At present the early timer init happens as soon as driver model is set up.
This makes it impossible to do anything that needs driver model but must
run before devices are probed (as needed with Intel's FSP-S, for example).
In any case it is not a good idea to tie probing of particular drivers too
closely to the DM init.
Create a new function to init the timer and put it a bit later in the
sequence.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present these options cannot be enabled for SPL/TPL, but this can be
useful in some cases. Add Kconfig options to allow it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When device-tree compilation fails it is sometimes tricky to see which
line is broken, since the input file to dtc is a pre-processed version
of the device tree.
Add a line that points to the file that needs to be checked:
When the error is in the main .dts file, output is something like this:
output: 'Error: arch/x86/dts/.chromebook_coral.dtb.pre.tmp:478.46-47
syntax error
FATAL ERROR: Unable to parse input tree
but in fact looking at that file shows nothing useful:
PAD_CFG_NF_IOSSTATE_IOSTERM(GPIO_157, UP_20K, DEEP, NF1, HIZCRX1, DISPUPD)
Instead we need to look at the preprocessed file, which shows:
163 ((1U << 30) | (1 << 10)) ((0xb << 10) | PAD_CFG1_IOSSTATE_HIZCRX1)
Here it is clear that PAD_CFG1_IOSSTATE_HIZCRX1 is not defined and so is
not being resolved by the preprocessor.
This commit adds an additional useful message:
Check arch/x86/dts/.chromebook_coral.dtb.dts.tmp for errors
Note that if the error is reported in an included file, such as
u-boot.dtsi then the output is the following:
Error: arch/x86/dts/u-boot.dtsi:137.14-15 syntax error
FATAL ERROR: Unable to parse input tree
But again, if the error is due to a preprocessor failure, like this:
filename = CONFIG_IFW_INPUT_FILE;
then you can't tell what the problem is by looking at the source. All you
see is the original code:
intel-ifwi {
filename = CONFIG_IFW_INPUT_FILE;
...
};
};
intel-fsp-m {
filename = CONFIG_FSP_FILE_M;
};
Everything looks fine. But looking at the output of the preprocessor:
intel-ifwi {
filename = CONFIG_IFW_INPUT_FILE;
...
};
intel-fsp-m {
filename = "fsp_m.bin";
};
This shows that the filename (normally "fitimage.bin") has not been
inserted the preprocess, leading to the realisation that the value should
be CONFIG_IFWI_INPUT_FILE.
If the above does not make sense, I encourage people to try introducing
errors in the device tree preprocessed values.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Most x86 CPUs use a mechanism where the SPI flash is mapped into the very
top of 32-bit address space, so that it can be executed in place and read
simply by copying from memory. For an 8MB ROM the mapping starts at
0xff800000.
However some recent Intel CPUs do not use a simple 1:1 memory map. Instead
the map starts at a different address and not all of the SPI flash is
accessible through the map. This 'Fast SPI' feature requires that U-Boot
check the location of the map. It is also possible (optionally) to read
from the SPI flash using a driver.
Add support for booting from Fast SPI. The memory-mapped version is used
by both TPL and SPL on Apollo Lake.
In respect of a SPI flash driver, the actual SPI driver is ich.c - this
just adds a few helper functions and definitions.
This is used by Apollo Lake.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Allow this driver to set up an IO address in SPL using an 'early-regs'
property. This allows SPL to use the I2C driver without having to enable
the full PCI stack.
Also split out ofdata_to_platdata in designware driver since this is more
correct, and more convenient for the new logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Drivers are not allowed to use static data since they may be used in SPL
where BSS is not available.
It is possible that driver model may provide support for numbering devices
in the future. But for now, move this to global_data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is hacked into the driver at present. It seems better to have it as
a separate driver that uses the base driver. Create a new file and put
the X86 code into it.
Actually the Baytrail settings should really come from the device tree.
Note that 'has_max_speed' is added as well. This is currently always false
but since only Baytrail provides the config, it does not affect operation
for other devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These functions are used by code outside the network support, so move them
to lib/ to be more accessible.
Without this, the functions are only accessible in SPL/TPL only if
CONFIG_SPL/TPL_NET are defined. Many boards do not enable those option but
still want to do checksums in this format.
Fix up a few code-style nits while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Early in boot it is necessary to decode the PCI device/function values for
particular peripherals in the device tree or of-platdata. This is needed
in TPL where CONFIG_PCI is not defined.
To handle this, move pci_get_devfn() into a file that is built even when
CONFIG_PCI is not defined.
