The CONFIG_MAX_NAND_CHIPS never used, remove it
No where define LCD_TEST_PATTERN, so no need undefine
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
the smc cs related registers start at 0x600 and loop with 5 registers
so the reserved register should be in at91_smc structure while no in
at91_cs structure. So fix it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
1. if CONFIG_SYS_NAND_ONFI_DETECTION is defined, driver will check NAND flash's
ecc minimum requirement in ONFI parameter.
a) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are defined. then use it.
Driver will display a WARNING if the values are different from ONFI
parameters.
b) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are not defined, then use
the value from ONFI parameters.
* If ONFI ECC parameters are in ONFI extended parameter page, since we
are not support it, so assume the minimum ecc requirement is 2 bits
in 512 bytes.
* For non-ONFI support nand flash, also assume the minimum ecc
requirement is 2 bits in 512 bytes.
2. if CONFIG_SYS_NAND_ONFI_DETECTION is not defined, just use CONFIG_PMECC_CAP
and CONFIG_PMECC_SECTOR_SIZE.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
In this way, the pmecc corraction capbility can change in run time.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Since kernel code current use many dev_xxx() instead of using printk. To
compatible, move those dev_xxx from usb driver to linux/compat.h. Then all
driver code can use dev_err, dev_info and dev_vdbg.
This patch also removed duplicated macro definitions in usb driver.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Define the galois index table offset in chip head file. So user do not need
to set by himself. Driver will set it correctly according to sector_size.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
[rebased on master]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
as the at91sam9n12 and at91sam9x5 soc support PMECC, when use u-boot
to flash the rootfs, in order to avoid flash one sector with all 0xff
into NAND, so use nand trimffs subcommand to avoid it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
add gmac support for sama5d3xek board, the gmac embedded in:
- sama5d33, sama5d34, sama5d35
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
fix the following building warning
---8>---
macb.c: In function 'macb_init':
macb.c:400:14: warning: 'phydev' may be used uninitialized in this function
macb.c:377:21: note: 'phydev' was declared here
---<8---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Without this change, the following message is generated:
Warning: FEC using MAC address from net device
See doc/README.enetaddr for details.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
The target uses AUART 3 instead of the DUART for console output.
Signed-off-by: Andreas Wass <andreas.wass@dalelven.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
The driver makes it possible to use an application UART as
the U-Boot output console for Freescale i.MX23/i.MX28 devices.
Signed-off-by: Andreas Wass <andreas.wass@dalelven.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Our Linux kernel switches the HDMI connector onto IPU0/DI1,
but the U-Boot display driver only supports IPU0/DI0 for the
time being.
Because of this, a soft re-boot will leave the HDMI output
connected to the wrong display port and prevent video from
being displayed.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Multiple read/write transactions initiated by security
engine may cause system to hang.
Workaround: set MCFGR[AXIPIPE] to 0 to avoid hang.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
There was a bug for calculating ddr_freq_mhz,
it should be divided by 1000000 rather than 0x1000000.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Also some fix for QSGMII.
1. fix QSGMII configure of Serdes2.
2. fix PHY address of QSGMII MAC9 & MAC10 for each FMAN.
3. fix dtb for QSGMII interface.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
When using QSGMII protocols, the first lane and third lane on each slot
need to be swapped.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Since the parameters need to be modified according to different Serdes
protocols at runtime, the const will block this. Also remove const from
arrays define used by vsc3316_config.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Makes the startup output more consistent
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Makes the startup output more consistent
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
This patch cleans up license header in these files:
board/freescale/p1022ds/spl.c
drivers/mmc/fsl_esdhc_spl.c
drivers/mtd/spi/fsl_espi_spl.c
Signed-off-by: York Sun <yorksun@freescale.com>
85xx, 86xx PowerPC folders have code variables with CamelCase naming conventions.
because of this code checkpatch script generates "WARNING: Avoid CamelCase".
Convert variables name to normal naming convention and modify board, driver
files with updated the new structure.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
TPL is introduced in the patch "NAND: TPL : introduce the TPL
based on the SPL", here enable TPL for p1022ds nand boot.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Due to the nand SPL on some board(e.g. P1022DS)has a size limit, it can
not be more than 4K. So, the SPL cannot initialize the DDR with the SPD
code. This patch introduces TPL to enable a loader stub that is loaded
by the code from the SPL. It initializes the DDR with the SPD or other
operations.
