Current driver always performs a phy soft reset when connecting the phy
device, but soft reset is not always supported by a phy device, so
introduce a quirk PHY_FLAG_BROKEN_RESET to let such a phy device to skip
soft reset. This commit uses 'flags' of phy device structure to store the
quirk.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The picoseconds to register value divisor(ps_to_regval) should be 60 and not
200. Linux has KSZ9031_PS_TO_REG defined to be 60 as well. 60 is the correct
divisor because the 4-bit skew values are defined from 0x0000(-420ps) to
0xffff(480ps), increments of 60.
For example, a DTS skew value of 420, represents 0ps delay, which should be 0x7.
With the previous divisor of 200, it would result in 0x2, which represents a
-300ps delay.
With this patch, ethernet on the SoCFPGA DE0 Atlas is now able to work with
1Gb ethernet.
References:
http://www.micrel.com/_PDF/Ethernet/datasheets/KSZ9031RNX.pdf -> page 26
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use the 'autoneg' flag available in phydev when checking if
autoneg is in use.
The previous implementation was checking directly in the PHY
if autoneg was supported. Some PHYs will report that autoneg
is supported, even when it is disabled. Thus it is not possible
to use that bit to determine if autoneg is currently in use or
not.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When configuring a PHY in fixed (forced) link mode, in order for
the changes to be applied, either one of these conditions must
be triggered:
1- PHY is reset
2- Autoneg is restarted
3- PHY transitions from power-down to power-up
Neither of these is currently done, so effectively the fixed link
configuration is not applied in the PHY.
Fix this by setting the Autoneg restart bit.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Micrel PHYs KSZ8021/31 and KSZ8081 have a feature where MDIO address 0
is considered as a broadcast address; the PHY will respond even if it
is not its configured (pinstrapped) address. This feature is enabled
by default.
The Linux kernel disables that feature at initialisation, but not
before it probes the MDIO bus. This causes an issue, because a PHY
at address 3 will be discovered at addresses 0 and 3, but will then
only respond at address 3. Because Linux attaches the first PHY it
discovers on 'eth0', it will attach the PHY from address 0, which
will never answer again.
Fix the issue by disabling the broadcast feature in U-Boot, before
Linux is started.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This new function will allow MAC drivers to override supported
capabilities of the phy. It is required when MAC cannot handle all
speeds supported by phy.
For example phy supports up-to 1Gb connections while MAC may only work
in modes up to 100 or even 10 Mbit/sec.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
of_set_phy_supported allows overwiting hardware capabilities of
a phy with values from the devicetree. This does not work with
the genphy driver though because the genphys config_init function
will overwrite all values adjusted by of_set_phy_supported. Fix
this by initialising the genphy features in the phy_driver struct
and in config_init just limit the features to the ones the hardware
can actually support. The resulting features are a subset of the
devicetree specified features and the hardware features.
This is a copy of the patch from Linux kernel, see
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=c242a47238fa2a6a54af8a16e62b54e6e031d4bc
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When a Gigabit PHY device is connected to a 10/100Mbits capable Ethernet
MAC, the driver will restrict the phydev->supported modes to mask off
Gigabit. If the Gigabit PHY comes out of reset with the Gigabit features
set by default in MII_CTRL1000, it will keep advertising these feature,
so by the time we call genphy_config_advert(), the condition on
phydev->supported having the Gigabit features on is false, and we do not
update MII_CTRL1000 with updated values, and we keep advertising Gigabit
features, eventually configuring the PHY for Gigabit whilst the Ethernet
MAC does not support that.
This patches fixes the problem by ensuring that the Gigabit feature bits
are always cleared in MII_CTRL1000, if the PHY happens to be a Gigabit
PHY, and then, if Gigabit features are supported, setting those and
updating MII_CTRL1000 accordingly.
