Novena
 - Security : fix CSF size for HAB
 - Other:
       - imx: fix building for i.mx8 without spl
       - pcie and switch to DM
 
       mx6sabreauto: Enable SPL SDP support
 -----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAlz/bLMPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3W7oL/1rYXpSr2JE8fdXvqtmugjaPr7lQFzE7Bjkw
 pDyDZA+3tpG8lv5xwjUi0Q+c38RRY6K/1lP/bztGXal+ryx/V0HFNAKKdhzedxhy
 kgB3BGyp0rdEpzRwBLEkUCVFKJyVMI9ztPpzun6FDm+pyvIN4vnvziYPlkrYSyVk
 ZrvCGk6X8OYAJ3qNcTcttPIXTfv0QTs8l6bpw3kHSVoUSAGGQc2FxOUmxvwsZedN
 jpVJ5iB/2xrmSyWMIcGAfXLhzNolooeFgcqdKj7X+x0l0Q1p/S4srGKfYRqqhsAO
 q4H/Xjt47e6oWVclbh3TypnUuxAw0i2BhhczAbr/nnN42aNySWrtQyZm33h/esAy
 dcriYUvHlsoC00sfB1xShF4rhBno8OW+ExJVDwsVMalJr9WI4FujwsE/Aw+CUec8
 ompz1IUz+2+BG+PcVbDNxysM5TcqpdQOaq0JKQUnz/xzyocV75M2pFw9YzQE85J7
 yHAoq5OlW//B1wSRuPlH3vBkVWf2SA==
 =pRXQ
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20190612' of git://git.denx.de/u-boot-imx

u-boot-imx-20190612
--------------------

- Board fixes:
	- imx6logic
	- wandboard
	- mx6sabre boots again
	- imx8qm_mek
	- pico-* boards
	- Toradex apalis / colibri
	- engicam imx6 (environment)
	- KP MX53
	- opos6ul
- Switch to DM:
	- vining2000
	- dh MX6
	- Toradex colibri i.MX7
	- Novena
- Security : fix CSF size for HAB
- Other:
      - imx: fix building for i.mx8 without spl
      - pcie and switch to DM

      mx6sabreauto: Enable SPL SDP support
2019-06-11 13:41:24 -04:00
Fabio Estevam
e0e5f6da6e imx8mq_evk: Staticize when appropriate
Staticize 'spl_dram_init' and 'i2c_pad_info1' to fix the
following sparse warnings:

board/freescale/imx8mq_evk/spl.c:30:6: warning: symbol 'spl_dram_init' was not declared. Should it be static?
board/freescale/imx8mq_evk/spl.c:41:22: warning: symbol 'i2c_pad_info1' was not declared. Should it be static?

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-06-11 10:43:00 +02:00
Marek Vasut
74ae372ae4 ARM: imx: vining2000: Enable DM Serial
Enable DM Serial support on iMX6SX VINING|2000.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-06-11 10:42:48 +02:00
Marek Vasut
0e0d38f49b ARM: imx: vining2000: Enable DM GPIO
Enable DM GPIO support on iMX6SX VINING|2000 and fix up
board code where applicable.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-06-11 10:42:48 +02:00
Marek Vasut
ac2b71f60b ARM: imx: vining2000: Convert MMC and block to DM
Enable DM block and DM MMC support on iMX6SX VINING|2000 .
Convert board code to match the DM support. This disables
USB mass storage support due to missing DM USB, however
that will be re-enabled in subsequent patch.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-06-11 10:42:48 +02:00
Marek Vasut
4c05e966fd ARM: imx: Rename VINING|2000
The company Samtec was merged into Softing, migrate the board over to
the new name and update copyright headers.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-06-11 10:42:48 +02:00
Christoph Fritz
d57863087b mx6sx: vining2000: pinmux usdhc4 reset
This patch configures pinmux for pin usdhc4 reset.

Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
2019-06-11 10:42:48 +02:00
Fabio Estevam
934f9a653c mx6sabresd: Remove U-Boot proper mmc initialization
After the conversion to DM there is no need to have mmc initialization
code inside U-Boot proper.

Remove the unneeded code.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-06-11 10:42:48 +02:00