Since commit 34793598c8 ("mtd: nand: mxs_nand_spl: Remove the page aligned
access") there are no longer any users of nand_get_mtd. However, it is
still important to know what the page size is so we can allocate a
large-enough buffer. If the image size is not page-aligned, we will go off
the end of the buffer and clobber some memory.
Introduce a new function nand_page_size which returns the page size. For
most drivers it is easy to determine the page size. However, a few need to
be modified since they only keep the page size around temporarily.
It's possible that this patch could cause a regression on some platforms if
the offset is non-aligned and there is invalid address space immediately
before the load address. spl_load_legacy_img does not (except when
compressing) respect bl_len, so only boards with SPL_LOAD_FIT (8 boards) or
SPL_LOAD_IMX_CONTAINER (none in tree) would be affected.
defconfig CONFIG_TEXT_BASE
======================= ================
am335x_evm 0x80800000
am43xx_evm 0x80800000
am43xx_evm_rtconly 0x80800000
am43xx_evm_usbhost_boot 0x80800000
am43xx_hs_evm 0x80800000
dra7xx_evm 0x80800000
gwventana_nand 0x17800000
imx8mn_bsh_smm_s2 0x40200000
All the sitara boards have DDR mapped at 0x80000000. gwventana is an i.MX6Q
which has DDR at 0x10000000. I don't have the IMX8MNRM handy, but on the
i.MX8M DDR starts at 0x40000000. Therefore all of these boards can handle a
little underflow.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NAND
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On Altera SoCFPGA, upon either cold-boot or power-on reset, the
Denali NAND IP is initialized by the BootROM ; upon warm-reset,
the Denali NAND IP is NOT initialized by BootROM. In fact, upon
warm-reset, the SoCFPGA BootROM checks whether the SPL image in
on-chip RAM is valid and if so, completely skips re-loading the
SPL from the boot media.
This does sometimes lead to problems where the software left
the boot media in inconsistent state before warm-reset, and
because the BootROM does not reset the boot media, the boot
media is left in this inconsistent state, often until another
component attempts to access the boot media and fails with an
difficult to debug failure. To mitigate this problem, the SPL
on Altera SoCFPGA always resets all the IPs on the SoC early
on boot.
This results in a couple of register values, pre-programmed by
the BootROM, to be lost during this reset. To restore correct
operation of the IP on SoCFPGA, these values must be programmed
back into the controller by the driver. Note that on other SoCs
which do not use the HW-controlled bootstrap, more registers
may have to be programmed.
This also aligns the SPL behavior with the full Denali NAND
driver, which sets these values in denali_hw_init().
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-09-20 20:10:49 +05:30
Renamed from drivers/mtd/nand/denali_spl.c (Browse further)