Also add a function for use by of-platdata, to convert a reg property to
a pci_dev_t.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present PCI auto-configuration happens in U-Boot both before and after
relocation. This is a waste of time and may mess up static addresses used
in board_init_f(). Adjust the code to supporting doing auto-configuration
once, after relocation, under control of a device-tree property.
This is needed for Apollo Lake for debugging the silicon-init code. Once
the UART is moved to a different MMIO address the debug UART does not work
and any debug output in Apollo Lake's arch_fsp_init_r() causes a hang.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If the offset is -1 this function correctly sets up a null ofnode. But if
the offset is any other negative number (e.g. -FDT_ERR_BADPATH) then it
does the wrong thing.
An offset of -1 in ofnode indicates that the ofnode is not valid. Any
other negative value is not handled by ofnode_valid(). We could of course
change that function, but it seems much better to always use the same
value for an invalid node.
Fix it by setting the offset to -1 if it is invalid for any reason.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
SPL and TPL can access information about binman entries using link-time
symbols but this is not available in U-Boot proper. Of course it could be
made available, but the intention is to just read the device tree.
Add support for this, so that U-Boot can locate entries.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
sandbox unicode support in serial
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl3xP/0ACgkQfxc6PpAI
reYTTAf/Uuhm4meLxXyho3zelrYZKcVtLcbQSTwwMKsfQYV/rH+Hbi7StbQSO1+K
UYt/A2O0ic0U+UiSpHv8A5n2JGzcmeJK1f6BJvyoXAhXJAxRKGQhxAAE+X/GcSi8
8gpfYEAb0Zpd+1eTBBMSWLXrFAwITbfqe45L4BcDb9BT+Dkhidr9SZQahu8xzgMa
Wf0oXUQy+HmHB6YYTUcpyUisYJV5SiuVZDqsMDJ58T/4nYKnAV2qlu647YFiWyZe
A+EeL13LbAGHibz385J5rAYb6RFM8SlWunicQnFrsYHoagfxTrrnkwF5EZdeBb1e
sCX+jNk28WbjcAN6wjDcOSKIVDQ4wQ==
=Ycht
-----END PGP SIGNATURE-----
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
i2c bugfixes for 2020.01
- i2c: i2c_cdns: fix write timeout on fifo boundary
fixes timout issue when writting number of bytes is multiple
of the FIFO depth.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJd77jyAAoJEB6zHgIOrC/IyYUH/iAUH4wo5qnOBiQU+MJluaiu
D8tMiJH13eW4gWnAqdGrOE9Q763asHIMshQpLK+4eXe4f4mZQ7re4CRNcYJrULeY
2StsJzl4sn/H4P5EiRuUWjkB7wnGRDD6ArH3j1uMJN4lpwCB0ZbqMQZpjt3wI2H4
KuE42d/ll08Aj0AvwdusffLIxlw5M1Z94uQSHoC3UTkPYN4VD5zXgdxv5eH6PZWe
paWmHQ0g7fL4UnYGWa0Jpx10SZpcut06dTeVGpsGiEOhaJHvpjYd4JAs/TTUxhFx
d5ZRjo1fStYmBXQIblhPNlJQkW4cqa/B+81f5aZbN/1yCijJWS2G8anGtY2ikPs=
=f0dF
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2020.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
- First set of u-boot-atmel fixes for 2020.01 cycle:
This set includes a small fix for gpio bank names, one for removing
unused headers (also touches some other boards), and a fix for the QSPI
env read on one of the boards.
The rpi_4_32b_defconfig states that only one DRAM bank is present. This
leads to a wrong configuration of the available DRAM. Fix this by
setting the DRAM bank config accordingly.
Fixes: 193279d784 ("RPI: Add defconfigs for rpi4 (32/64)")
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Up to now we only update the DRAM banks when we are define
CONFIG_BCM2711. But our one binary approach uses a config that supports
BCM2837 and BCM2711. As a result we only see one gibibyte of RAM on
Raspberry Pi 4, even if it has more RAM.
Fix this by calling dram_init_banksize.
Fixes: 5694090670 ("ARM: defconfig: add unified config for RPi3 and RPi4")
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
To update the dram bank information from device-tree we use
fdtdec_decode_ram_size() which expectes the the size-cells and
address-cells to be defined in the memory node. For normal system RAM
these values are defined in the root node. When the values differ from
the default values defined in the spec, we can end up with wrong RAM
bank information.
Switch to the "standard" way to update the RAM bank information to
avoid this.
Fixes: 9de5b89e4c ("rpi4: enable dram bank initialization")
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This fixes an issue that would cause I2C writes to timeout when the
number of bytes is a multiple of the FIFO depth (i.e. 16 bytes).