This is a copy of patch from Linux kernel, see
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=5273e3a5ca94fbeb8e07d31203069220d5e682aa
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When doing a software reset, the reset flag should be written without
other bits set. Writing the current state will lead to restoring the
state of the PHY (e.g. Powerdown), which is not what is expected from
a software reset.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Michael Welling <mwelling@ieee.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 08ad9b068a (" ar8031: modify the config func of ar8031 to
ar8021_config") selected 'ar8021_config' as the configuration function
for AR8031.
The correct would be to use 'ar8035_config' instead as AR8031/AR8035
have the same programming model and even share the same phy driver
in the linux kernel: drivers/net/phy/at803x.c.
Tested on a mx6qsabresd and wandboard, which now can work without
any PHY setup code in the board files.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add code to process the KSZ9021/KSZ9031 OF props if they are present
and configure skew registers based on the information from the OF.
This code is only enabled if the DM support for ethernet is also
enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
V2: - Implement struct ksz90x1_reg_field to describe the skew register
fields more accurately.
- Fix RXDV/TXEN skew register default value and offset.
The phy can share driver with other aquantia PHYs, so we only
add PHY ID.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Code is taken from Linux kernel driver (v4.2).
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
-> Add National instrument ethernet transceiver configuration used (DP83848)
-> Change cpsw slave phy address
-> modify nand configuration to use the correct ECC and correct nand features
In phy_connect_dev(), if the phy device has an accociated mac device
before, a warning message will be printed. But we should test the
old device against the new one, if they are actually the same one,
don't print the warning message.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In get_phy_device_by_mask(), when no phy is found, currently we only
print a message to show the first phy address that is not found. But
this is not always the case as multiple phys can be specified by
phy_mask. Change to print all phys that are not found, and to reduce
the console boot log, change to use 'debug' instead of 'printf'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In get_phy_device_by_mask(), when no phy is found, we should not
create any phy device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
NAND-tree is used to check wiring between MAC and PHY using NAND gates
on the PHY side, hence the name.
NAND-tree initial status is latched at reset by probing the IRQ pin.
However some devices are sharing the PHY IRQ pin with other peripherals
such as Atmel SAMA5D[34]x-EK boards when using the optional TM7000
display module, therefore they are switching the PHY in NAND-tree test
mode depending on the current IRQ line status at reset.
This patch ensure PHY is not in NAND-tree test mode only for the Micrel
KSZ8051 PHY used by Atmel. There are other Micrel PHY affected but I
doubt they are used on such weird hardware design.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds support for Micrel KSZ8021RNL & KSZ8031RNL.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently when phy device is created the link variable is
initialized to 1 which denoted phy link is already up. On a power
reset there is no issue as phy status register link status will
not be set, so phy auto negotiate will be started. But when a cpu
reset is issued (ex: dra72x-evm) phy's link status bit is already
set which leads to assume that link is already setup in
genphy_update_link() initial check which results in ehternet not
working. So do not assume that link is already up and on phy
device create set link to zero. This is verified on dra72x-evm.
Reported-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support of VSC8584 phy placed on new QSGMII/SGMII ethernet riser cards
used on LS2085QDS platforms.
Signed-off-by: King Chung Lo@freescale.com <KingChungLo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add Ethernet PHY for BCM Cygnus SoC
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
With commit e3a77218a2 the MII bus is only
reset if a reset handler is registered. If there is no reset handler there
is no need to wait for a device to come out of the reset.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Support the 88E1510 PHY which is very similar to the 88E1518.
I also set the INTn output and configured the LEDs.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- The EEE fixup magic should also be enabled for RGMII
- Improved comments
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Targets with CONFIG_NEEDS_MANUAL_RELOC do not use REL/RELA
relocation (mostly only GOT) where functions aray are not
updated. This patch is fixing function pointers passed to phy_register
function.
This patch was tested on Microblaze architecture.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
RTL8211F needs to enalbe TXDLY for RGMII during
phy initialization, so move it to rtl8211f_config
for early initialization.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
RTL8211F has different registers from RTL8211E.
