Add missing board/ti/common/Kconfig references for the platforms that
missed it. The intent is for the common Kconfig to be usable across TI
reference boards as required.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
i.MX93 uses the same USB IP as i.MX8MM. It can then reuse the ehci-mx6
driver.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Additional testing of the changes introduced in commit 33e06dcbe5 "common:
usb-hub: Reset hub port before scanning") revealed that some USB 2.0 and 3.0
flash drives didn't work in U-Boot on some Allwinner SoCs that support USB
2.0 interfaces only. More precisely, some of the tested USB 2.0 and 3.0
flash drives failed to be detected and work on an OrangePi Zero 3, based on
the Allwinner H616 SoC that supports USB 2.0 only, while the same USB flash
drives worked just fine on a Pine64 H64, based on the Allwinner H6 SoC that
supports both USB 2.0 and USB 3.0 interfaces.
The USB ID of the above-mentioned USB 3.0 flash drive that failed to work is
1f75:0917 (Innostor Technology Corporation IS917 Mass storage), it is 32 GB
in size and sold under the PNY brand. The mentioned USB 2.0 drive is some
inexpensive no-name drive with an invalid USB ID.
Resetting USB 3.0 hubs only, which this patch introduces to the USB hub
resets, has been tested to work as expected, resolving the identified issues
on the Allwinner H616, while not introducing any new issues on other tested
Allwinner SoCs. Thus, let's fix it that way.
According to the USB 3.0 specification, resetting a USB 3.0 port is required
when an attached USB device transitions between different states, such as
when it resumes from suspend. Though, the Linux kernel performs additional
USB 3.0 port resets upon initial USB device attachment, as visible in commit
07194ab7be63 ("USB: Reset USB 3.0 devices on (re)discovery") in the kernel
source, to ensure proper state of the USB 3.0 hub port and proper USB mode
negotiation during the initial USB device attachment and enumeration.
These additional types of USB port resets don't exist for USB 2.0 hubs,
according the USB 2.0 specification. The resets seem to be added to the USB
3.0 specification as part of the port and device mode negotiation.
The Linux kernel resets USB 3.0 (i.e. SuperSpeed) hubs only, as visible in
commit 10d674a82e55 ("USB: When hot reset for USB3 fails, try warm reset.")
in the kernel source. The check for SuperSpeed hubs is performed in a way
that also applies to newer SuperSpeed Plus (USB 3.1 or 3.2) hubs as well,
which hopefully makes it future proof.
Fixes: 33e06dcbe5 ("common: usb-hub: Reset hub port before scanning")
Link:
https://lore.kernel.org/u-boot/20240207102327.35125-1-i@shantur.com/T/#u
Link:
https://lore.kernel.org/u-boot/20240201164604.13315fa6@donnerap.manchester.arm.com/T/#u
Signed-off-by: Shantur Rathore <i@shantur.com>
Helped-by: Dragan Simic <dsimic@manjaro.org>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Marek Vasut <marex@denx.de>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/19683
- Convert msc_sm2s_imx8mp to DM_SERIAL.
- Make Ethernel functional on msc_sm2s_imx8mp.
- General improvements for msc_sm2s_imx8mp.
- Add suport for the Sielaff i.MX6 Solo board.
- Update GE HealthCare maitainers' e-mail addresses.
The Sielaff i.MX6 Solo board is a control and HMI board for vending
machines. Add support for this board.
The devicetree files are taken from pending changes in the Linux
kernel that are available from linux-next and will likely be
part of Linux v6.9.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Update our email addresses, from @ge.com to @gehealthcare.com, after GE
HealthCare was spun-off from GE.
Remove Antti, who no longer works on the project.
Signed-off-by: Ian Ray <ian.ray@gehealthcare.com>
There is no imx8mp-msc-sm2s.dtb file in upstream Linux.
Change it to imx8mp-msc-sm2s-ep1.dtb.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Ian Ray <ian.ray@gehealthcare.com>
Redundant environment support is required for software updates.
Add support for it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Ian Ray <ian.ray@gehealthcare.com>
Add mmc alias so that the eMMC is mmc0 and the SD card
is mmc1 to have a well defined device numbering scheme.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Ian Ray <ian.ray@gehealthcare.com>
Currently, the Ethernet ports are not working.
The Ethernet PHY reset lines are controlled by the TCA6424 I2C GPIO
expander.
The TCA6424 I2C GPIO expander is supported by the CONFIG_DM_PCA953X
driver.
Select the CONFIG_DM_PCA953X option so that the Ethernet PHYs can
go through a proper reset making Ethernet to be functional.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Ian Ray <ian.ray@gehealthcare.com>
The conversion to DM_SERIAL is mandatory, so do the conversion.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Ian Ray <ian.ray@gehealthcare.com>
Enable LTO globally on Renesas R-Car platforms. This has been enabled
on a subset of boards already, but at this point it is safe to enable
it globally. This saves units or tens of kiB from the resulting build.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The maximum size of u-boot.img on R-Car Gen2 is 0x80000 or 512 kiB,
set the limit to avoid overflows as new functionality gets pulled in.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
These systems are unlikely to use EFI as this functionality has not been
enabled until it got pulled in by Kconfig default. This functionality
does add some 60-70 kiB to the u-boot.img size, which overflows the size
limit. Disable it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
To prepare support for multiple register layouts pointers to register
tables where added to struct cpg_mssr_info. These pointers are suppose
to be filled in at probe time and no intended change in behavior was
intended.