Within the transfer loop, after writing the data register with a new
byte to transfer, if the transfer size equals the FIFO depth, the loop
pauses until the INTERRUPT_COMP bit asserts to indicate data has been
sent. This same check is performed after the loop as well to ensure data
has been transferred prior to returning.
In the case where the amount of data to be written is a multiple of the
FIFO depth, the transfer loop would wait for the INTERRUPT_COMP bit to
assert after writing the final byte, and then wait for this bit to
assert once more. However, since the transfer has finished at this
point, no new data has been written to the data register, and hence
INTERRUPT_COMP will never assert.
Fix this by only waiting for INTERRUPT_COMP in the transfer loop if
there's still data to be written.
Signed-off-by: Michael Auchter <michael.auchter@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Chromium EC commands can be up to 16-bits, so using a uint8_t here can
cause truncation. Update to use a uint instead.
It looks like this should likely have been done as a part of
9fea76f5d3, but this function was skipped
for some reason.
Signed-off-by: Michael Auchter <michael.auchter@ni.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Today when parsing the .sizes files we get a warning about an invalid
line in the file as it's blank. Solve this by checking that we have a
non-blank line prior to processing.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sometimes it is useful for external tools to use buildman to provide the
toolchain information. Add an -a option which shows the value to use for
the ARCH environment variable, and -A which does the same for
CROSS_COMPILE
Signed-off-by: Simon Glass <sjg@chromium.org>
At present buildman looks at toolchains, then commits and then boards.
Move the board processing up above the commit processing, since it relates
to the toolchain code. This will make it easier to check the toolchains
needed for a board without processing commits first.
Signed-off-by: Simon Glass <sjg@chromium.org>
We don't really need buildman to print this every time it runs. Add a flag
to run quietly, that buildman can use.
Signed-off-by: Simon Glass <sjg@chromium.org>
bigger than the framebuffer resolution
- reduce dead code in video and console uclass routines
(tested on mx53cx9020, sama5d2_xplained, stm32mp157c-ev1,
stm32f746-disco, stm32f769-disco and wandboard)
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXe//LA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXOqBAJ9N6oTID0v092duxoUoO5xAeqIKxgCfS/YvgGx4
KGgiPWQv0V1bGxXyYNA=
=PoNP
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-2020.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix crash and board reset when drawing RLE8 bitmaps
bigger than the framebuffer resolution
- reduce dead code in video and console uclass routines
(tested on mx53cx9020, sama5d2_xplained, stm32mp157c-ev1,
stm32f746-disco, stm32f769-disco and wandboard)
Buildman doesn't store this file in the same directory as a normal build.
Update the conftest code to handle both cases.
Change-Id: I1fd0e56054d7dc77394a7589336aa0991bd0133d
Signed-off-by: Simon Glass <sjg@chromium.org>
The parser responsible for the '[make-flags]' section in
the '.buildman' settings file is currently not able to
handle quoted strings, as given in the sample bellow:
[make-flags]
qemu_arm=HOSTCC="cc -isystem /add/include" HOSTLDFLAGS="-L/add/lib"
This patch replaces the simple string splitter based on the <space>
delimiter with a regex tokenizer that preserves spaces inside double
quoted strings.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Due to a conversion error the sandbox does not accept byte values 0x80-0xff
from the keyboard. The UEFI extended text input unit test requires Unicode
support.
Use unsigned char for the serial buffer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
In the device tree UEFI unit test the compatible property of the device is
read.
Provide the missing property.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In the initial SPI flash setup, the default bus mode being used was 3,
which is incorrect, causing a CRC error when the ENV was being read from
QSPI. Setting the default bus mode to 0 which is the correct mode.
Signed-off-by: Swapna Gurumani <swapna.gurumani@microchip.com>
- Increase stack size to avoid a stack overflow during distro boot.
- Add hifive-unleashed-a00.dts for SIFIVE FU540.
- Add OF_SEPARATE support for SIFIVE FU540.
- Add SPL support for Andes AX25 AE350.
- Improve U-Boot SPL / OpenSBI smp boot flow for RISC-V.
At the start, OpenSBI relocates itself to its link address. If the link
address ranges of U-Boot SPL and OpenSBI overlap, the relocation can
lead to code corruption if a hart is still running U-Boot SPL during
relocation. To avoid this problem, the main hart is specified as the
preferred boot hart to perform the relocation. This fixes the code
corruption problems based on the assumption that since the main hart
schedules the secondary harts to enter OpenSBI, it will be the last to
enter OpenSBI. However it was reported that this assumption is not
always correct.
To make sure the assumption always holds true, wait for all secondary
harts to acknowledge the call-function request before entering OpenSBI
on the main hart.