This patch adds support for RTL8211F PHY which
can be found on Freescale's T1023 RDB board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix comilation warning which is emitted when
firmware address is more than 32 bit.
Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
commit 3c6928fd7b "net: phy: fix warnings with W=1" caused
some PHYs(e.g. CS4315/CS4340) not working. This patch fixes the
warning and make those special PHYs working as well.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Some Realtek Ethernet PHYs, like RTL8211D(G/N) and RTL8211E(G), have
interrupts enabled by default. If the interrupt is not treated later by
the OS and the PHY's interrupt line is enabled and shared with other
interrupts, the system will get an interrupt storm. This patch disables
the interrupt for PHY devices that use one of the current Realtek
Ethernet PHY drivers. Some of Realtek Ethernet PHYs, such as RTL8211B(L)
have the interrupt masked. In this case, the functionality of the PHY
should not be afected since this patch brings INER and INSR registers to
their default values.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When driver model is used for Ethernet a few functions are passed a udevice
instead of an eth_device. Also add a function to find a PHY type given its
name. This will be used to decode the device tree node.
Finally, put a phy_interface field in struct eth_pdata since this is an
important part of the platform data for Ethernet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds a phy driver for the Micrel KSZ8895 switch. As the SoC MAC
is directly connected to the switch MAC the link to the switch is always up.
But the KSZ8895 switch can be hardwired in three configuration modes :
- not configurable with eventually an eeprom-stored configuration
- configurable by the mdio/mdc connection (SMI protocol)
- configurable by a SPI connection.
In not configurable mode, the switch starts automatically, but in the
other modes, it must be started programmatically, by writing 1 in
configuration register 1.
We only support the not configurable and mdio/mdc (aka SMI) modes here.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
This patch supports AQ1202, AQ2104, AQR105 PHY.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
VSC8514 QSGMII PHY requires enabling auto-negotiation,
otherwise it wouldn't work.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for Cortina CS4315/CS4340 10G PHY.
- This driver loads CS43xx firmware from NOR/NAND/SPI/SD device
to initialize Cortina PHY.
- Cortina PHY has non-standard offset of PHY ID registers, thus
we define own get_phy_id() to override default get_phy_id().
- To define macro CONFIG_PHY_CORTINA will enable this driver.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As per Marvell Release Notes - Alaska 88E1510/88E1518/88E1512/88E1514
Rev A0, Errata Section 3.1 Marvell PHY has an errata which requires
that certain registers get written in order to restart
autonegotiation.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
get_phy_id is marked weak but has no protype nor a
strong version, just make it static. Use __weak for
board_phy_config.
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
In case when several Ethernet ports are supported it's
convenient to see the number of phy that is not found.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Old saying says that more than three exclamation marks in a row are
sign of mental disease. Cleanup micrel.c.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Chin Liang See <clsee@altera.com>
The following configs are not defined at all:
- CONFIG_INCA_IP_SWITCH
- CONFIG_PBL2800_ETHER
- CONFIG_PHY_ICPLUS
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
get_phy_id returns -EIO when it can't read from a phy at a given addr. This would cause
create_phy_by_mask to return prematurely before it had tested the other addresses in the provided mask.
Example usage:
Replace
phydev = phy_connect(bus, phy_addr, dev, phy_if)
with
phydev = phy_find_by_mask(bus, phy_mask, phy_if)
if (phydev)
phy_connect_dev(phydev, dev);
Signed-off-by: Cormier, Jonathan <jcormier@criticallink.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
This patch adds support for VSC8664 PHY module which can
be found on Freescale's T4240RDB boards.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As some PHYs have non-standard PHY ID registers, PHY Id can't
be read correctly by current get_phy_id function, so we enable
get_phy_id redefinable to permit specific PHY driver having own
specific get_phy_id function.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