The TPL's size is sizeable, the maximum size is decided by the memory's
size that TPL runs. It initializes the DDR through SPD code, and copys
final uboot image to DDR. So there are three stage uboot images:
* spl_boot, * tpl_boot, * final uboot image
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
This patch introduces SPL to enable a loader stub that being loaded by
the code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
The code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
1. The symbol CONFIG_SPL_NAND_MINIMAL is unused, so deleted it.
2. Some functions were unused in the minimal SPL, but it is useful
in the common SPL. So, enabled some functionality for common SPL.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
The functionality env_import will be used in the SPL. They
had been excluded by ifndef CONFIG_SPL_BUILD. Now, put it
into the SPL.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: York Sun <yorksun@freescale.com>
After introduction of unified i2c model, the I2C_SET_BUS() macro is regarded
as obsolete.
Hence it is replaced with i2c_set_bus_num() function call.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
New I2C framework, introduced after v2013.07 final release, imposed I2C
code adjustment for some Samsung boards - namely Trats, GONI and Universal_c210.
Those boards were using schematic based I2C enumeration (I2C_5, I2C_9).
However, new I2C framework imposes usage of logical I2C adapters numbering
(e.g. I2C_0, I2C_1, etc).
Additionally, I2C_GET_* macros were replaced with i2c_*_bus_num() functions.
Trats board gained definition of second soft I2C adapter.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
The I2C_MULTI_BUS needs to be defined for correct I2C operation with
many software emulated I2C controllers.
This fix restores correct value of the I2C_MULTI_BUS changed by following
commit:
SHA1: 385c9ef5a7
i2c: add i2c_core and prepare for new multibus support
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
This workaround is for the erratum I2C A004447. Device reference
manual provides a scheme that allows the I2C master controller
to generate nine SCL pulses, which enable an I2C slave device
that held SDA low to release SDA. However, due to this erratum,
this scheme no longer works. In addition, when I2C is used as
a source of the PBL, the state machine is not able to recover.
At the same time, delete the reduplicative definition of SVR_VER
and SVR_REV. The SVR_REV is the low 8 bits rather than the low 16
bits of svr. And we use the CONFIG_SYS_FSL_A004447_SVR_REV macro
instead of hard-code value 0x10, 0x11 and 0x20.
The CONFIG_SYS_FSL_A004447_SVR_REV = 0x00 represents that one
version of platform has this I2C errata. So enable this errata
by IS_SVR_REV(svr, maj, min) function.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
When the code detected that the bus is hung (e.g. SDA stuck low),
send 9 pulses on SCL to try to fixup the bus.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
This way, we don't have to run mkimage on them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Disabling the data cache is no longer required to boot Dalmore, so
enable it. This results in notably better performance when loading
and booting the Linux kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Currently all Tegra SoCs are assumed to have 32 byte cache lines. This
isn't true for Tegra114, however, which uses 4 Cortex-A15 cores and
therefore uses a cache line size of 64 bytes. Move the cache line size
setting to the per-SoC common configuration file.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
SPL defines CONFIG_SPL_BUILD but this does not percolate to the
autoconf.mk Makefile. As a result the build breaks when
CONFIG_SPL_BUILD is used in the board-specific include header file. With
this, there is a possibility of having a CONFIG option defined in the
header file but not defined in the Makefile causing all kinds of build
failure and problems.
It also messes things for up, for example, when one might want to
undefine options to keep the SPL small and doesn't want to be stuck with
the CONFIG options used for U-boot. Lastly, this also avoids defining
special CONFIG_SPL_ variables for cases where some options are required
in U-boot but not in SPL.
We add a spl-autoconf.mk rule that is generated for SPL with the
CONFIG_SPL_BUILD flag and conditionally include it for SPL builds.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Ying Zhang <b40530@freescale.com>
The file header indicated that this file was GPL-2.0+, but actually
the code was derived from (Marvell based) Linux source code which is
only GPL-2.0. Fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Stefan Roese <sr@denx.de>
This commit adapts the files that were derived from PIBS (PowerPC
Initialization and Boot Software) codeto using SPDX License
Identifiers.
So far, SPDX has not assigned an official License ID for the PIBS
license yet, so this should be considered preliminary.
Note that the following files contained incorrect license information:
arch/powerpc/cpu/ppc4xx/4xx_uart.c
arch/powerpc/cpu/ppc4xx/start.S
arch/powerpc/include/asm/ppc440.h
These files included, in addition to the GPL-2.0 / ibm-pibs dual
license as inherited from PIBS, a GPL-2.0+ license header which was
obviously incorrect. This has been removed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Conflicts:
Licenses/README
Acked-by: Stefan Roese <sr@denx.de>