Reported-by: Rick Chen <rick@andestech.com>
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Rick Chen <rick@andestech.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Add a wait option to smp_call_function() to wait for the secondary harts
to acknowledge the call-function request. The request is considered to
be acknowledged once each secondary hart has cleared the corresponding
IPI.
As part of the call-function request, the secondary harts invalidate the
instruction cache after clearing the IPI. This adds a delay between
acknowledgment (clear IPI) and fulfillment (call function) of the
request. We want to use the acknowledgment to be able to judge when the
request has been completed. Remove the delay by clearing the IPI after
cache invalidation and just before calling the function from the
request.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Rick Chen <rick@andestech.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Add the function riscv_get_ipi() for reading the pending status of IPIs.
The supported controllers are Andes' Platform Level Interrupt Controller
(PLIC), the Supervisor Binary Interface (SBI), and SiFive's Core Local
Interruptor (CLINT).
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
OpenSBI uses a relocation lottery to determine the hart to relocate
OpenSBI to its link address. In the U-Boot SPL boot flow, the main hart
schedules the secondary harts to enter OpenSBI before doing so itself.
One of the secondary harts will therefore always be the winner of the
relocation lottery. This is problematic if the link address ranges of
OpenSBI and U-Boot SPL overlap. OpenSBI will be relocated and therefore
overwrite U-Boot SPL while some harts may still run it, leading to code
corruption.
Avoid this problem by specifying the main hart as the preferred boot
hart to perform the OpenSBI relocation. The main hart will be the last
hart to enter OpenSBI, relocation can therefore occur safely.
The boot hart field was added to version 2 of the OpenSBI FW_DYNAMIC
info structure. The header file include/opensbi.h is synchronized with
include/sbi/fw_dynamic.h from the OpenSBI project to update the info
structure. The header file is recent as of commit
7a13beb21326 ("firmware: Add preferred boot HART field in struct
fw_dynamic_info").
Reported-by: Rick Chen <rick@andestech.com>
Suggested-by: Anup Patel <Anup.Patel@wdc.com>
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Rick Chen <rick@andestech.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Add descriptions about U-Boot SPL feature and how to build and run.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
Those are required for cfi-flash driver to get correct address information.
Also modify size description correctly.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
Add CPU2 and CPU3 information in cpus node
to support four cores SMP booting.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
For RV64, it will use sd instruction to clear t0
register, and the increament will be 8 bytes. So
if the difference between__bss_strat and __bss_end
was not 8 bytes aligned, the clear bss loop will
overflow and acks like system hang.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
When ax25-ae350 try to enable v5l2 cache
driver in SPL configuration, it need this
option for cache support in SPL.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
The mcache_ctl csr only can be manipulated in M mode.
Add SPL_RISCV_MMODE for U-Boot SPL to control cache
operation.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
Fix two wrong settings of andes plic driver as below:
1. Fix wrong pending register base definition.
2. Declaring the en variable in enable_ipi() as unsigned int instead of
int can help to fix wrong plic enabling setting in RV64.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
To get memory size from device tree instead of
get_ram_size(). This can avoid memory access fault
in U-Boot proper after PMP configurations in OpenSBI.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
This patch provides four configurations which can support U-Boot SPL
to boot from RAM or FLASH and then boot FIT image including OpenSBI
FW_DYNAMIC firmware and U-Boot proper images from RAM or MMC boot devices.
With ae350_rv[32|64]_spl_defconfigs:
U-Boot SPL will be loaded by gdb or FSBL and runs in RAM in machine mode
and then load FIT image from RAM device on AE350.
With ae350_rv[32|64]_spl_xip_defconfigs:
U-Boot SPL can be burned into SPI flash and run in flash in machine mode
and then load FIT image from SPI flash or MMC device on AE350.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
The U-Boot SPL will boot in M mode and load the FIT image which
include OpenSBI and U-Boot proper images. After loading progress,
it will jump to OpenSBI first and then U-Boot proper which will
run in S mode.
Also remove V5L2_CACHE due to U-Boot SPL code size consideration.
Without this concern, it can be enable manually for performance.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
This would help to make the necessary changes in drivers and device trees
in U-Boot tree itself. This feature would also be helpful to not pass
dtb during opensbi builds.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Rick Chen <rick@andestech.com>
Sync the hifive-unleashed-a00 dts from Linux with
below commit details:
commit <2993c9b04e616df0848b655d7202a707a70fc876> ("riscv: dts: HiFive
Unleashed: add default chosen/stdout-path")
Idea is to periodically sync the dts from Linux instead of
tweaking internal changes one after another, so better not
add any intermediate changes in between. This would help to
maintain the dts files easy and meaningful since we are
reusing device tree files from Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
