For the TI SoCs affected by errata i2329, enable MDIO manual
mode by default
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
In certain TI SoCs, on the CPSW and ICSS peripherals, there is
a possibility that the MDIO interface returns corrupt data on
MDIO reads or writes incorrect data on MDIO writes. There is also
a possibility for the MDIO interface to become unavailable until
the next peripheral reset.
The workaround is to configure the MDIO in manual mode and disable the
MDIO state machine and emulate the MDIO protocol by reading and writing
appropriate fields in MDIO_MANUAL_IF_REG register of the MDIO controller
to manipulate the MDIO clock and data pins.
More details about the errata i2329 and the workaround is available in:
https://www.ti.com/lit/er/sprz487a/sprz487a.pdf
Add implementation to disable MDIO state machine, configure MDIO in manual
mode and provide software MDIO read and writes via MDIO bitbanging. Allow
the MDIO to be initialized based on the need for manual mode.
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Here are the smatch warning messages:
drivers/net/xilinx_axi_emac.c:324 axiemac_phy_init()
error: 'phydev' dereferencing possible ERR_PTR()
drivers/net/zynq_gem.c:340 zynq_phy_init()
error: 'priv->phydev' dereferencing possible ERR_PTR()
Fix by adding error checking before dereferencing the pointer.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20220929045605.23964-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The maximum length is capped similarly to the emaclite_send function.
Avoid integer underflow for values of ip->ip_len < 30, the minimum
length of an IP packet is 21 bytes.
Signed-off-by: Samuel Obuch <samuel.obuch@codasip.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Link: https://lore.kernel.org/r/20220927112103.155689-3-samuel.obuch@codasip.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Use __raw_read* and __raw_write* functions to ensure read/write
is passed to the memory-mapped regions, as non-volatile accesses
may get optimised out.
Signed-off-by: Samuel Obuch <samuel.obuch@codasip.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Link: https://lore.kernel.org/r/20220927112103.155689-2-samuel.obuch@codasip.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Function ioremap_nocache seems to be defined only for MIPS and Microblaze
architectures. Therefore, the function call in the emaclite driver causes
this driver to be unusable with other architectures, for example RISC-V.
Use ioremap function instead of ioremap_nocache, and include linux/io.h
instead of asm/io.h, so that ioremap function is automatically created,
if not defined by the architecture. We can switch to the ioremap function,
as Microblaze's ioremap_nocache is just empty and in MIPS implementations
of ioremap_nocache and ioremap are the same.
Signed-off-by: Samuel Obuch <samuel.obuch@codasip.com>
Link: https://lore.kernel.org/r/20220927112103.155689-1-samuel.obuch@codasip.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This patch adds support for MediaTek MT7981 and MT7986. Both chips uses
PDMA v2.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for PDMA v2 hardware. The PDMA v2 has extended the
DMA descriptor to 8-words, and some of its fields have changed comparing
to the v1 hardware.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch is a preparation for adding a new version of PDMA of which the
DMA descriptor fields has changed. Using bitfields will result in a complex
modification. Convert bitfields to u32 units can solve this problem easily.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Using a single soc id to control different initialization and TX/RX flow
for all SoCs is not extensible if more hardware variations are added in
the future.
This patch introduces a struct to replace the original mtk_soc to allow
the driver be able handle newer hardwares.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
Fman microcode is executable code (AFAICT) loaded into a
coprocessor. As such, if verified boot is enabled, it must be verified
like other executable code. However, this is not currently done.
This commit adds verified boot functionality by encapsulating the
microcode in a FIT, which can then be signed/verified as normal. By
default we allow fallback to unencapsulated firmware, but if
CONFIG_FIT_SIGNATURE is enabled, then we make it mandatory. Because
existing Layerscape do not use this config (instead enabling
CONFIG_CHAIN_OF_TRUST), this should not break any existing boards.
An example (mildly-abbreviated) its is provided below:
/ {
#address-cells = <1>;
images {
firmware {
data = /incbin/(/path/to/firmware);
type = "firmware";
arch = "arm64";
compression = "none";
signature {
algo = "sha256,rsa2048";
key-name-hint = "your key name";
};
};
};
configurations {
default = "conf";
conf {
description = "Load FMAN microcode";
fman = "firmware";
};
};
};
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Several ethernet drivers load firmware from FIT images. Convert them to
use the fit_get_data helpers.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If ethernet connected to SFP, like this:
&enetc_port0 {
phy-connection-type = "sgmii";
sfp = <&sfp0>;
managed = "in-band-status";
status = "okay";
};
Then enetc_config_phy returns -ENODEV and the memory containing the mdio interface is freed.
It's better to unregister and free mdio resources.
Signed-off-by: Siarhei Yasinski <siarhei.yasinski@sintecs.eu>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The deadline for DM_ETH migration passed 2 years ago. Now that
platforms which cannot be migrated have been either removed or had
drivers disabled, and platforms that needed minor help to migrate have
been forcefully migrated, we can complete the migration.
This entails select'ing DM_ETH under NETDEVICES, and then removing now
extraneous depends on lines. In a few places, we can now either remove
options or just simplify later dependencies.
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
As this driver has been converted to DM_ETH and the migration deadline
is 2 years passed, remove the legacy code and callers.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
When using DM_ETH, which should be the default now, we need to always
have DM_MDIO and FSL_LS_MDIO enabled, so select them.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Wasim Khan <wasim.khan@nxp.com>
Cc: Udit Agarwal <udit.agarwal@nxp.com>
Cc: Ashish Kumar <Ashish.Kumar@nxp.com>
Cc: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Manish Tomar <Manish.Tomar@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver has not been converted to DM_ETH. The migration
deadline passed 2 years ago.