However the new pointers where only filled in by some paths of the
driver implemented in clk-rcar-gen3.c. The path implemented in
clk-rcar-gen2.c was not updated leaving the pointers uninitialized
leading to a crash when trying to probe the clocks.
Fix this by filling in the pointers in the Gen2 code path with the
values used before they where moved to struct cpg_mssr_info.
Fixes: d413214fb7 ("clk: renesas: Add register pointers into struct cpg_mssr_info")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # R8A7791 Porter
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
u-boot-dfu-20240215
- Fix avb_verify command with SD cards
- Add u-boot-dfu maintainer tree for AB/AVB
- Avb: report verified boot state based on lock state
- Misc avb refactors improve code quality
Use existing str_avb_slot_error() function for obtaining
verification fail reason details.
Take into account device lock state for setting correct
androidboot.verifiedbootstate kernel cmdline parameter.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Link: https://lore.kernel.org/r/20240209192045.3961832-7-igor.opaniuk@foundries.io
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Introduce str_avb_io_error() and str_avb_slot_error() functions,
that provide a pointer to AVB runtime error message.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Link: https://lore.kernel.org/r/20240209192045.3961832-6-igor.opaniuk@foundries.io
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Simplify and add more context for prints where it's needed.
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240209192045.3961832-5-igor.opaniuk@foundries.io
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Make error prints more verbose with additional context.
Also s/print/debug/g for prints, which might be relevant only
for debugging purposes.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Link: https://lore.kernel.org/r/20240209192045.3961832-4-igor.opaniuk@foundries.io
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Move SPDX license identifiers to the first line, so it conforms
to license placement rule [1]:
Placement:
The SPDX license identifier in kernel files shall be added at the first
possible line in a file which can contain a comment. For the majority
of files this is the first line, except for scripts which require the
'#!PATH_TO_INTERPRETER' in the first line. For those scripts the SPDX
identifier goes into the second line.
[1] https://www.kernel.org/doc/Documentation/process/license-rules.rst
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Link: https://lore.kernel.org/r/20240209192045.3961832-3-igor.opaniuk@foundries.io
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
mmc_switch_part() is used for switching between hw partitions
on eMMC (boot0, boot1, user, rpmb).
There is no need to do that for SD card.
This fixes the avb command usage on SD cards.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20240209192045.3961832-2-igor.opaniuk@foundries.io
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This message isn't an error (there can be a watchdog subnode for example)
but it shouldn't be printed unless this driver is being debugged. Demote
it to a debug print.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
- Add the button command patch, update MAINTAINERS entry for a platform,
fix a problem with the hash command, fix a problem on K3 platforms and
revert a change on verdin-am62.
With the relatively new button API in U-Boot, it's now much easier to
model the common usecase of mapping arbitrary actions to different
buttons during boot - for example entering fastboot mode, setting some
additional kernel cmdline arguments, or booting with a custom recovery
ramdisk, to name a few.
Historically, this functionality has been implemented in board code,
making it fixed for a given U-Boot binary and requiring the code be
duplicated and modified for every board.
Implement a generic abstraction to run an arbitrary command during boot
when a specific button is pressed. The button -> command mapping is
configured via environment variables with the following format:
button_cmd_N_name=<button label>
button_cmd_N=<command to run>
Where N is the mapping number starting from 0. For example:
button_cmd_0_name=vol_down
button_cmd_0=fastboot usb 0
This will cause the device to enter fastboot mode if volume down is held
during boot.
After we enter the cli loop the button commands are no longer valid,
this allows the buttons to additionally be used for navigating a boot
menu.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Tegra30
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
AM64 ES2.0 bootrom seems to enable WAIT0EDGEDETECTION interrupt.
This causes a lockup at A53 SPL when accessing NAND controller
or ELM registers.
A good option would be to softrest GPMC block at probe
but this cannot be done for AM64 as SOFTRESET bit is marked
as reserved in SYSCONFIG register.
Fix the issue by disabling all IRQs at probe.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Add myself as co-maintainer for Poplar board, as I'm currently
working on it (re-testing releases, addressing issues etc).
CC: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
CC: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz@gmail.com>
Some platforms (such as the Lichee Pi 4A) have their dwmac device
addressable only in high memory space. Storing the node's base address
on 32 bits is not possible in such case.
Use platform's physical address type to store the base address.
Signed-off-by: Nils Le Roux <gilbsgilbert@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Rework the section about includes slightly. We should not be using
common.h anywhere, so remove that from examples and ask people to send
patches removing it when found. Doing this also means we need to reword
other parts of this section. Be clearer about using alphabetical
ordering.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
The error message
Adding disk for usb_mass_storage.lun0 failed (err=-9223372036854775788/0x8000000000000014)
provides a decimal and a hexadecimal notation of the EFI status code
EFI_ALREADY_STARTED which is defined as (EFI_ERROR_MASK | 20).
The decimal output does not convey the value 20 clearly.
With the patch we write
Adding block device usb_mass_storage.lun0 failed, r = 20
similar to other EFI error messages.
Fixes: 952018117a ("dm: sandbox: Switch over to using the new host uclass")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
