Commit graph

23 commits

Author SHA1 Message Date
Masahiro Yamada
dacdb24027 ARM: uniphier: do not setup pins for System Bus on NAND boot mode
For LD11 and LD20 SoCs, the System Bus and NAND are multiplexed
in the same I/O pins.  When booting from a NAND device, pin-mux
for the System Bus must not be set-up because they are exclusive
with each other.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-10-10 10:03:23 +09:00
Masahiro Yamada
c72f4d4c2e ARM: uniphier: add PLL init code for LD11 SoC
- Initialize PLLs (SPL initializes only DPLL to save the precious
   SPL memory footprint)
 - Adjust CPLL/MPLL to the final tape-out frequency
 - Set the Cortex-A53 clock to the maximum frequency since it is
   running at 500MHz (SPLL/4) on startup

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-23 01:00:23 +09:00
Masahiro Yamada
682e09ff9f ARM: uniphier: add PLL init code for LD20 SoC
Initialize the DPLL (PLL for DRAM) in SPL, and others in U-Boot
proper.  Split the common code into pll-base-ld20.c for easier
re-use.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-19 00:12:26 +09:00
Masahiro Yamada
6a3e4274e4 ARM: uniphier: move PLL init code to U-Boot proper where possible
The PLL for the DRAM interface must be initialized in SPL, but the
others can be delayed until U-Boot proper.  Move them from SPL to
U-Boot proper to save the precious SPL memory footprint.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-19 00:06:44 +09:00
Masahiro Yamada
68557ec37e ARM: uniphier: consolidate System Bus pin-mux settings for LD11/LD20
Use the pin-mux data in the pinctrl drivers by directly calling
pinctrl_generic_set_state().

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18 23:47:18 +09:00
Masahiro Yamada
6a93478b93 ARM: uniphier: remove ad-hoc pin-mux code for sLD3
These settings are nicely cared by the pinctrl driver now.  Remove.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18 23:10:37 +09:00
Masahiro Yamada
667dbcd01d ARM: uniphier: add PH1-LD11 SoC support
This is a low-cost ARMv8 SoC from Socionext Inc.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-05-26 00:37:13 +09:00
Masahiro Yamada
0bd20207ab ARM: uniphier: disable cache in SPL of PH1-LD20
The Boot ROM has enabled D-cache and MMU setting DDR memory area
as Normal Memory in its page table.  Disable D-cache and MMU
before jumping to U-Boot proper.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-05-26 00:35:26 +09:00
Masahiro Yamada
bef4b024e9 ARM: uniphier: move pin-mux code into pin_init function
The code in uniphier_sld3_sbc_init() is pin-muxing, so it would
be a better fit in uniphier_sld3_early_pin_init().

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-05-01 01:13:45 +09:00
Masahiro Yamada
5eb4150e84 ARM: uniphier: allow to use System Bus for ROM boot mode of PH1-LD20
The System Bus is not available by default on the ROM boot mode of
PH1-LD20.  To use devices connected to the System Bus, such as the
Micro Support Card, it is necessary to set up pin-muxing and some
System Bus Controller register.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-05-01 01:09:18 +09:00
Masahiro Yamada
9d0c2ceb35 ARM: uniphier: add PH1-LD20 SoC support
This is the first ARMv8 SoC from Socionext Inc.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-24 09:54:08 +09:00
Masahiro Yamada
5b66006646 ARM: uniphier: rename function names ph1_* to uniphier_*
Eliminate the "ph1"_ prefixes from function names because "uniphier_"
describes the SoC familiy better.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:59:47 +09:00
Masahiro Yamada
d5cf32977f ARM: uniphier: support Debug UART
For ARM32 architecture, CONFIG_DEBUG_LL is available for early
low-level debugging (and actually UniPhier 32bit SoCs use it), but
ARM64 architecture does not support it.  Instead, CONFIG_DEBUG_UART
is available as an architecture-independent debug facility.

This commit supports it on all the UniPhier SoCs (including the new
ARMv8 SoCs), which is very useful for new SoC bringups.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-24 01:45:41 +09:00
Masahiro Yamada
5d0607c58c ARM: uniphier: refactor SBC init code
There is a bunch of duplication in the System Bus Controller init
code.  Roughly, there are two types in the SBC mode:  Adress/Data
Multiplex Mode and Save Pins Mode.  Consolidate per-SoC functions
into the two, plus per-SoC optional init code.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-24 01:45:18 +09:00
Masahiro Yamada
ea65c98050 ARM: uniphier: drop PH1- prefix from CONFIG options and file names
The current CONFIG names like "CONFIG_ARCH_UNIPHIER_PH1_PRO4" is too
long.  It would not hurt to drop "PH1_" because "UNIPHIER_" already
well specifies the SoC family.  Also, rename files for consistency.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-24 01:42:13 +09:00
Masahiro Yamada
15607d0d94 ARM: uniphier: add DRAM init code for ProXstream2/PH1-LD6b
As mentioned in the log of commit 019df879a9 (ARM: uniphier: add
ProXstream2 and PH1-LD6b support), the DRAM init code was missing
for a long time.  Finally, here it is.  SPL works now.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-01-13 01:54:55 +09:00
Masahiro Yamada
107b3fb484 ARM: uniphier: move headers out of include/mach directory
These headers are only included locally in arch/arm/mach-uniphier/.
There is no reason to export them by putting in the mach/ directory.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-01-13 01:54:53 +09:00
Masahiro Yamada
9475f8de88 ARM: uniphier: kill bogus header includes
These includes are not necessary.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-01-13 01:54:38 +09:00
Masahiro Yamada
6ba60fafda ARM: uniphier: call uniphier_get_board_param() without FDT blob
Move "gd->fdt_blob" from the caller to the callee so that this
function can be used more easily.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-12-23 00:08:40 +09:00
Tom Rini
da58dec866 Various Makefiles: Add SPDX-License-Identifier tags
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one.  This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.

Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-11-10 09:19:52 -05:00
Masahiro Yamada
019df879a9 ARM: uniphier: add ProXstream2 and PH1-LD6b support
The DDR SDRAM initialization code has not been mainlined yet, but
U-Boot proper should work.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25 00:59:33 +09:00
Masahiro Yamada
28f40d4a4d ARM: uniphier: add PH1-Pro5 support
The DDR SDRAM initialization code has not been mainlined yet, but
U-Boot proper should work.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25 00:59:28 +09:00
Masahiro Yamada
323d1f9d5b ARM: uniphier: allow to enable multiple SoCs
Before this commit, the Kconfig menu in mach-uniphier only allowed us
to choose one SoC to be compiled.  Each SoC has its own defconfig file
for the build-test coverage.  Consequently, some defconfig files are
duplicated with only the difference in CONFIG_DEFAULT_DEVICE_TREE and
CONFIG_{SOC_NAME}=y.

Now, most of board-specific parameters have been moved to device trees,
so it makes sense to include init code of multiple SoCs into a single
image as long as the SoCs have similar architecture.  In fact, some
SoCs of UniPhier family are very similar:
 - PH1-LD4 and PH1-sLD8
 - PH1-LD6b and ProXstream2 (will be added in the upcoming commit)

This commit will be helpful to merge some defconfig files for better
maintainability.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-09-25 00:58:38 +09:00