Cc: Trevor Woerner <twoerner@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
This driver has not been converted to DM_ETH. The migration deadline
passed 2 years ago.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Liviu Dudau <liviu.dudau@foss.arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
This converts the following to Kconfig:
CONFIG_FSL_NGPIXIS
CONFIG_SYS_FSL_QMAN_V3
CONFIG_SYS_FSL_RAID_ENGINE
CONFIG_SYS_FSL_RMU
CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
CONFIG_SYS_FSL_SRIO_LIODN
CONFIG_SYS_FSL_TBCLK_DIV
CONFIG_SYS_FSL_USB1_PHY_ENABLE
CONFIG_SYS_FSL_USB2_PHY_ENABLE
CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE
CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
Signed-off-by: Tom Rini <trini@konsulko.com>
This allows you to specify the type of rgmii-id that will enable phy
internal delay in ethernet phy-mode.
This adds all RGMII cases to all of get_pinmode() except LD11, because LD11
SoC doesn't support RGMII due to the constraint of the hardware. When RGMII
phy mode is specified in the devicetree for LD11, the driver will abort
with an error.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
We check if phydev is NULL. Only but if it is non-NULL we set one
component of phydev. But even if it is NULL we set another. We should not
dereference NULL in either case.
Fixes: e24b58f5ed ("net: phy: don't require PHY interface mode during PHY creation")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reorder include files in the U-Boot expected order.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The convinience functions are not that small and they caused
bloated text segments because of their usage.
There was no need to inline them in the first place, as
they're not part of a fastpath.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Previously we'd been using a device name retrieved via
ftgmac100_data->phydev, but the mdio read/write functions may be
called before that member is initialized in ftgmac100_phy_init(),
leading to a NULL pointer dereference while printing the error message
issued if the mdio access fails. We can instead use bus->name, which
is already available at that point.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 538e75d3fc ("net: ftgmac100: add MDIO bus and phylib support")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
NPCM750 provides identical ethernet MAC controllers for WAN/LAN applications.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Only two boards in the tree set the macro DWC_NET_PHYADDR. Both have
CONFIG_DM_ETH_PHY=y, so should set the phy address in DT if necessary.
The imx8mp_evk does set the correct address in device tree.
The other board seems to be a copy-paste-adapt from an old
version of the imx8mp_evk config header, given the "#ifdef
CONFIG_DWC_ETH_QOS" block that has been removed from imx8mp_evk header
in commit 127fb45495. Its device tree doesn't even enable (i.e., set
'status = "okay"') the &eqos node. But the other ethernet device,
&fec, does get enabled, and does have a phy sitting at address 4 (and
it also has a corresponding legacy #define CONFIG_FEC_MXC_PHYADDR
4). So I believe it should be completely safe to remove it from there
as well.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[trini: Re-apply to top of tree, update imx93_evk.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
I have an iMX8MP with a ti,dp83867 phy in front of the eqos
interface. The phy is Gbit capable - however, the C and D differential
pairs are not physically routed to the RJ45 connector. So I need to
prevent the phy from advertising 1000Mbps.
The necessary code is almost already there in the form of a
phy_set_supported() call in eqos_start(), but the max-speed DT
property is currently only parsed in
eqos_probe_resources_stm32(). Lift that parsing to eqos_probe().
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Not only does eqos_remove() fail to free the buffers that have been
allocated by eqos_probe_resources_core(), it repeats those allocations
and thus drops twice as much memory on the floor.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Assign packet pointer only in case the MAC reports anything in the FIFO.
In case the MAC indicates empty FIFO, return 0 to pass that information
to the network stack.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This patch adds basic support for the Marvell 88E1240 PHY.
This will be used by the upcoming ethernet support addition for the
Marvell MIPS Octeon EBB7304 platform.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
This patch adds support for the "marvell,reg-init" DT property, which
is used to describe board specific Marvell PHY register configurations
in the board dts file. This DT property is supported in the Linux Kernel
since a longer time. Adding it to U-Boot now, enables the boards which
describe the register settings in their DT files here as well.
I've included calling this marvell_of_reg_init() to all foo_config()
functions in this patch as well. If CONFIG_DM_ETH is not set, there is
no ofnode, or no "marvell,reg-init" property, the PHY initialization is
unchanged.
The function marvell_of_reg_init() is a port of the Linux version.
Please note that I explicitly did not add error checking and handling
to the U-Boot version, as this is basically not done for phy_read/write
in this Marvell PHY code.
This will be used by the upcoming ethernet support on the MIPS
Octeon EBB 7304 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Since new atheros PHY driver needs to access its PHY node through
phy device, we have to assign the phy node in ethernet controller
driver. Otherwise the PHY driver will fail to get some nodes
and properties.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move i.MX code to a standalone file to make it easy for adding new
platform support
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move macros and structures to header file and make some functions
public, so that could used by other files, this is to
prepare split platform specific config to one file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When CONFIG_CLK is not enabled, there will be buil break:
"error: ‘eqos’ undeclared (first use in this function)"
Take eqos definition out the CONFIG_CLK ifdef.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This header is not used since commit abdbefba2a ("net: sun8i_emac: Use
consistent clock bitfield definitions"). Dropping it allows the driver
to be architecture-independent.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
