Both PCS/PMA PHY and the external PHY need to have a valid link status
in order to have Ethernet traffic. Check and wait this status at
setup_phy() so that we could diagnose if there is a PHY issue.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Link: https://lore.kernel.org/r/20221101035800.912644-3-andy.chiu@sifive.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
If we bridge an external PHY to Xilinx's PCS/PMA PHY and would like to
get and set the real status of the PHY facing the external world. Then
we should phy_connect() to the external PHY instead of the PCS/PMA one.
Thus, we add a pcs-handle DT entry, which have been merged in Linux, and
leave the configuration of it to the driver itself.
Unlike Linux, where the PCS/PMA PHY is managed by phylink, managing the
PCS/PMA PHY is only internal to the driver in U-Boot. The PCS/PMA PHY
pressents only when the phy-mode is configured as SGMII or 1000Base-X,
so it is always 1 Gbps and full-duplex and we may skip passing link
information out.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Link: https://lore.kernel.org/r/20221101035800.912644-2-andy.chiu@sifive.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Here are the smatch warning messages:
drivers/net/xilinx_axi_emac.c:324 axiemac_phy_init()
error: 'phydev' dereferencing possible ERR_PTR()
drivers/net/zynq_gem.c:340 zynq_phy_init()
error: 'priv->phydev' dereferencing possible ERR_PTR()
Fix by adding error checking before dereferencing the pointer.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20220929045605.23964-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
CONFIG_DM_ETH_PHY enables support to utilize generic ethernet phy
framework. Though if ethernet PHY node is in other ethernet node, it
will use shared MDIO to access the PHY of other ethernet. Move ethernet
print info statement from plat function to probe function, as phyaddr is
not enumerated when CONFIG_DM_ETH_PHY is enabled.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/ecfec78234233fefdc172c141c207b2d78ef70c5.1652181968.git.michal.simek@amd.com
Rename constant PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA to make
it compatible with Linux' naming.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Add helpers ofnode_read_phy_mode() and dev_read_phy_mode() to parse the
"phy-mode" / "phy-connection-type" property. Add corresponding UT test.
Use them treewide.
This allows us to inline the phy_get_interface_by_name() into
ofnode_read_phy_mode(), since the former is not used anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
If we just use fdtdec_get_addr_size_fixed to get "reg" it will use
64bit address cell to get the base address.
soc {
#address-cells = <1>;
#size-cells = <1>;
compatible ="SiFive,FU500-soc", "fu500-soc", "sifive-soc", "simple-bus";
ranges;
L28: axidma@30010000 {
#dma-cells = <1>;
compatible = "xlnx,axi-dma-1.00.a";
axistream-connected = <&L27>;
axistream-control-connected = <&L27>;
clocks = <&L1>;
interrupt-parent = <&L6>;
interrupts = <32 33>;
reg = <0x30010000 0x4000>;
fdtdec_get_addr_size_fixed: reg: addr=3001000000004000
We should get the base address through its parent's address-cells and
size-cells settings. So we should use fdtdec_get_addr_size_auto_parent()
to get correct base address.
After applying this patch, we can get the correct base address of dma by
replacing fdtdec_get_addr_size_fixed() with
fdtdec_get_addr_size_auto_parent().
fdtdec_get_addr_size_auto_parent:
na=1, ns=1, fdtdec_get_addr_size_fixed: reg: addr=30010000
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Link: https://lore.kernel.org/r/20220120084128.1892101-1-andy.chiu@sifive.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for 10G/25G (XXV) high speed ethernet. This Makes use of
the exiting AXI DMA, similar to 1G.
Signed-off-by: Alessandro Temil <atemil@waymo.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There are lot of accesses to priv data in of_to_plat(), which is incorrect.
Create a platform data structure and use it in of_to_plat(), then copy all
platform data to priv data in probe.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
flush_cache() arguments are not type casted to take care of 64 bit
systems. Use phys_addr_t to type cast for it to work properly for 32 bit
and 64 bit systems.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
There are compilation warnings showing up when we compile AXI ethernet
driver for 64bit architectures. Fix them, so that it works on both 32
and 64 bit architectures.
DMA descriptors are not taking care of 64bit addresses. To fix it,
change axidma_bd members as below:
next ==> next_desc
reserverd1 ==> next_desc_msb
phys ==> buf_addr
reserverd2 ==> buf_addr_msb
and update next_desc and buf_addr with lower 32 bits of the addresses,
update next_desc_msb and buf_addr_msb with upper 32 bits of the 64bit
addresses.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The index used to iterate over the possible PHYs in axiemac_phy_init was an
unsigned int and decremented. Therefor it was always >= 0 and never exited
the loop.
Signed-off-by: Patrick van Gelder <patrick.vangelder@nl.bosch.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch assings the phynode pointer to the phydev node as it is needed
later in the corresponding phy driver to read phy properties from DT.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch uses writeq() function to enable greater than 32 bit
addressing of axi-ethernet for the ZynqMP devices.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
wait_for_bit callers use the 32 bit LE version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch uses readl and writel instead of in_be32 and
out_be32 for io ops as these internally uses readl,
writel for microblaze and for Zynq, ZynqMP there is
no need of endianness conversion and readl, writel
should work straightaway. This patch starts supporting
the driver for Zynq and ZynqMP platforms.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for non processor mode, this mode doesn't have
access to some of the registers and hence this patch
bypasses it and also length has to be calculated from
status instead of app4 in this mode.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Read dma address using fdtdec_get_addr as it checks for
address cells and size cells and reads the address
properly. fdtdec_get_int always assume address is of int
size which goes wrong if using it on 64-bit architecture.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
axi_emac, emaclite and gem have the same issue with registering
multiple instances with mdio busses. mdio bus name has to be uniq but
drivers are setting up only one name for all.
Use mdio_register_seq() and pass dev->seq number to allow multiple
mdio instances registration.
Reported-by: Phani Kiran Kara <phanikiran.kara@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
axi_emac, emaclite and gem have the same issue with registering
multiple instances with mdio busses. mdio bus name has to be uniq but
drivers are setting up only one name for all.
Use mdio_register_seq() and pass dev->seq number to allow multiple
mdio instances registration.
Reported-by: Phani Kiran Kara <phanikiran.kara@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Series-to: u-boot
Series-cc: Phani Kiran Kara <phanikiran.kara@gmail.com>
In SGMII cases the isolate bit might set after DMA and
ethernet resets and hence check and clear during
setup_phy if it was set.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Pass appropriate interface type to phy_connect
instead of zero.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Also add dependency on PHYLIB and MII which is required.
Clean PHYLIB dependency from the driver too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Rename few functions to fit to the new name convention used by DM.
Suggested-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
